![]() |
|
#1
|
|||
|
|||
![]()
Great project, it's sad to see how it was wrecked, but Still a great truck to complete! Is there any chance to find the roof, doors or other parts?
Good luck! Frankie |
#2
|
||||
|
||||
![]()
Hello
thank you frankie ![]() I think the doors and the roof will be impossible to find (in europe) But they are not very difficult do built , the body is made of square tubes, but its many hours job. Im just begining to clean the truck, and then I hope I will find a member which can give me some dimentions. regards Sylvain |
#3
|
||||
|
||||
![]()
Dont give up hope completely on finding the parts (doors etc.) if the body are the same as on a Chevy, odd things can be found in Norway.
Just let us know what dimensions you need, I can take measurements of my rebuild and my unrestored CGT cab 12's and I know that there are other very helpful gun tractor owners on here. cheers Niels
__________________
1941 Chevrolet, Cab 12 CGT, 7A2 body 1944 Ariel W/NG 1944 Scammell Pioneer SV/2S x 2 1955 Austin Champ, 04BF45 1946 Chevrolet 5400 COE, Civilian Last edited by Niels V; 04-11-15 at 19:30. |
#4
|
|||
|
|||
![]() Quote:
I thought the original ones cut from your truck.... I know about few cab 12 FGTs, I PM you details... I need few dimensions for a FGT, too, but cab 13... ![]() Frankie |
#5
|
||||
|
||||
![]()
HI
I see you will also have to work on your truck too ![]() Here is a picture of the roof found on internet, what do you think about ? Is the fine steel cross original , I ofen seen a big round tube cross? Can someone give me the dimentions of this opening? regards Sylvain |
#6
|
||||
|
||||
![]()
I might get time in the weekend, so I could measure mine.
both mine have a tube cross about 0.5 inch in diameter. I might have found a nose in Norway
__________________
1941 Chevrolet, Cab 12 CGT, 7A2 body 1944 Ariel W/NG 1944 Scammell Pioneer SV/2S x 2 1955 Austin Champ, 04BF45 1946 Chevrolet 5400 COE, Civilian Last edited by Niels V; 05-11-15 at 10:25. |
#7
|
||||
|
||||
![]()
HELLO
It would be nice if you could give me this sizes : ![]() can you also give me the hight of the windshield |
#8
|
||||
|
||||
![]()
What do you think about the rear body and the boxes
All the rear body looks very homemade, bad weldings, different size of steel... Is this rear body and boxes original or was it badly restaured? Regards Sylvain |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Is this CD any good? | Darren Witty | The Softskin Forum | 3 | 22-07-11 12:19 |
Chevys GM products good in the 40's still good | Lionelgee | The Softskin Forum | 19 | 17-10-09 12:05 |
A good day | Lionelgee | The Restoration Forum | 12 | 28-08-09 13:17 |
As good as new... | Hanno Spoelstra | The Softskin Forum | 7 | 26-10-06 21:12 |
It's no good....... | kevinT | The Armour Forum | 3 | 03-09-05 23:42 |