MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > Post-war Military Vehicles

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 03-07-16, 04:53
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default Ferret erratic knocking from left hand side front.

We drove a Ferret about 15 miles to a Canada Day parade with no problem but during the parade, it started to knock once loudly when braking to a standstill. This was coming from LHS front, outside the hull. By the end of the parade, the knocking was much worse. Multiple knocks, erratic, not related to wheel speed, like someone hitting the outside of the hull with a hammer, and only when drivetrain was loaded. I could feel the impact on the hull from the inside. When coasting downhill, i.e. unloaded, there was no knocking.

No obvious loose suspension parts. Pulled the brake drum off and no breakage or loose parts.

For info, I dismantled the hub a while back to replace the brake backing plate.

Anyone experienced this ?

Malcolm
Reply With Quote
  #2  
Old 03-07-16, 11:30
Robin Craig's Avatar
Robin Craig Robin Craig is offline
Registered User
 
Join Date: Jan 2006
Location: Near Kingston, ON, Canada
Posts: 2,153
Default

It might sound like one thing but may be another.

I had a bevel box input bearing go (long story) that sounded like that as the input flange thwacked around as it destroyed itself.

I am sure it will reveal itself shortly in a pile of expensive broken bits
__________________
Robin Craig

Home of the Maple Leaf Adapter
2 Canadian Mk1 Ferrets
Kawasaki KLR250 CFR 95-10908 ex PPCLI
Canadair CL70 CFR 58-91588
Armstrong MT500 serial CFR 86-78530
Two Canam 250s
Land Rover S3 Commanders Caravan Carawagon 16 GN 07
Trailer Cargo 3/4 T 2WHD 38 GJ 62
Reply With Quote
  #3  
Old 03-07-16, 11:36
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,634
Default

Hi Malcolm,
If this is what I think it is, I have dealt with it on numerous occasions, with Ferret as well a Saracen, Stalwart, Fox, etc. It could well be a metal deposit between the a tracta fork and knuckle on an outer tracta joint. Due to localised heat a pit occurs on one part and a deposit on the other and when driving in a straight line this does not create any or much noise, until you steer off centre and the pip is then not aligned with the pit and then knocking occurs. What you could do is jack up both wheels one side and get someone to turn the rear one and watch the front wheel, if you have the steering slightly one way you may notice the wheel kick as it turns. Depending on how big an area is damaged it is permissible to stone down the damaged to regain working clearance, the pit actually serves as an oil retainer, just depends how bad it is.

regards Richard
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #4  
Old 04-07-16, 00:58
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Quote:
Originally Posted by Richard Farrant View Post
Hi Malcolm,
If this is what I think it is, I have dealt with it on numerous occasions, with Ferret as well a Saracen, Stalwart, Fox, etc. It could well be a metal deposit between the a tracta fork and knuckle on an outer tracta joint. Due to localised heat a pit occurs on one part and a deposit on the other and when driving in a straight line this does not create any or much noise, until you steer off centre and the pip is then not aligned with the pit and then knocking occurs. What you could do is jack up both wheels one side and get someone to turn the rear one and watch the front wheel, if you have the steering slightly one way you may notice the wheel kick as it turns. Depending on how big an area is damaged it is permissible to stone down the damaged to regain working clearance, the pit actually serves as an oil retainer, just depends how bad it is.

regards Richard
Richard,
This noise happens when going in a straight line and only when the drivetrain is loaded. Steering left or right doesn't seem to make any difference. And it's not a regular click-click while turning like I have heard from pitting of CV joint bearing surfaces. Sounds more like what Robin is describing.

