|
#1
|
|||
|
|||
C15A 2B1 cargo bed rebuild
Hi Guys,
The cargo bed looked solid on first inspection but as we unpicked the various panels there was no stopping. Barry Ring cheesed off with restoring Jeep tubs fancied a challenge. Can anyone assist, I'm after 4 long footman loops that are fixed to the inside of the wheel boxes? Much appreciated. Cheers Paul
__________________
1942 Ford GPW 1942 Harley WLA 1943 Willys MB 1940 BSA M20 1940 Morris Commercial CDSW Light Recovery 1942 CMP Chevrolet no. 12 cab 1944 Bedford MWD Last edited by Paul Edwards; 12-08-22 at 20:21. |
#2
|
|||
|
|||
Unpicking continues
__________________
1942 Ford GPW 1942 Harley WLA 1943 Willys MB 1940 BSA M20 1940 Morris Commercial CDSW Light Recovery 1942 CMP Chevrolet no. 12 cab 1944 Bedford MWD |
#3
|
|||
|
|||
Work in progress
__________________
1942 Ford GPW 1942 Harley WLA 1943 Willys MB 1940 BSA M20 1940 Morris Commercial CDSW Light Recovery 1942 CMP Chevrolet no. 12 cab 1944 Bedford MWD |
#4
|
|||
|
|||
More work in progress
__________________
1942 Ford GPW 1942 Harley WLA 1943 Willys MB 1940 BSA M20 1940 Morris Commercial CDSW Light Recovery 1942 CMP Chevrolet no. 12 cab 1944 Bedford MWD |
#5
|
|||
|
|||
Sources for footman loops - I'm not really suggesting you buy in North America and pay the cost to ship but these may give an indication of what's available.
https://www.beachwoodcanvas.com/order/productlist.cfm https://www.mcmaster.com/footmans-loops/ (McMaster are restrictive in where they ship to but their site is nice in giving dimensions.) |
#6
|
|||
|
|||
Nice to see the progress....
Nice job Paul......
I had rust in just about the same areas.......... I had to salvage the floor diamond plate patches from another spare cargo box. If you come up blank on the footman loops let me know as I am about to order 4 for mine and could reship to you possibly cheaper. I removed and saved all the special rivited holders sued with the 1940 early tarp which had leather straps with a key hole for the pins. I will now have to rivet them back on . I worked on my box using a large rotisserie that had a section of a CMP rear frame so that I could attach the box to the frame similar to actual set up. Notwithstanding the rigidity of our installation...... after careful measurements we found the floor was not perfectly flat but was slightly curved front to back which made fitting some of the side panels tricky. I am now stopped at getting the front head board panel and side drop panels done by a local fabricator as my bending brake is limited to 48 inches. I compared 3 separate cargo boxes.....all rusted..... and was amazed that the measurements were all approx. 1/4 inch more or less....... yet they were all 2B1....all had some slight differences of construction. What thickness steel are you using??? Cheers
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cargo bow removal | chris vickery | Post-war Military Vehicles | 4 | 12-10-20 18:01 |
Wanted: 1A2 Cargo box | Yeo.NT | For Sale Or Wanted | 0 | 30-03-18 20:03 |
3 Ton CMP Cargo Box | Colin Alford | Auction and Classified Ad Site Heads Up | 17 | 08-12-17 04:19 |
Plans for a 2B1 cab 11 cargo box....? | Bob Carriere | The Restoration Forum | 3 | 25-04-15 03:59 |
C15A Cargo Cover | Brad Mills | The Restoration Forum | 1 | 26-07-04 21:20 |