MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Restoration Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 03-04-18, 23:25
Alex van de Wetering Alex van de Wetering is offline
Moderator
 
Join Date: Mar 2003
Location: Hoofddorp, The Netherlands
Posts: 2,767
Default

EP doesn't necessarily mean it's not compatible with yellow metals! I recently bought "Penrite Mild EP Gear oil" for my Chev steering box. It's safe to use with yellow metals. The C8 steering box has a washer and a bushing in brass. The box still leaks though.....so I am now also looking at the 0 or 00 grease, which is what is used in hydraulic systems on trucks here.....I wonder, is it safe for use with yellow metals?

https://www.penriteoil.com.au/produc...ar-oil-sae-110

Alex
__________________
Chevrolet C8 cab 11 FFW
BSA Folding Bicycle
Reply With Quote
  #2  
Old 04-04-18, 02:53
Wayne Hingley's Avatar
Wayne Hingley Wayne Hingley is offline
Registered User
 
Join Date: Aug 2015
Location: Water Valley, Alberta
Posts: 741
Default

Quote:
Originally Posted by Alex van de Wetering View Post
EP doesn't necessarily mean it's not compatible with yellow metals!
You are correct Alex. There are several specialty oils with EP additive packs that are yellow metal "friendly".

Les: I have decided to use Royal Purple MaxGear 75w90. It is available through Canadian Tire.

Below is some info from their website:
Max Gear is recommended for use in truck and automotive front or rear differentials, manual transmissions and lower gear units of marine engines that specify use of an API GL-5 or GL-4 fluid. It is non-corrosive to soft yellow metals (brass, bronze, copper, etc.) and synchronizer safe.
__________________
1953 M37 CDN
1953 M38A1 CDN
1967 M38A1 CDN2
Reply With Quote
  #3  
Old 04-04-18, 03:42
Les Kovacs Les Kovacs is offline
Registered User
 
Join Date: Jun 2017
Location: Toronto, Canada
Posts: 137
Default Trans Oil

Thanks Wayne....its now a matter of price....if the Royal Purple product is cheaper than the Redline MT90 I will switch.

Regards,

lesk
Reply With Quote
  #4  
Old 22-09-19, 02:19
Jacques Reed Jacques Reed is offline
VMVC
 
Join Date: Jul 2012
Location: Victoria Australia
Posts: 864
Default GL-4 and GL-5 Gear oil for Ford CMP Trucks

As I am about to swap the gears from one transmission case to another on my Ford F15-A I thought it would be a good time to revisit the type of gear oil to use.
After reading this thread I started hunting around on the net for more info. A lot of info that I read about EP additives to gear oil dealt with damage to bronze synchronizers in synchromesh transmissions or bronze worm gears.

In a Ford CMP truck with a non-synchro transmission my main concern however is possible deterioration caused by those additives to the reverse slider gear bronze bushing and the bronze thrust washers in the end gears in the differentials

Extreme pressure rating GL-4 gear oils have about half the quantity of buffered sulphur phosphate EP additives as GL-5 rated oil so is less harmful to yellow metal. As the rating indicates however, GL-4 Extreme pressure protection of gears is less than GL-5 rating.

The next question: Is GL-4 rated 80W-90 gear oil equivalent to, or even better, than the wartime SAE 90 gear oil as far as gear tooth protection goes? If so only GL-4 rated gear oil seems the obvious choice.

Ford gives a spec in their Special Pattern Vehicles manual as Ford spec MC-568A and call it “Extreme Pressure Gear Oil”. Haven’t been able to find a copy of it. It would probably be difficult to relate it to modern extreme pressure ratings anyway.

I have been using Castrol EPX 80W-90 in my CMP truck but it is GL-5 rated so it would have double the yellow metal damaging EP additive compared to a GL-4 gear oil. I found 3 suppliers of only GL-4 rated gear oils in Australia. Penrite, Hi-Tec, and Shell make them and market them here.

On the positive side, the reverse slider gear bushing seems fine even after being immersed in GL-5 oil for 10 years but then again I cannot see micron size damage! Hopefully ditto for the end gear thrust washers.

Any ideas on the subject gratefully received.

Have attached the link to the paper written by Richard Widman a Chevy Corvair enthusiast and a link to a Machinery Lubrication article on EP additives. Both are very informative on this subject.
https://www.widman.biz/uploads/Transaxle_oil.pdf
https://www.machinerylubrication.com...itives-effects
__________________
F15-A 1942 Battery Staff

Jacques Reed
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
For Sale: GM AFV transmission RichCam For Sale Or Wanted 3 02-10-16 19:34
Transmission barriefield-brian For Sale Or Wanted 4 27-10-11 03:03
Transmission oil Mk2/3 Ferret Arlon Bauer The Armour Forum 3 09-05-11 01:47
t-16 transmission 9th field company The Carrier Forum 2 27-04-09 08:33
Transmission Darren The Carrier Forum 1 01-07-04 14:52


All times are GMT +2. The time now is 01:37.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016