|
#1
|
||||
|
||||
Wanted: Piston for Chev Engine
G'day Everyone!
We've come across a problem with a Chev Engine we're stripping down and doing up to put in my Blitz; one of the pistons is unsaveable. I need a piston similar to the one in the photo below. It has the number "1632" engraved on the bottom of it. If anyone has one they don't need, preferably in Australia if at all possible, would you be so kind as to contact me? Thanks for your help! Toby Last edited by Willanthry; 05-07-09 at 03:14. |
#2
|
||||
|
||||
A seller on e-bay currently has These pistons for a Chev 6, but they look different to yours. Seller has 3 sets listed, but doesn't specify if they are for a 216 or 235. Maybe a Chev specialist could chip in here and advise?
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should! |
#3
|
||||
|
||||
First of all, Chev never made a 239. That's a Ford. The 216s had cast iron pistons and the later 235s had aluminum pistons. I'm not sure about the early 235s. Before getting a piston you'd better make sure whether it's standard bore or oversize.
__________________
1940 Cab 11 C8 Wireless with 1A2 box & 11 set 1940 Cab 11 C8 cab and chassis 1940 Cab 11 C15 with 2A1 & Motley mount & Lewis gun 1940 Cab 11 F15A w/ Chev rear ends 1941 Cab 12 F15A 1942-44 Cab 13 F15A x 5 1942 cab 13 F15A with 2B1 box 1943 cab 13 F15A with 2H1 box 1943 Cab 13 C8A HUP 1944 Cab 13 C15A with 2C1 box 1943 Cletrac M2 High Speed Tractor MkII Bren gun carrier chassis x 2 |
#4
|
||||
|
||||
Yes, but there was also various brands of aftermarket 216 alloy pistons made , they were even made here . I've got a set of dome top 216 alloy pistons ..from EPAY years ago. They are about 30% lighter than the cast iron type.
Toby, if your bore size is 3.5" it will be a 216 ..I think Im correct Mike
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
#5
|
|||
|
|||
pistons
the 216 on epay are .020 o/s flat tops, there is a 235 dipper feed motor in my shed, have,nt lifted head to see if its a 4 ring piston.
__________________
macca C15 C15A |
#6
|
|||
|
|||
Piston
Toby
There are several steps to take to determine what piston you are after. 1. measure the bore accurately , ie snap gauges , digital verniers etc These engines came out as 3.500 inches ( blitz's )or 3. 5625 inches ( others ) and determine if bored out to o/size ( some piston manufactures stamp the o/s on the head of the piston. 2.Referring to the picture where you are hoisting out the engine and looking at the angle of the water pump inlet pipe I would say this is a blitz engine that originally had domed cast iron pistons and a single hole in the block where the water pump bolts up to.Check how many holes in your block . 3. Looking at the picture of the piston I would guess that it is made of aluminium alloy , so it may have been a replacement set at some time , maybe had a rebore at the same time. 4. Looking at the picture of the block with the pistons in it , they appear to be flat heads , so the replacement pistons may not have had domed heads. Check whether they are flat or not . Summary Blitz engines originally had domed cast iron pistons , were 216 ci , had single hole from water pump to block . A similar engine made about the same time had two holes into the block with flat top pistons , not many engine parts are interchangeable between these two engines. So firstly determine what engine you have. Regards Jim S.
__________________
jim sewell cmp and cckw Last edited by jim sewell; 04-07-09 at 16:08. |
Thread Tools | |
Display Modes | |
|
|