MLU FORUM  

Go Back   MLU FORUM > 'B' ECHELON > The Sergeants' Mess

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 04-11-21, 16:01
maple_leaf_eh maple_leaf_eh is offline
Terry Warner
 
Join Date: Mar 2004
Location: Shouting at clouds
Posts: 3,081
Default How do I cut 1/2" rubber mats?

Gents:

Winter is approaching here in Canad'er and we've had the first hard frosts. My front steps are painted boards over concrete blocks. (The company that made the blocks is long out of business, and the lumber yard where I once found some, now sells furniture and has a housing development in the back yard.)

To avoid slipping on the steps, I found some stair treads made from ground-up car tires. But they need to be deeper. How can I cut 3" wide strips off another tread? Table saw?
__________________
Terry Warner

- 74-????? M151A2
- 70-08876 M38A1
- 53-71233 M100CDN trailer

Beware! The Green Disease walks among us!
Reply With Quote
  #2  
Old 04-11-21, 17:13
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

Best thing I have found for cutting rubber is a straight edge and razor knife. That is assuming it does not have the little pieces of steel belting in them. Cut once, bend it a bit, cut again, and repeat until it is done. And of course, use a brand new razor blade.
Anything like a saw or grinder disc is going to make an incredible amount of dust or clog up as the heat turns the rubber to goo. Perhaps running water on the cut like you would with cement might help.
Reply With Quote
  #3  
Old 04-11-21, 18:04
Mike Cecil Mike Cecil is offline
Registered User
 
Join Date: Jun 2006
Location: Cody, Wyoming, USA
Posts: 2,365
Default

I recently had to cut some 6.00-16 tyres from wheel rims. I used a Sawzall with a demolition-toothed blade to cut out a big 'U' in the rubber down to the steel wires/belt, then an angle grinder with a metal cutting blade to nip through the steel part once I prised it just clear of the wheel rim using two large screwdrivers. Worked well: some mess of rubber granules from the saw, and a little acrid smoke from the grinder, otherwise no problem at all.

Unless you want a clean edge, the Sawzall worked well.

I've used a non-slip tape on steps and it works really well.

Like this: https://www.amazon.com/Slip-Guard-No.../dp/B01HQXNBHW

Mike

Last edited by Mike Cecil; 05-11-21 at 03:31.
Reply With Quote
  #4  
Old 05-11-21, 01:50
maple_leaf_eh maple_leaf_eh is offline
Terry Warner
 
Join Date: Mar 2004
Location: Shouting at clouds
Posts: 3,081
Default

I have cut scrap tires with a reciprocating saw and a grinder, and was unimpressed by the results.

I may use two straight edges clamped down, and just get going with handsaws and knives. Whatever works.
__________________
Terry Warner

- 74-????? M151A2
- 70-08876 M38A1
- 53-71233 M100CDN trailer

Beware! The Green Disease walks among us!
Reply With Quote
  #5  
Old 05-11-21, 03:24
r.morrison r.morrison is offline
Registered User
 
Join Date: Nov 2007
Location: vancouver b.c.
Posts: 814
Default Man's Answer to Everything!!!

Number 1: I agree with Rob. You'll go through a few blades cuz he's right about the new blades. Number 2: The smart guy would go to PRINCESS AUTO..."man's answer to every problem in life" and buy the Non Slip Tread that they sell in a roll and you can cut to any length. And it goes on sale once in a while. You can probably order it on line.
My 2 cents.....Robert
Reply With Quote
  #6  
Old 05-11-21, 16:26
Jesse Browning Jesse Browning is offline
Registered User
 
Join Date: Sep 2009
Location: Waterloo
Posts: 366
Default

Rubber, unless it has the formed surface like a tire is extremely slippery. Even rough rubber will be slippery if its in the shade and moss grows on it. The house I moved to had shredded rubber mats. They were slick as banana peels.
Reply With Quote
  #7  
Old 22-10-22, 09:15
REL REL is offline
Robert
 
Join Date: Mar 2008
Location: Vancouver Island
Posts: 37
Default

It's surprising what a water-jet machine can cut, and very precisely too. Some even do bevels.
Reply With Quote
  #8  
Old 22-10-22, 12:19
Matthew P Matthew P is offline
Registered User
 
Join Date: Jul 2018
Location: West Virginia, USA
Posts: 199
Default

I've done tires (7.50x20 for a trailer next time I'll just outsource the removal to the tire shop, paint the rims and come back...) and stall mats for horses. Those are circa 3/4" thick. You're two options, and each work in their own way is the utility knife or a reciprocating saw. The utility knife seems daunting at first and you think it'll take forever, but you'll be surprised how fast you can cut the rubber. The other way is to use a sawsall, jig-saw or similar at slow speed. As mentioned previously heat is your enemy here.

Matt
Reply With Quote
  #9  
Old 23-10-22, 01:03
jack neville jack neville is offline
Registered User
 
Join Date: Jun 2010
Location: leopold, victoria
Posts: 1,019
Default

If you are cutting rubber with a blade use plenty of soapy water .
__________________
1943 Willys MB
Willys Trailer
1941 Fordson WOT 2H
1941 Fordson WOT 2H (Unrestored)
194? Fordson WOT 2D (Unrestored)
1939 Ford 1 ton utility (Undergoing restoration)
1940 Ford 1 ton utility (Unrestored)
1941 Ford 1 ton utility (Unrestored)
BSA folding bicycle
BSA folding bicycle
1941 Ford/Marmon Herrington 3A gun tractor
1941 Ford/Marmon Herrington 3 gun tractor (Unrestored)
1941 Diamond T 969 (Unrestored)
Wiles Junior Cooker x 2
Reply With Quote
  #10  
Old 23-10-22, 21:30
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

I have had carrier radiator mounts water cut, but in this case, I would look for a tyre grooving tool to hot cut the pieces. Just a suggestion, as I have no experience. Otherwise back to what Rob said.
What about stapling some chicken netting over the steps for grip? does that work in "cold and wet"
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #11  
Old 24-10-22, 04:08
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

Quote:
Originally Posted by Lynn Eades View Post
does that work in "cold and wet"

The term "cold" is subjective. Terry lives in Ottawa. Their idea of cold is if the water is close to freezing. Where I am at, cold is if you toss a cup of hot water in the air, and it freezes before it hits the ground.
Reply With Quote
  #12  
Old 24-10-22, 07:26
Tony Smith's Avatar
Tony Smith Tony Smith is offline
No1, Mk 2** (I'm back!)
 
Join Date: Feb 2003
Location: Lithgow, NSW, Australia
Posts: 5,042
Default

So no need for Chicken netting, as the Chickens don't dare go outside anyway?
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should!
Reply With Quote
  #13  
Old 25-10-22, 10:44
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

So, if you find one outside, you just tap it. Then you'll have frozen chicken pieces.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Article by Rick Forys - "Armor-Zona", April/May 2019 issue of "History in Motion" Jim Price The Softskin Forum 2 04-05-19 01:22
Rubber Mike Kelly Parts/Sources/Prices 0 02-11-15 10:00
New Book: "Amazing Airmen": "Canadian Flyers In The Second World War" RAF21 WW2 Military History & Equipment 1 27-11-09 03:30
A "Duck Tale"--Story and photos of historic "swim-in" jagjetta Military Shows & Events 1 14-09-07 03:26
"Cinderella Army" and "Fields of Fire" Bob Potter WW2 Military History & Equipment 1 06-06-07 23:55


All times are GMT +2. The time now is 13:39.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016