WANTED: UC No2MkII* speedo driven gear

[RichardT10829]

Marc are you refering to the brass adapter which screws into the hole on the cast peice that dirk showed you ? if so if you promise to give me it back i will lend you mine as a pattern to get one turned on a lathe...would not be a hard job for a capable person ?

[BCA]

Hi Marc,
If you mean the angle drive gear that clamps onto the speedometer then I have NOS ones in stock. Send me a PM.
This a cast fitting that the speedometer cable threads onto so you can attach the speedo cable to the speedometer. There must be properly greased and turn freely or the speedometer cable flexible shaft will break. This angle drive for Mk1 and M11 speedometers is diffrent than the T16 Carrier angle drive.
Brian

[Lynn Eades]

They are refering to the other (gearbox) end. I will post component pictures in the next 48 hrs.

[RichardT10829]

Marc this is the bit i was refering too

listed as part no CTL 2216 or is it the spindle from inside it which is listed as CTL 2510 B2

Richie

[Lynn Eades]

Heres the pics. Dirk your housing is interesting. It appears to have a seal in it. I havent seen one like that. My one has a "W" cast in it. Is that Windsor?
The speedo drive bits have all the faults.

[Dirk Leegwater (RIP)]

Originally Posted by Lynn Eades

Dirk your housing is interesting.

That's right Lynn, the Loyd Carrier have used the same gearbox
coupling, including the hard to find parts: Spindel & Coupling Gear.

Dirk

[RichardT10829]

Marc can you Pm / email me your address please, i have managed to get the spindle off without damaging anything. the parts i am sending are CTL2216 and drive spindle






Please bear in mind iam taking a risk posting a rare item to someone i have never met or spoken to for that matter, given recent issues surrounding a bren gun (nothing to do with us) lets show folk on MLU that people can be trusted here, and i look forward to recieving the goods back undamaged

(above a really posh way to say...i better get these bits back buddy )

cheers

Richie

PS you may find a few folk will want one of these so if your contact can make a few we could help folk further afield...i know Big Mike was after one of these not so long ago, plus those who have them but are worn / damaged

[Marc van Aalderen]

Originally Posted by BCA

Hi Marc,
If you mean the angle drive gear that clamps onto the speedometer then I have NOS ones in stock. Send me a PM.
This a cast fitting that the speedometer cable threads onto so you can attach the speedo cable to the speedometer. There must be properly greased and turn freely or the speedometer cable flexible shaft will break. This angle drive for Mk1 and M11 speedometers is diffrent than the T16 Carrier angle drive.
Brian

Hi Brian,

I didn't know that that is something I'm also missing. It does make sense as the space in the Dash is very limited so no room for the speedo cable to make a big radius bend. PM sent. Thank you.

Cheers, Marc

[Marc van Aalderen]

Hi Lynn and Richard,

You were both looking at the correct parts. I tried to find a picture of these parts in both workshop manual and Mk1* parts catalogue but there is absolutely nothing in either book. Then I looked in the later parts catalogue for Mk1* AND MkII*. This uses the same plate as the Mk1* parts catalogue but with the two items I need added! It shows the gear CTL2216 and housing CTL 2510 B2. So Richard, you were right there. !! Lynn's left picture says it all, they probably fail often...

Lynn or Richard, if nobody has NOS or used good parts for me can I borrow one of each part from either of you to have them made? I will off course return them after reproducing them.

BTW, Lynn the seal is also shown. Part number C01UC105387

Cheers,
Marc

[RichardT10829]

yes no problems buddy just keep me posted.