Malcolm
Reply With Quote
  #5  
Old 04-07-16, 04:45
Grant Hopkins Grant Hopkins is offline
Registered User
 
Join Date: Aug 2015
Location: Sidney, BC Canada
Posts: 50
Default

Sounds familiar, I had a bevel box go on my Ferret in the RH rear position. It started to clunk and got rapidly worse on the way back to park it, it even locked up a couple times and I had to move it in reverse briefly to unlock and continue ahead. I wouldn't recommend driving it until you figure out exactly what is wrong, it could become a very heavy and difficult to move roadblock.
Reply With Quote
  #6  
Old 04-07-16, 19:27
45jim 45jim is offline
Registered User
 
Join Date: May 2010
Location: Woodstock, ON
Posts: 154
Default Ferret noise

Insect suspension ball joints, steering joints and wheel nuts to ensure tight and serviceable. If all OK, disconnect the driveshaft from the transfer box to the suspect bevel box. Drive the Ferret around a parking lot to see if the noise is related just to the suspect wheel station. If noise stops suspect u-joint on driveshaft or bearing on bevel box input or transfer box output or the transfer box itself. If still knocking from the wheel station you know your problem is the wheel station itself, remove the outer hub cover and remove the sun gear and replace the cover. Move the vehicle carefully in a straight line. The tracta joint and bevel box will be disengaged and should remain stationary. If the noise goes away your problem is there and you will have to remove the wheel station to further diagnose. If the noise is still there you will have to dig further into the hub itself as this may be a bearing failure or a broken gear in the reduction hub.
Reply With Quote
  #7  
Old 04-07-16, 20:49
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Quote:
Originally Posted by Grant Hopkins View Post
Sounds familiar, I had a bevel box go on my Ferret in the RH rear position. It started to clunk and got rapidly worse on the way back to park it, it even locked up a couple times and I had to move it in reverse briefly to unlock and continue ahead. I wouldn't recommend driving it until you figure out exactly what is wrong, it could become a very heavy and difficult to move roadblock.
Grant, what had actually failed in the bevel box?

Malcolm
Reply With Quote
  #8  
Old 04-07-16, 21:02
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Quote:
Originally Posted by Robin Craig View Post
It might sound like one thing but may be another.

I had a bevel box input bearing go (long story) that sounded like that as the input flange thwacked around as it destroyed itself.

I am sure it will reveal itself shortly in a pile of expensive broken bits
Robin,
Did you hear the input bearing get noisy before the flange thwacking started? Or did the bearing just collapse, like they do if the cage suddenly breaks up?

Because in our case, the front left wheel station was running smoothly and quiet until the knocking started quite suddenly.

It's off the road until this is fixed, which may be take a while due to other priorities.

Malcolm
Reply With Quote
  #9  
Old 04-07-16, 21:04
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Quote:
Originally Posted by 45jim View Post
Insect suspension ball joints, steering joints and wheel nuts to ensure tight and serviceable. If all OK, disconnect the driveshaft from the transfer box to the suspect bevel box. Drive the Ferret around a parking lot to see if the noise is related just to the suspect wheel station. If noise stops suspect u-joint on driveshaft or bearing on bevel box input or transfer box output or the transfer box itself. If still knocking from the wheel station you know your problem is the wheel station itself, remove the outer hub cover and remove the sun gear and replace the cover. Move the vehicle carefully in a straight line. The tracta joint and bevel box will be disengaged and should remain stationary. If the noise goes away your problem is there and you will have to remove the wheel station to further diagnose. If the noise is still there you will have to dig further into the hub itself as this may be a bearing failure or a broken gear in the reduction hub.
Thanks, Jim. Good logical diagnosis. We've inspected brakes and suspension so far. All looks good.

Malcolm
Reply With Quote
  #10  
Old 05-07-16, 11:39
Robin Craig's Avatar
Robin Craig Robin Craig is offline
Registered User
 
Join Date: Jan 2006
Location: Near Kingston, ON, Canada
Posts: 2,153
Default

Malcolm the honest answer is I can not recall the sequence of noises during the failure.

As Jim said raise that side off the ground and you should quite quickly be able to diagnose the troublesome component by disconnecting various items in the drive train.

