View Single Post
  #7  
Old 04-04-21, 01:32
Chris Suslowicz Chris Suslowicz is offline
Junior Password Gnome
 
Join Date: May 2007
Location: England
Posts: 814
Default

Further thoughts:

All the kit required for the Truck & Ground Station is listed in FZ 256/3, and would be issued as the "Set & Standard Kit" plus the dedicated "Installation Kit" for the intended use.

The "Set & Standard Kit" contains all the common parts for an AFV install, some of which (such as the Carrier No.1, waterproof covers, etc.) would not be required and had to be returned to stores.

The "Installation Kit" contained all the items needed to complete the particular installation, including all the cable clips and fasteners, installation and disposal drawings, etc.

So for the Truck & Ground Station, the aerial rods (F & G) and bases (8 (or 10) and 9) would be in the Set & Standard Kit, and the Installation Kit would supply the wire aerials (70, 90, 110, 150, 185 and 250-foot), Aerial Base No.9A (the 'B' set base for demounted use - basically a No.9 on a big spring clamp), two of the long co-ax feeders (Leads Aerial No.3/Connector Coaxial 11A), one for permanent installation in the truck and the other for use with the clamp-on base, and all the other bits & pieces, cables, extra headgear, satchels, etc.

FZ 256/3 is a really useful EMER, and you should get your hands on a copy.

As far as the cables required go (and they're all listed, along with the components needed to make them up from stores if required) are concerned:

Connectors, 4-point, No.32 - Switchboard, Charging, C5 or 2 batteries to set (demounted use)
Connectors, 12-point, No. 1E - WS19 to Control Unit 3B
Connectors, Co-axial, No.11A (Qty 2) WS19 B set to Base No.9 and 9A (demounted use)
Connectors, Single, No.7C - Aerial socket on WS19 carrier to mast
Connectors, Single, No.23 12V+ from Vehicle Switchboard to Switchboard, Charging, C5
Connectors, Single, No.23A 12V- from Vehicle Switchboard to Switchboard, Charging, C5
Connectors, Single, No.24 - Battery 1 12V+ to Switchboard, Charging, C5
Connectors, Single, No.24A - Battery 1 12V- to Switchboard, Charging, C5
Connectors, Single, No.24B - Battery 2 12V+ to Switchboard, Charging, C5
Connectors, Single, No.24C - Battery 2 12V- to Switchboard, Charging, C5
Connectors, Single, No.33 - Earth clip on Carrier 23 to vehicle Earth
Connectors, Twin, No.53 - Switchboard, Charging, C5 to Batten, Terminal (set), I think.
Connectors, Twin, No.77 - Batten, Terminal to WS19 Supply Unit No.2

There are also other connectors involved - the 'A' set aerial uses Aerial Feeder No.9 to connect the variometer to Base No.8 (or 10), and Connector, Single, No.33 for earth in the vehicle, and there's a Leads, Earth, No.2 for use with an earth pin and/or counterpoise when demounted, and either 'F' rods (or the plug on the wire aerial) into the fixed socket on the variometer mounting plate or Connector, Single, 7C from that to the 34-ft mast insulator terminal.

I think most of this is correct. (I'm not sure if the fused switchboard in your vehicle replaces the charging switchboard altogether for use in the vehicle.)

The battery link cables are not listed (Connector, Single, No.3) and are presumably supplied with the batteries. Likewise the cable from Chore Horse to Switchboard, Charging, C5 is part of the Chore Horse installation kit.

Best regards,
Chris.
Reply With Quote