Finally getting around to working on my CGT

[Bob Carriere]

Try to remove everything you can to see if the crank can be lifted from the engine bottom in one piece...... then you can remove the clutch pack and the flywheel.

However, having said that I did have to cut one crank...... because I could not reach all the bolts on the connecting rods...... the pistons were rusted solid in the cylinders...... pounding with a wooden block and a sledge hammer did not free them up.......

And it will take you a lot of Oxy-acetelyne to cut through the crank......

If I can be of any help to sort out your 2 speed T case let me know. You are in for some fine welding to rebuild those crossmembers. I can't understand why they had to cut the crossmembers for extra clearance.....

Yes trannies can hold a lot of water.... yet most gears and bearing will survive. By the way all bearing/race are available even today as aftermarket parts........ a good indusrial bearing centre will find you a matching bearing by measuring thickness and ID and OD...... do not go by the part numbers most have changed. The bottom rear bearing is difficult to find... all others are there for the picking NOS brand new...... same goes for the T case bearings and seals.

Bob C

[Stony Smith]

Excellent advice on the engine -although I'm not going to reuse it as I have the 261 now. And your tranny knowledge about water has put my mind back at ease -till I take it apart

The transfer case selector shaft is pretty corroded -may look into finding a donor for that, however it's only metal.....

[Phil Waterman]

Hi Stoney

Two of my three CMPs have had water in the transmission, I think it gets around the shift lever particularly around the reverse lock out rod. One old Chevy GMC guy told me to pack the rod area with grease and grease the ball area once a year, he suggest removing the lever to do this. I've added doing the same to the transfer chase lever assembly.

Now as to water damage to the gears and bearings, take a look at http://canadianmilitarypattern.com/C...ansmission.htm which is old thread from MLU with more pictures added. (some of the pictures are high resolution and large so maybe slow downloading.) My C60S had some really nasty stuff in the transmission. Looked like brown 3 layer jello and about the same consistency when I first got the truck. Completely disassembled and cleaned the transmission and as you can see from the photos there is some gear tooth pitting and one of the shafts developed a chatter after 10 years of use. But now with 20+ years of driving it still shifts good.

Now about the "the transfer case selector shaft is pretty corroded" I assume you mean the tower assembly, or do you mean the shift shafts that actually go into the transfer case.

Think you will be happy with the 261 engine, the 261 engine in my C60S with radio box makes it a very enjoyable truck to drive.

Cheers Phil

[Stony Smith]

that's more great information on the tranny, thanks -interesting that even with the pitting on the gears they are still fine -mine feels a bit crunchy when I turn it over, I'll clean it up and get some new bearings -good as new.....

Transfer case is good -it's the tower that rusted solid -barley any bold head left on the top -that's this weekends project

[Phil Waterman]

Hi Stoney

Now when I encounter this problem of rust on gear teeth I polish them carefully with 3M Roloc Disc finest grit I can get. (I save my old discs after they lost their cutting power to use so they don't cut aggressively)

Then I polish each tooth being careful not to cut in to the metal just smooth and polish the teeth. Slow picky work.

Concerning the transfer shift tower, one of my trucks was rusted the other wasn't the one that wasn't had the entire shift tower filled with grease. That truck had signs of having been wade proofed, cosmoline all over the place, so wonder if filling the tower with grease was part of wade proofing. Did make it a little hard to shift in real cold weather.

Cheers Phil