The cause of failure on the bevel box was a very nicely painted over breather for the bevel box. It had several layers of paint, it is something I warn about often and loudly to new and keen Ferret owners.
__________________
Robin Craig

Home of the Maple Leaf Adapter
2 Canadian Mk1 Ferrets
Kawasaki KLR250 CFR 95-10908 ex PPCLI
Canadair CL70 CFR 58-91588
Armstrong MT500 serial CFR 86-78530
Two Canam 250s
Land Rover S3 Commanders Caravan Carawagon 16 GN 07
Trailer Cargo 3/4 T 2WHD 38 GJ 62
Reply With Quote
  #11  
Old 06-07-16, 06:49
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Robin,
Why would a plugged breather cause such a catastrophic failure?

Malcolm
Reply With Quote
  #12  
Old 06-07-16, 10:09
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,634
Default

Quote:
Originally Posted by Malcolm Towrie View Post
Robin,
Why would a plugged breather cause such a catastrophic failure?

Malcolm
Malcolm,
Failures are often due to lack of oil or low levels. With a blocked breather the pressure build up could force oil out of the bevelbox / inner tracta via the cork seal around the inner tracta housing, also it could well pass the seals in the challis and overfill the outer tracta and hub, seen this quite often. It pays to check the levels frequently.
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #13  
Old 06-07-16, 21:50
Robin Craig's Avatar
Robin Craig Robin Craig is offline
Registered User
 
Join Date: Jan 2006
Location: Near Kingston, ON, Canada
Posts: 2,153
Default

Malcolm,

Richard eloquently and precisely said what I would have replied.
__________________
Robin Craig

Home of the Maple Leaf Adapter
2 Canadian Mk1 Ferrets
Kawasaki KLR250 CFR 95-10908 ex PPCLI
Canadair CL70 CFR 58-91588
Armstrong MT500 serial CFR 86-78530
Two Canam 250s
Land Rover S3 Commanders Caravan Carawagon 16 GN 07
Trailer Cargo 3/4 T 2WHD 38 GJ 62
Reply With Quote
  #14  
Old 06-07-16, 22:38
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Have you ever used and IR gun to check temps

Hi Guys

Was wondering if any of you have used and IR gun to check the drive train temperature on a Ferret?

On my CMPs I make it a practice to check the drive train of trucks after any drive of length. Using a check sheet I record the different points, transmission, transfer case, brake drums, wheel bearings, etc. If anything is out of line it jumps out pretty quick. The one time I didn't check a +10 F (of norm) wheel bearing temp that was out of line the next time I drove the truck nearly lost a wheel the axle nut keeper had failed.

Would think with a complex drive train like a Ferret you would get a good hold on what normal temps should be.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #15  
Old 09-07-16, 02:41
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Good point, Phil. It's a lot easier to reach round the tire with the gun than crawling in there. A great way of picking up an oil level getting dangerously low.

But be careful with those cheapy IR cameras with the laser sight. They will read dangerously low if not used properly. This is because the area of the so-called "spot" seen by the camera gets bigger the further away the object is. If you are looking at a small hot object 10' away with a cool background, the gun will give you the average of the 2' diameter circle it is seeing at that distance, even though the laser dot is right on the hot object. So get as close as you can.

Malcolm
Reply With Quote
  #16  
Old 30-08-16, 03:39
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Update: it was the inner tracta joint that partially seized due to low oil level. Our mistake, obviously. The long drive generated enough heat in the joint to blue the steel. As Richard said, the ensuing galling created high spots on one face and low spots on the mating face. So under load they locked together and prevented the faces sliding. The inner joint only pivots vertically to accommodate suspension movement up and down, so it didn't knock when turning, just when loaded.

The tracta joints look particularly susceptible to low oil level because their small diameter means they loose the oil splash sooner as oil level drops.

Click image for larger version

Name:	DSC02822.jpg
Views:	6
Size:	206.6 KB
ID:	84748

Another question: we have no spare left front/right rear bevel box so I need to steal parts from some spare right front/left rear boxes we have. But the bevel gear design in the spares is significantly different. The bevel gear is one piece, incorporating the hub, unlike the original gear which has the hub riveted to the gear. Also the tapered roller bearing between the tracta joint and the bevel gear is much larger than the original. See the photo of a good spare below. Are they interchangeable?

