[Bob Carriere]

Thanks for thinking of me guys.

Everyone here is surviving the Covid bug as best we can..... easier to do as I live in a rural area away from crowds and there is room to go for a walk without seeing anyone and never leave the property. However, the whole issue with extensive news coverage does drag you down after a while. Never had cabin fever during Spring time but here we go. Spring here as been ideal, with no snow precipitation during the whole month of March....... but I do miss the ability to drive to the village and pickup some nuts and bolts, etc. working alone in the fresh Spring air is nice but not has pleasant as having some one else around to chit chat,compare notes, swap ideas and gets outright boring after a while.

Nonetheless, Rob and Grant have dropped in and we did chat, at a socially ans scientifically approved distance and we have 95% completed our long desired "rotisserie" that will allow me to install one of by better, out of 3,
2B1 cargo box for a thorough revitalization. The one targeted has a very good floor, underpinning and the fender wells in place..... the rest will need surgical interventions and repairs. We will aim to do it has accurately as possible and being able to rotate the whole cargo box any which way will great simplify repairing panels with new steel.

I will later this week have pictures of the new "rotisserie" which was co built and co designed with Grant and strong enough to to handle the weight of CMP and eventually LRDG.

Can not pass the opportunity to rant and lament the price of steel since the Covid crisis........ some parts (TSC in particular) is not publishing a sales brochure until the stores are allowed to go wide open.....so buying bulk bolts is $6.00 a pound instead of the $2/95 sales price..... new steel is going up every time the local fabricator places a new order...... a 10 foot section of 2.5 x 2.5 in. 1/4 in. thick trailer receiver tube is now $10.60....last fall around $5.00..... and deliveries are sporadic based on whenever they get an order for the Ottawa area.........so building the "rotisserie" entirely out of 1/4 inch thick 2x2 and 2.5x2.5 has been much more than I expected.

Now to the LRDG the mud as now dried and I can now gather all the various frames in one place so I can compare frames, conditions, size, etc.......

I still have concerns about building the smaller version with a "Indian" wooden box due to the requirement to consider from the outset the need for sheltered storage as the wood components will not last long in Canadian hot/cold/dry/wet weather but.........considering the price of steel for a whole cargo box it maybe the way to go.

I have most of the drive train components, fresh rebuilt engine, spare tranny, plenty of rear ends to choose from and the following chassis..

A fully restored 1937 Chev one ton frame, brakes, linings, bearings all done sitting on original 16 inch Chev truck frame.... car style rims with drop center and a car type brake system........ a 1940 Chev cab would fit beautifully but it is a 1937 One ton GE model, 122 1/4 wheel base with 14" in. brake drums .... so slightly longer. The Good Year diamond threads all agri. weather tires would fit nicely.

I also have a 1940 1533 1.5 ton truck with cab ( long box is shot) but with complete drive train that would need a total overhaul....with enclosed driveshaft tube........ now this has the proper size wheel base......currently shod on 7.50 balloon 20 inch tire/rims that could be replaced with the axles from the spare C15 and that would allow me to use readily available CMP rims and fully mounted set of 900x 16 Michelin tires......

The I also have a 1942 Maple Leaf 2 ton complete frame/power train that could be made into the Canadain/Windsor made LRDG.....
...and finally access to a 1942?? complete frame with CMP shock absorber and factory frame flat steel plate reinforcement attached.

So pondering is an issue.......

One thing is sure....there are none of the above real LRDG in Canada to copy from........ and right now the lighter "Indian" pattern with the darn wooden box is mighty attractive and would be UNIQUE even if 7 inches longer than the original............

That leaves me at the mercy of what information is collectively available from existing Indian model....and the similarly built Australian NO 1 model.......pictures.... measurements...... etc.

The cargo box looks fairly simple manufacturing construction based on available angle iron or U shaped channel, some flat steel...... and lots of wood.

Has anyone got the pertinent information for the box .....or ever built one?

Would be nice to get the board thickness, width and length .....could get underpinning ideas from the AEBD manual and try a local saw mill for a price quote.....lots of good hard white ash tree wood available as they all died in the last Chinese tree virus....... Once properly soaked with Clear POR 15 they should be almost water tight.....then primed and sand coloured top coat.

PS...... from the length of this email one could assume that "isolation at home" as had an effect on me!!!!!!!!