|
|
#1
10-11-11, 04:21
|
||||
|
||||
Fuel line adaptors
Im wondering if anyone has 2 of the following fuel line adaptors? It is part # CTL 3485B
Im short 2 of them for my fuel line install. I tried part # C31UCW 104142 but they are a smaller fitting on one end and will not fit the thread size on the fuel pump or Mk1 fuel change over switch. Ive got 2 of the C31UCW 104142 to do an outright trade if needed.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer 
|
|
#2
10-11-11, 06:35
|
|||
|
|||
|
Jordan
It's probably 1/4 BSP on both ends. Very common. take your sample into your local engineering supplier
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#3
10-11-11, 06:37
|
||||
|
||||
|
Sadly it isn't. The fuel lines are 1/4 BSP fittings, but the other side that goes into the fuel selector or the fuel pump are something else. I do know modern brake lines pieces you can buy at a hardward/automotive store fit fine. I tried a fittings place and they could match one or the other but not both on the same piece.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer
|
|
#4
10-11-11, 07:26
|
|||
|
|||
|
Jordan
The other end is most likely 1/4 NPT then. If so, it will be slightly smaller in dia. If you check a ford manual for the fitting that goes into the petrol pump, it might verify that. I imagine there would be some demand, and somebody must make them.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... Last edited by Lynn Eades; 10-11-11 at 20:00.
|
|
#5
10-11-11, 14:31
|
|||
|
|||
|
NPTX Compression..
Quote:
That is 1/4"NPTX1/4"compression.. Weatherhead standard fitting.. Go to a real wholesaler..
__________________
Alex Blair :remember :support :drunk:
|
|
#6
10-11-11, 20:02
|
|||
|
|||
|
Alex
Jordan has already said one end is BSP.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#7
10-11-11, 20:29
|
|||
|
|||
|
Bsp
Quote:
Not having the fitting in my hot little hand I would think it would be a NPT x compression..SAE.. If so it is here.. http://shop.hoseandfittings.com/cata...dard/HF68.html IF it is some kind of BRIT fitting it would be here.. http://shop.hoseandfittings.com/cata...BSPT_x_MP.html Either way Jordon should be looking for a replacement in a proper hose or fitting supplier. Take the one he has and match it up here,,... http://www.hoseandfittings.com/ It is in Fort Wayne Indiana..but he could get the same thing at any decent hose shop.. He'll get a bunch..lots of hose shops in Hamilton.
__________________
Alex Blair :remember :support :drunk:
|
|
#8
10-11-11, 22:14
|
||||
|
||||
|
OK ive figured out the thread sizes. It is 1/4 NPT x 1/4 BSP
Thanks all for the input. I'll find some new made ones.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
