F8 Toolbox/Spare Tire Bracket Measurements

Jim Price · #1 27-01-09, 04:00

Started my search today for plans for the 8 cwt toolbox(es) and spare tire bracket along with the "floor" suport for the tire (and toolbox?). The only thing I've been able to find that shows a clear picture of all is the attached. However, I haven't been able to find anything that has all the details along with measurements to make them. If anyone out there has any suggestions/sources, I'd be most appreciative!

Regards,
Jim

cletrac (RIP) · #2 27-01-09, 05:04

Jim, take a closer look at that CD I sent you. In the C8 body drawings folder are all the dimensions and drawings you'll need.

Jim Price · #3 28-01-09, 00:28

David,
Tried to find the drawings on the disc last night and suffered some severe disfunction when operating the TV/DVD control wand. Gave up and sent the post. Tried again after your response and remarkably, my mastery of the wand had returned. Found all that I need!

Thanks again for the disc!

Regards,
Jim

Mike Kelly · #4 29-01-09, 02:46

Jim

Not sure what drawings you have ..but if they are the drawings from UK .

The lower locker floor length as shown on the drawing is about 1" shorter than it should be .

I studied the photos as best I could and the two long shaped angle iron pieces the lower locker is made from are different : the inner one ( bolts to the forward main panel of the tub ) is thinner/lighter than the forward one.
Mike

Jim Price · #5 29-01-09, 02:54

Mike,
I have a DVD from David Pope which has the drawings of the tool locker/spare tire holder on it. The problem I have is that I can only view it on my TV and cannot print out the drawings. If you have a set, I'd certainly appreciate having a copy!

Regards,
Jim

Mike Kelly · #6 29-01-09, 23:37

OK . I'll try to find em and post them here . you can do save and then print em . One thing , the shaped foot that the spare wheel sits on isn't in the drawings from memory . Ian cut out a template and I used that to make one.

The upper locker end piece is somewhat tricky to make , it's a flat/angled panel with 'U' shaped edges to fit into the locker sides. I had 3 attempts at it til I got it correct. I hand made the spare wheel latch .
Mike

cletrac (RIP) · #7 29-01-09, 23:56

Here's those UK drawings of the tool box and tire retainer.

Hanno Spoelstra · #8 30-06-20, 21:22

Quote:

Originally Posted by cletrac (RIP)

Jim, take a closer look at that CD I sent you. In the C8 body drawings folder are all the dimensions and drawings you'll need.

Sadly, David is no longer with us.

Could anybody share his C8 body drawings on here? I have been asked by a couple of people quite recently. I'm sure David would have liked to see new guys showing an interest in refabricating these 8-cwt bodies.

Mike Kelly · #9 01-07-20, 14:12

Quote:

Originally Posted by Hanno Spoelstra

Sadly, David is no longer with us.

Could anybody share his C8 body drawings on here? I have been asked by a couple of people quite recently. I'm sure David would have liked to see new guys showing an interest in refabricating these 8-cwt bodies.

Hanno the drawings were originally done by Ian Richardson of Lancashire UK, Ian measured the C8 1A2 body that now is owned by Nick Bullock. Ian posted me the drawings over a three year period . I ran a wanted advert in W&T and Ian responded , Ian owns a cab 11 C8 himself, haven't heard from Ian for many years now.

Hanno Spoelstra · #10 02-07-20, 12:42

Quote:

Originally Posted by Mike Kelly

Hanno the drawings were originally done by Ian Richardson of Lancashire UK, Ian measured the C8 1A2 body that now is owned by Nick Bullock. Ian posted me the drawings over a three year period . I ran a wanted advert in W&T and Ian responded , Ian owns a cab 11 C8 himself, haven't heard from Ian for many years now.

Thanks for that info Mike.

It begs the question: does anybody have Ian's drawings and can he share them on here, please?

Hanno Spoelstra · #11 02-07-20, 12:44

See the links for some excellent pictures of the 8-cwt truck and body.

CMP Truck 8-cwt Wireless:
http://www.rcsigs.ca/index.php/CMP_Truck_8-cwt_Wireless

Body 1A2 for Truck 8-cwt Wireless:
http://www.rcsigs.ca/index.php/Body_...8-cwt_Wireless

905px-Body_Parts_List_-_Body_1A2_for_Truck_8-cwt_Wireless_-_Factory_Photo_01.jpg