Ford Blitz Restoration/Rebuild

[Private_collector]

I had asked for umpires decision (moderator).

We both agreed that removal of inflammatory comments was warranted, from both parties posting, and moderator acted in best possible way available.

The matter isn't really worth dwelling on and I hope it doesn't cause formation of bad feelings between any of the brotherhood!

[Private_collector]

PA090296.jpg PA250436.jpg PA250437.jpg
Finally got the axle/diff casings sandblasted this morning, and etch primed in PM. The wooden plates I made for the open ends worked well, with only a slight blow through on the half with pinion. It was lucky I had wrapped pinion gear & bearings in a layer of rag. No grit got through to bearings as far as I can tell. There is no evidence of grit with turning the pinion.
PA090288.jpg PA250434.jpg
Picked up the two bearing cups for the inner axle shaft to diff assembly, and the guys at the bearing shop (Gympie Bearing Service) told me some very interesting information about the quantity of chinese fake bearing parts which are getting onto the market. The story goes that China are producing counterfiet 'Timken' bearings which are in near perfect Timken copy boxes.
He told me that Timken genuine bearings have the Timken name/logo on right upper corner of the box edges and the bearing No. & barcode on left bottom of same side. He tells me that any variation of this is definately a fake! I don't know if this is 100% true, but he stated it as fact and it was agreed from the other 2 staff present in the shop. He did actually show me a box with a fake from china that Timken had given them to show to people, and the differences were obvious once told what to look for. There are visible flaws in the chinese bearings as well. Buyer beware.

The bearing cups (Timken, 33462) cost $24.00 each incidentally.

[gjamo]

Sounds a bit like Chinese bolts I have found stamped Grade 8.8 and made out of plasticene.

[Lynn Eades]

If they are marked "8.8", that is metric "CLASS 8.8", which is roughly the same tensile strength as an imperial "GRADE 5".

[Private_collector]

I had some bad news yesterday. I went to check fit of the new bearing cups & seals, and realised I did not have the diff output shaft seals I needed. The ones I had were not correct size for this truck.

Shot into town this morning and spent an agonising 45min at Gympie Bearing Service looking for a modern replacement. They did find a suitable part but it was not in stock there, and not in stock anywhere in Australia! The bearing manufacturer does not even know if there is any available in other countries to import.

To prove that things are darkest before the dawn, I received am email from Ross Prince WWII vehicle parts, in Hervey Bay, he has these available and ready for despatch. It's only 90min drive from me, so if he is available, I will head up that way tomorrow and get them. Ross has always had every other part I have asked for, and this was no different!

Brake hubs & axle shafts have been blasted this morning (only bolt end of the axles), and I etched them this afternoon. All going well, everything should be painted tomorrow afternoon.

I bought some short lengths of 100NB steel tube to make bearing/seal installer yesterday. It was a PERFECT size for inner hub bearing cup, inner hub seal and output shaft bearing cup. Now I have to remember where I saw the photo of the installer construction. I think it was in either the MB-F1 or a Ford tool book I have somewhere.

P.S: Have been checking the tracking info for the rear wheel cylinders from USA. They are now "In Transit" Yaaaay

Won't sleep tonight!

[Bob Carriere]

Hi Tony

Always following up on others progress on resto projects..... good job.

For installing various size bearings we found that making adapters out of hard wood on a wood lathe is fast, cheap, fit well and they work well with less chance of damage..... besides once used they make good kindling in the wood furnace.

Bob C

[Private_collector]

Bob,

I would rather use wood. Have been trying to think of someone I know who has a lathe. There is actually a wood work museum in town, that opens weekends for tourists. They would have a lathe I guess, as they do demonstrations of old woodworking practices. Mostly wood milling. Not sure about turning. I will try to get a hold of someone today & ask.