M38A1 fuel tank cleaning?

[rob love]

Rad places do gas tanks. Or you can source some POR15 and do it yourself. I believe Lordco carries it in your province. It is not rocket science to apply.

[SteveJ]

since you are totally cleaning out the tank I would suggest installing an original in tank filter. This will save you cutting up your fuel lines. Midwest military has them and they can be cleaned periodically and reused as per the TM.

[Casey B]

It has one in there already a redish brown cylinder correct?

What are these made from and do you think I need a new one?

Too late on the fuel line cuts as I have already put an inline filter in before the fuel pump and glad i did the tanks filter element was loose so the gunk got to the filter. Thanks look forward to your reply!

[Casey B]

Hi Rob yes I found the POr15 coating now wanted to know how you would protect the drain hole just let it run through and then run a tap through the threads after or put a bolt through then try to cut away the residue or build up after it is dry?

Also I was told the running for a few minutes then dying could be the condensor you think maybe? New plugs proper gap and clean fuel rebuilt carb...Idled for a long time 15-20 mins and then when you put it under load it dies within a few minutes and is flooding and will not restart!

[rob love]

Condensors usually work or they don't. Coils on the other hand will do what you are describing.

Only problem with a fuel filter before the fuel pump is that all the crap that's sitting in the pump itself still will have to work it's way through the carb needle. If flooding was a problem before, it still will be for a short time yet.

To install a filter at the carb, remove the pipe to flare brass fitting and replace it with a male pipe to female pipe elbow. Install a 70s (actually should be an early 80s) Ford fuel filter into the elbow then install the original line onto the fuel filter. No need to cut lines.

I would just let the POR go through the drain plug and then clean up the threads with a tap. The POR is tough, but not as tough as steel so the tap will have no problem. Check the internet for tips on using the POR products...there are plenty out there including on their own site.

[SteveJ]

The reddish brown cylinder is a resin core filter which would
be the factory install. Its cleanable and normally would require periodic cleaning every six months under normal use. When I got my M38 in 97 the tank also was full of crud so I pulled it out cleaned and repaired it. I also cleaned the fuel filter,carb and flushed clean fuel through the pump which would be normal for the level of maintenance you are doing. My jeep ran excellent with no fuel glitches since. Last year I changed the fuel gauge sending unit as it was erratic. As I was in there I also replaced the fuel filter with a new one from midwest. Again its still running great.

If you have already cut the line and installed the inline its done. I would still replace or clean the one in the tank then if you ever decide to go back to factory spec its just a matter of replacing the fuel feed line as you know you have a good filter in the tank. The factory install is nice and clean no strange looking add ons. Less fittings less chance of a leak.

[Casey B]

Hi Rob well lot's of good advice but again nothing that can't be replaced should someone want it looking original..I have a pic of the fuel filter that I got for a ford Late 60's early 70's and it is common as you said with a 90 degree elbow and threads as well...the opposite end is not a female flared type. Is there one with this they could not find it in their data base...? There is a pic of what I got and would have to either make the hose go over the flared end of the fuel line or have to cut it to allow the hose to fit the end. I think it would fit over but if there is one that can be fitted without this hose Love to get a part number from you. Thanks Rob

[rob love]

My mistake: Ford started using these in 1981.

Try a Wix 33081, or a Fram G3596DP. Or right from Ford it is a FG795A. The end will match right up to the existing jeep fuel line. Be careful not to cross-thread it.

Here is a pic of one:

[Casey B]

Yes Got it tonight and it fits like a glove Rob! I'll coat the tank and let you know how it works out! thanks again!

[Casey B]

Have to ask if the liner in the filler neck can come out prior to coating the tank also if so does the ring at the neck opening that the cap screws onto also come off to allow the long funnel liner to come out as well?
I know i can seal the tank with this in but want to know if it comes out and easily?
thanks!