Carrier downpipes second run
 

Hi,

I am making a second run off carrier down pipe sets with plain 1 1/2" ends as before, I have two sets spare at this moment, these will be double welded (inside and out) and are all quality stainless. Will price them up when I get a price from the laser cutters for the flanges.

Richard, Yours will be with the original flanges as supplied.

Let me know if anyone is interested.

Kevin.

I could do with a set mate

They fit, with plenty of length if necessary to adjust them.
If you are making your own, remember they are left and right handled ...
Good work Kev.

Hi michael, if you are making your own, one word of warning, they are not a mirror image of each other!, one has a longer throw, we first made a left one then thought the other side would be the same with the flange turned to suit, how wrong we were!. If you going to make them bolt on your flange and align the pipe before cutting and welding, we have a jig built for these now.

Will set two aside for you.

Kevin.

Materials ordered and paid.
 

Gents, Those who have expressed an interest in the down pipes, I have ordered and paid for the laser cut flanges and pipe bends.

The following people want them.

Richard x 1 set, already paid, (picked your flanges up today, perhaps go for some new stainless?, additional £20)
Ben x 1 set. CASH PAYMENT ARRANGED.
Rick x 1 set, already paid.
Fred R X 3 sets. paid
Meduffer x 1 set.
Carrier Barry x 1 set.
Nick Bullock x 1 set. PAID.
Me x 2 sets. PAID.
Neil Ashley x 1 set paid
They are working out at £65 a set. One set left up for grabs on this run.

Kevin.

Please Paypal / cheque / bank transfer me ASAP, 'money owed' payment if using Paypal.

Just a wee tip
your pipes should be undersized then enlarged again at the end
or with the engine movement you make break the manifolds
also why the heavy duty flanges I think they should be 1/4 inch
it makes them easier to install without taking the studs out
Just my opinion (Again) !
I also recognize those hands cutting them off

Hi Stew, Valid points, what I have found with the bottom castings is that after 70 odd years they can vary in inside diameter vastly, once cleaned up, grit blasted etc, if you were to have the ends produced and sent to you as per original spec they may well rattle around in there, so its up to the individual to finish the ends to suit there casting. I think you can still fit a nut on the original studs?, these are thicker as I have seen a lot of warped flanges, but only by 5mm.

Kevin.

Kevin matey, did you post the bits in the end, as nothing has arrived yet ? Just concerned in case they have been swallowed up by the postal machine :-)

Rich, not yet, only picked up the flanges today, going to be a couple of weeks to fit in with work and family.

Kevin.

Kevin

I should get upthe bank tommorrow.

I asume you have missed the word set off the end of my requirements.

Update
 

Richard x 1 set, already paid, POSTED
Ben x 1 set. Paid. delivered
Rick x 1 set, paid. POSTED.
Fred R X 3 sets. POSTED.
Meduffer x 1 set. paid, posting Monday.
Carrier Barry x 1 set.
Nick Bullock x 1 set. paid. posting Monday.
Neil Ashley x 1 set posting Monday.
These are get done slowly so thanks for your patience

Kevin.

downpipes
 

Gents, check your private message boxes those still waiting for the pipes as they are now done.

I have one other set ready if anyone wants a set please remind me again even if you have already sent an email.

kevin.

I have four more pairs of these pipes left if anyone wants a set, these are the last ones, not making any more, they are all stainless : £70 a set.

Pm if you need some.

You could keep a pair over for me then as you were going to replace a bad one for me, and I cannot tell you which one it is.

Downpipes
 

Kevin,
I have a customer here in the US that needs a set. Please post a set to me. Can pay you thru paypal. Call me if you have an issues.
Thanks
John Bizal

Last set but one left.
 

One more set available, no more after this.


Kevin.