How To: C15a Wire-3 restoration

[Phil Waterman]

Originally Posted by Jordan Baker

.....

Phil, any chance on some pictures of where the fuel line was run in your C8a from the fuel filter to the fuel pump

Hi Jordan


Would you believe out 5000+ photos from the HUP restoration I don't have a good photo of the fuel line routing. It is just one of those hard things to get a clear shot. Was hoping I'd taken some shots with the fuel system mounted to the chassis before I lowered the body back in position but apparently that's something I missed. So here are the two best shots I could find.



My HUP has a solid line from the chassis to the fuel pump but I think it should be a rubber flex line. Memory is telling me there is a service bulletin about changing the fuel line will have to look through them and see if I can find it.


Fuel Line Route .jpg


Cheers Phil
Fuel Line route 1.jpg

[Jordan Baker]

Phil, thanks for the extra pictures. I totally understand about not having certain pictures.

[Bob Carriere]

Hi Jordan

With the flex of the cab 13 anbd tyhe CMP frame flex lines are good insurance.

Doesn't matter what angle and how many pictures you take you will always find a spot you missed....

From what I have of what is left that is deemed possibly original the selection valve had three flex line in and out ..... and some of the frame filters had flex lines,,,,, and there was always a flex line entering the fuel pump with the hard line clipped to the frame and on to the filter. So you are only critical at the pump just replace the short piece. the out put of the pump can be hard line as it is clipped to the water/radiator elbow .....and therefore moves with the engine block.

One line strangely enough that is subjected to engine torque yet has no rubber joints is the steel steam line from the rear of the block to the radiator neck or tank.......

[Grant Bowker]

Bob,
Are you sure there isn't a piece of rubber hose between the steam line and the radiator? (forward of the steel support bracket at the front of the block)
I have one on my C15A and the steam line and radiator fitting don't come even close to lining up without something to make the curve. My steam line and support were copied from what were represented as original parts and the radiator is original (but recored) so the space between radiator fitting and steam tube on my truck should be close to original layout.

[Bob Carriere]

On two of our seemingly original cab 12 the line is solid and runs directly to the filler neck of the radiator where it connects to a brass fitting. The pipe has a tar impregnated loose cover similar to what is used for electrical wiring.

When the radiator shop redid my radiator core they installed a brass threaded connector directly in the rad tank and soldered shut the opening at the bottom of the neck...... they said it would be stronger....I did not bother to argue about it.....and it does work nicely.

Maybe designers got wise with the cab 13 .

Cheers

[Jordan Baker]

A whole lot of parts for a simple antenna mount. Nearly finished the building of this unit.

[Jordan Baker]

I also just got a nice delivery this evening. Newly made side light socket bodies.

[Jordan Baker]

Antenna mounts all painted and the last 5 large bins are all finished with construction and ready to go to the sandblasters this evening.

[Chris Suslowicz]

Originally Posted by Jordan Baker

A whole lot of parts for a simple antenna mount. Nearly finished the building of this unit.

I don't think that is in any way a 'simple' antenna mount.

It looks to be a modification of the original "Aerial Base No.1" mounting (used with the Wireless Set No.11) where there was a tension spring to hold the insulator itself in the "cup" of the mounting. This was then modified later by adding the square adapter and flat plate on top to take Aerial Base No.8 (and later No.10) when the Wireless Set No.19 replaced the earlier set. The 7-hole (for the six mounting bolts and central feed cable) mounting that was introduced with Aerial Base No.8 has remained the standard to the present day, nearly 80 years after introduction.)

Chris.

[Jordan Baker]

I agree Chris. It’s very complicated. It was originally done for the 11set. In one of the original photos there is what appears to be an 11set mounted in the truck. Or at least the charging board for the 11set. The Mk1* Carrier and Otter were also made to be able to fit the 11set or 19set.