|
|
|
|
#1
25-03-14, 04:03
|
|||
|
|||
Just wondering if some could please trace out a cardboard template of the 517/3 PIVOT DOOR RADIATOR FILLER COVER and post to me for a lp2 carrier . I need to make one , unless someone has a spare one .? Dale
__________________
1944 GPW and Bantam trailer 
|
|
#2
28-03-14, 12:02
|
|||
|
|||
|
Rainy couple of days at work so I detailed and sprayed my engine cover ,I'm still after a template to make a radiator cover hatch . Dale
  
__________________
1944 GPW and Bantam trailer Last edited by Dale Jordan; 28-03-14 at 12:08.
|
|
#3
01-04-14, 00:28
|
|||
|
|||
|
Thanks to Eben , He is sending me the template for the filler cap on the engine cover . Can someone tell me the length of the 5/16 UNF threaded rod that holds the clamps on the side of the carrier plus the ones on the rear plate are they different sizes do they all have lock nuts up against the threaded blocks that are weld to the hull ? I know they have wing nuts . Dale
__________________
1944 GPW and Bantam trailer
|
|
#4
01-04-14, 00:29
|
|||
|
|||
|
Thanks to Eben , He is sending me the template for the filler cap on the engine cover . Can someone tell me the length of the 5/16 UNF threaded rod that holds the tool clamps on the side of the carrier plus the ones on the rear plate are they different sizes do they all have lock nuts up against the threaded blocks that are weld to the hull ? I know they have wing nuts , also what does the fire extinguisher bracket look like ? . Dale
__________________
1944 GPW and Bantam trailer Last edited by Dale Jordan; 01-04-14 at 01:17.
|
|
#5
03-04-14, 11:37
|
|||
|
|||
|
I picked up a real nice track winch today this is my first good find , very nice feeling to get this peace . It could be NOS as No bad rust and it has that Dark grease on the nuts , other wise it's been sitting dry in a shed for years . Dale
 Plus and jack stand aswell  Winch came with the hold down straps and fasteners 
__________________
1944 GPW and Bantam trailer Last edited by Dale Jordan; 03-04-14 at 11:52.
|
|
#6
03-04-14, 13:41
|
|||
|
|||
|
Dale, with regard to the studs, I think they are all the same except there is one smaller one. I think they all have lock nuts (someone will correct me if I am wrong) and the all have a clip in a hole in the end, to stop the wing nut falling off. I would guess length at 2 inches.
Your track jack is nice. It is only missing its pin and knurled nut. Your jack bracket is different from the common one. Does yours belong to a specific carrier makers production, or is it an early/late thing?
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#7
03-04-14, 23:03
|
|||
|
|||
|
Thanks Lynn . Can someone tell me if the LH and RH track strainer arm no 582/5 and 582/6 parts to be straight or have a bend in them as in the list of spare parts . My one they bend in towards the spindle .? as in the first photo Dale
__________________
1944 GPW and Bantam trailer
|
|
#8
04-04-14, 00:18
|
|||
|
|||
|
They are originally straight.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Vic rail 2225 | colin jones | The Carrier Forum | 109 | 13-07-13 15:15 |
| My GM engine number when was it build?? | 8threcce | The Restoration Forum | 7 | 09-01-12 08:39 |
| Iltis carb re-build kit | servicepub (RIP) | Post-war Military Vehicles | 2 | 15-05-11 22:33 |
| How To Build A 2/5 Sherman Tank | T.J. | The Armour Forum | 1 | 16-01-08 11:17 |
| Pssst... want to build a gun tractor? | Keith Webb | The Softskin Forum | 12 | 16-07-04 00:13 |
Hybrid Mode
