R975 Radial engines

[Bob Phillips]

Cylinders- I was prompted to provide this information by an internet photo of a C4 engine that appears to have been rebuilt using -46 cylinders. This seems like a great idea given the scarcity and high prices of C4 cylinders. Hopefully one of the forum readers will recognize the picture and provide details on this rebuild. I assume it will require custom baffles around the cylinders.

C4-46cyls.jpg r975-46cyl.jpg

[Hanno Spoelstra]

Hello Bob,

Over a year ago I came across pictures of a Continental R-975-46A radial engine for sale for not too silly money. I too wondered about the interchangeability of parts, or even a complete engine swap into a M4 Medium tank or related AFV.

Thanks for offering some insight into the detail differences.

Hanno

PS: Here's what I found about about it:

Continental R-975-46A radial: from aero, to tank, to aero engine

Aircraft variant of the Continental R-975. This is the -46A version as used post-WW2 in the Piasecki PV-18 (Navy HUP-3 Retriever, Army H-25A Army Mule) helicopter. It was offered for sale on the Antique Aircraft Parts Exchange FB group, and shared here as it may be of interest to Sherman tank restorers. While originally a Wright design, during WW2 Continental built more R-975's under licence for tanks than Wright did for aircraft (> 53,000 vs. >7,000). After the war, Wright showed no interest in continuing to manufacture the R-975. Continental then introduced its own R-975 version for aircraft, the R9-A. It was basically similar to other R-975 engines, and its compression ratio and supercharger gear ratio were unchanged from the R-975E-3, other improvements in the R9-A allowed it to achieve 525 hp (391 kW) for takeoff, surpassing any Wright version. A military version, the R-975-46, could reach 550 hp (410 kW), and was used in Piasecki's HUP Retriever and H-25 Army Mule helicopters. Continental's production of R-975 engines continued into the 1950s.

16143329_1229046150507700_8307036516151579028_n.jpg 16299003_1229046143841034_5686256705943836334_n.jpg 16174946_1229046147174367_2074506135361185057_n.jpg

Power to the HUP-1, HUP-2 and HUP-3 helicopters is supplied by Continental R-975-42, R-975-46 or R-975-46A air-cooled, nine cylinder radial engines. These were based on the Wright-designed tank engine.

The engine is located within the fuselage aft of the fuel cell and firewall. It simultaneously drives two three-bladed rotors through drive shafts and reduction transmissions. The rotor blades of the HUP-2 are of either wood or metal (later versions) construction.
16300067_1229070160505299_1017659345989160425_o.jpg

Continental R-975-42 as used in the Piasecki PV-18 (Navy HUP-2, later UH-25 Retriever)
16299903_1229079077171074_1047669078119215567_o.jpg

[David Herbert]

There were a number of prototype and very low volume vehicles built with R975 engines. The most obvious being the original M8 High speed tractor (R975D4) and some of the very high mobility 8 x 8 trucks by Corbitt (T33 and T33E1)(R975C4). The fan in Bob's post #12 is a design that I have not seen before, with the blades braced to each other and the exhaust looks as if it has the outlets very low down compared to WW2 applications that had them right at the top or half way down each side.

One of the significant improvements with C4 cylinders was that the cooling fins were made much bigger with bigger gaps between them as the very fine fins on the EC2/C1 and presumably the -46 engines clog up with dust in tank applications.

David