How To: C15a Wire-3 restoration

[Jordan Baker]

Thanks Bob

Once I get to taking apart the roof rear panel I will be adding in the window I got from you. Much appreciated. The roof will need a lot of little bits redone and fixed.

For using JB Weld would you sandblast, then JB, then POR15?

I will try out the drip process when I get the chance.

[Bob Carriere]

Do all your welding, patching, grinding and JB, etc then do the sand blast.

Be carefull around the JB.... may need to lask it off or the sand will take it away faster than the surrounding steel. Even smal bolt holes welded and grinded.... get to shinny for the POR to really bind to the surface....... watch body oil from your fingers or dirty leather gloves...use blue ot thicker black nitrile and change as often as necessary. You may wabt to lower the pressure on the blaster and use the fine with sand from TSC so as not to be too agressive. Don't forget to spray a litght coat of paint prep aka Phosphoric acid and let air dry

The dilemma is we use the finest flap wheels to dress up butt welds to a smooth mirror like finish than we need to roughen it up for the POR....Duh!!!!

You are on the right track.

[Alex van de Wetering]

Jordan,

I don't have any experience with POR15 .....and don't think they have spray cans (?), but maybe this is an alternative.....I used Rustoleum rusty metal primer inside a hollow crossmember, with help of a small nozzle and thin hose.
The nozzle and hose came with a can of (Valvoline) bodysafe protective coat for sills and other hollow areas. While I am not a fan of this stuff and don't use it on the Chev, I did like the hose and nozzle.
I had to search my collection of spray can caps for a suitable one that would allow the hose to slide over the end....and fit the top of the Rustoleum can.

I sprayed a quick thin coat every evening of the week and cleaned the nozzle and hose afterwards by fitting the hose to a second cap that would fit a spray can of brake cleaner. A quick clean with brake cleaner and the hose and nozzle were ready to be used again.

Alex

[Bob Carriere]

Hi Everyone

Hi Alex..... they do sell special rust coating in cans at Eastwood USA and it has that same long reach nozzle. I have never used it but would be very good for enclosed area such as the windshield pillars and frames.

I like the idea of being able to reuse the long reach tube and cleaning it with spray brake cleaner.

Bob C

[Jordan Baker]

Thanks Alex and Bob for giving me a few different ideas. I ended up just doing the pour method as described by Bob. Lots of drips all over the place but I got it done. Next step will be getting the glass cut and installed then I can paint the frames their final colour.

[Jordan Baker]

Frames are all painted in the final coat of SCC2. Now I just need to get the glass cut and installed.

I also managed to get this small air filter cleaned up and repainted. Ive seen some NOS ones with a decal. Does anyone know where I might be able to get the proper decal?

[Jordan Baker]

Working on a variety of parts. I had Metal Supermarkets shear some 16ga sheet metal for me today. These are for the retaining strips on the side curtain frames. They were great to deal with and very fast. I did have to hand file them to remove the razor sharp edges. One is done so far.

I also picked up a pair of front canvas seals at the Ontario Regiment Museum open house.

Last pictures for now is the left side fuel tank. So far its been wire wheeled. I had two rust holes about the size of a dime each that needed to be fixed. I cut a patch with some sheet metal and then soldiered them in. Once the tank is painted they will be very hard to see. On the inside I will be doing an acid wash/rinse and then sealing with Mac's Autoparts fuel tank sealer. I did the tank in my UCarrier with this stuff and I was very happy with it.