![]() |
|
#1
|
||||
|
||||
![]()
I believe that on the Wire3 the Chorehorse was hard mounted to the truck and that why it had the cover shown in the photos. I also believe as pointed to in my first post that you can make out the flexible exhaust hose running beside the fuel tank.
The following pictures are from a 8cwt wireless truck and clearly show the CH1-395-4 Canadian model chorehorse hard mounted to a bracket. They also show the flexible exhaust hose being run from the generator along the back wall of the cab and down to the frame with the muffler right beside the exhaust pipe for the truck. Further more being hard mounted would mean the wiring could all be run to the C5 charging board and batteries. This would mean that the only setup would be starting the generator and changing some knobs on the charging board. One other point I noticed in the wartime chorehorse manual is that it appears the CH1-395-4 Canadian model didn't come with any oil bath air filter. There is no mention of it in the text or the parts diagram. Whereas the CH1-395-5 British model specially mentions that it comes with one.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#2
|
|||
|
|||
![]()
Jordan's photos above seem to show a fixed plate in place of the common sliding rear window with a small, permanent opening (for communication tube between cab and crew in the rear?). Also, if all cab roofs are punched with the same holes regardless of intended use, the support brackets for the chorehorse exhaust might explain some otherwise unused holes in the back of the cab.
|
#3
|
||||
|
||||
![]()
Here is the inside of the cab for the 8cwt.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#4
|
|||
|
|||
![]() Quote:
I think my C8 has a hole in the curved corner of the rear wall which I think was done to clamp the exhuast hose.....but I don't see it on the Ford factory pics. If I remember correctly the only other holes in the rear wall on my truck are for the battery lead, top rifle clamps and the fire extinguisher. I am with you Jordan; that hose does indeed look a lot like the exhaust pipe of the Chore horse. I think your second picture even shows a heat shield or at least an angle iron (along the lower edge of the gas tank, between the two brackets) to protect the gas tank and route the exhaust hose. I don't see any problems with it being run on the cab step.....and that means the wire guard would not make sense either (sheet metal cover basically does the same?). A C60X also has the exhaust muffler very close to the gas tank with a heat shield in between. When looking at your first picture, I think the sheet metal cover around the chore horse extends about 4inch from the edge of the fender....hard to see, but it even looks like the originel fender is still there, but it was enlarged along two sides.. Also looks like something is fastened to that third hole in the side of the cab frame....just under the door. What are these holes for anyway....I think they can be seen on all cab13's???? Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle Last edited by Alex van de Wetering; 24-11-15 at 22:29. |
![]() |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Chorehorse question. | Jordan Baker | The Wireless Forum | 63 | 13-01-22 01:16 |
Chorehorse Generators | Neil Ashley | WW2 Military History & Equipment | 5 | 23-07-15 14:27 |
Chorehorse manual on e-bay | Tony Smith | For Sale Or Wanted | 3 | 06-05-07 12:55 |
Chorehorse funnel | chris vickery | For Sale Or Wanted | 4 | 28-02-06 20:57 |
Chorehorse generators | Colin R | The Softskin Forum | 9 | 18-12-05 22:56 |