Chevrolet coolant condensor can

[Mike Cecil]

Looks very similar to that used on the Ford-MH 'Car, Scout, Aust' ie the Dingo. It was mounted on the right wall of the engine compartment. I had one, the difference being the legs were shorter and there was no red stencil.

So perhaps a commercially available part with many applications?

Mike

[Lynn Eades]

So, A contract that GM won to provide tanks for Jeeps, for example?

[Hanno Spoelstra]

Originally Posted by Mike Cecil

So perhaps a commercially available part with many applications?

I'd say yes.

Seller’s description:

This is an original Chevrolet accessory radiator overflow condenser tank for various 1930's-40's Chevrolet car or truck applications. This condenser is in good condition with no large dents or major rust damage. There is minimal surface wear considering it has been used. There are no unintended bends to the mounting arms and nothing appears to be modified on this part. The final picture shows the Chevrolet emblem and safety/operating instructions. The canister measures 10" long and 4-1/4" in diameter and has original fittings in-tact with no damage. This is a great add-on to set your car or truck apart from others at the car shows and cruises.

So the CMP radiator overflow tank was an off the shelf design, adapted dimensionally to make it fit the CMP trucks.

[Grant Bowker]

The coolant overflow recovery tank described above sold for US$225.50


I wonder if this one will go as high? https://www.ebay.ca/itm/1937-thru-54...K/293150321386 I suspect it may be a repro as the listing says it is the last one, with 10 already sold. The listing also references "Counterpart Automotive" part # 41-8255.


From a post at http://67-72chevytrucks.com/vboard/s...d.php?t=536752 "
Counterpart is the wholesale side of Car & Truck shop out of orange, CA. They are importers of many truck parts and wholesale to a lot of retailers."
Sure enough, the tank can be found at https://issuu.com/truckandcarshop/docs/ts_47-59_13_web

[Hanno Spoelstra]

Nice find, Grant!

Now let's ask this company to do a run of the smaller CMP condensor cans...

[Grant Bowker]

I measure the CMP can as very close to 6-3/4" diameter (including the rim, just because that is the easier dimension to take) and very close to 8-1/2" height (again including the rims) - so shorter and fatter than what the commercial reproductions. Getting into the detail, there is a difference in the water connection (as opposed to the central vent tube) on the bottom of the can between the cans made to mount on the cab side and those made to mount under the floor. In the attached photos, the underfloor mounted tank(s) is the one with the water connection on the side opposite the mounting straps so that the connection is (almost) at the low point of the tank whereas for the tank ponted on the side of the cab, the connection is closest to the cab and less exposed to damege. The can with dark green paint is the side of cab version, the others are the under floor version. The commercial reproduction construction more closely resembles the side of cab mounted CMP cans (both appear to have been mounted vertically rather than on an angle under the floor).

If only one version were to be reproduced, the one for use under the floor would probably be better (less volume of water sitting in the can at rest).
Also attached is a page on the condensor can from Convoy Magazine (Years ago, I did ask Marc Montgomery if it was acceptable to share the content of Convoy. He said it was OK.) The Convoy Magazine version is the under floor mount version.

There have been a number of discussions of the condensor/overflow/expansion tank/can over the years. One at http://www.mapleleafup.net/forums/sh...9647#post49647 included a drawing from Bruce Parker, attached to try to group information. Bruce's is the side of cab version.

CMP condensor can bottom.jpg CMP condensor can top.jpg

CMP Condensor can from Convoy Mag No.2.jpg chev overflow can.jpg

[Mike Cecil]

If you wisk that info down to your local sheet metal shop, they should be able to provide a quotation to manufacture a small quantity.

In Australia, I'd be talking with Cecil & Co in Bayswater, Victoria, who have the necessary rollers, Philidelphia seamer, bottom edge rollers, and soldering setup - the only difficulty I can see is the pressed dimple in the top.

It is a straight-forward can-making process with a few quirks in terms of soldering in the tubes and the pressed dimple in the top.

Mike

[8threcce]

Originally Posted by Grant Bowker

I measure the CMP can as very close to 6-3/4" diameter (including the rim, just because that is the easier dimension to take) and very close to 8-1/2" height (again including the rims) - so shorter and fatter than what the commercial reproductions. Getting into the detail, there is a difference in the water connection (as opposed to the central vent tube) on the bottom of the can between the cans made to mount on the cab side and those made to mount under the floor. In the attached photos, the underfloor mounted tank(s) is the one with the water connection on the side opposite the mounting straps so that the connection is (almost) at the low point of the tank whereas for the tank ponted on the side of the cab, the connection is closest to the cab and less exposed to damege. The can with dark green paint is the side of cab version, the others are the under floor version. The commercial reproduction construction more closely resembles the side of cab mounted CMP cans (both appear to have been mounted vertically rather than on an angle under the floor).

If only one version were to be reproduced, the one for use under the floor would probably be better (less volume of water sitting in the can at rest).
Also attached is a page on the condensor can from Convoy Magazine (Years ago, I did ask Marc Montgomery if it was acceptable to share the content of Convoy. He said it was OK.) The Convoy Magazine version is the under floor mount version.

There have been a number of discussions of the condensor/overflow/expansion tank/can over the years. One at http://www.mapleleafup.net/forums/sh...9647#post49647 included a drawing from Bruce Parker, attached to try to group information. Bruce's is the side of cab version.

Attachment 115471 Attachment 115470

Attachment 115472 Attachment 115473

Sorry for my late reaction on this thread since I'm now confronted with the search of a condensor.
Are there any pictures that show how the condensor is hooked up to the radiator??