Click image for larger version

Name:	DSC02863.jpg
Views:	2
Size:	132.2 KB
ID:	84756

It looks a bit laborious setting up the bearing preloads, lash, and tooth contact without the special tooling in the manual.

Malcolm
Reply With Quote
  #17  
Old 30-08-16, 05:49
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Can you not dress up the old one Malcolm?
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #18  
Old 30-08-16, 06:03
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Looked a bit dodgy, Lynn. What with the bluing of the joint due to overheating and the quite bad galling. I'd rather replace it.
Malcolm

Click image for larger version

Name:	DSC02837.jpg
Views:	1
Size:	99.1 KB
ID:	84757
Reply With Quote
  #19  
Old 30-08-16, 09:41
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,634
Default

Hi Malcolm,
I was pretty sure it would be a tracta. The problem is when topping up the oil, people often think that when the oil globs out of the hole as soon as they start filling, that it is up to level, whereas it is air pushing the oil back out of the horizontal level tube. The trick is to use a hand pump of low volume output with a small pipe that can be inserted right up the tube and thus letting air out as you fill, this is useful on other top up points as well. I have a converted grease pump which have been using for 20 years on many type of vehicles without issues.

regards, Richard
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #20  
Old 30-08-16, 23:21
motto motto is offline
Registered User
 
Join Date: Apr 2010
Location: Woodend,Victoria,Australia
Posts: 1,068
Default

Having little experience with tracta joints I may be speaking out of turn but in general terms the importance of lubrication cannot be overstated. The joint in question appears to have been operated bone dry and simply filling the housing to the correct level with the correct oil may have solved the problem despite the appearance of the parts. I would have no hesitation in following Richard's earlier suggestion to remove the high spots and put it back to work. (Though he hadn't seen the damage at that point).
After all, any of the other joints in the vehicle could be almost as bad and you wouldn't know until it started talking to you.

David
__________________
Hell no! I'm not that old!

Last edited by motto; 30-08-16 at 23:50.
Reply With Quote
  #21  
Old 30-08-16, 23:35
Richard Farrant's Avatar
Richard Farrant Richard Farrant is offline
Registered User
 
Join Date: Feb 2003
Location: Kent, England
Posts: 3,634
Default

Quote:
Originally Posted by motto View Post
Having little experience with tracta joints I may be speaking out of turn but in general terms the importance of lubrication cannot be overstated. The joint in question appears to have been operated bone dry and simply filling the housing to the correct level with the correct oil may have solved the problem despite the appearance of the parts. I would have no hesitation in following Richard's suggestion to remove the high spots and put it back to work.

David
Hi David,
It is difficult to judge the surface of the tracta parts in the photo, but when metal transference happened, a pit and a pimple, if it was only a small area, the surface could be stoned smooth and clearance checked and re-used. Our inspection standards (REME) stated that a certain percentage of area could be affected but still used as any small pockets/pits retained oil.

regards Richard
__________________
Richard

1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2
Member of MVT, IMPS, MVG of NSW, KVE and AMVCS
KVE President & KVE News Editor
Reply With Quote
  #22  
Old 31-08-16, 05:31
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

I saw it like David. Clean off the high spots put some lube on the mating components and see how smoothly they move relative to each other When you get it so that it all feels good put it back together.
I would doubt the colouration is serious. You will know when it is a problem,if indeed it becomes a problem. You might get many years out of that Tracta joint. That's why I made the suggestion.
The worlds supply of ferret parts will run out one day.
I may be wrong, but isn't it worth a shot?
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #23  
Old 08-09-16, 03:17
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

I just found these responses. I guess MLU doesn't send an email when people post.

It comes down to a judgement call, doesn't it, and my judgement was the two inner tracta joints and shaft forks in the bevel box were too badly damaged to reuse, and I was lucky enough to have spares so I replaced them.

The bevel box is back together and has been reinstalled in the Ferret.

Malcolm
Reply With Quote
  #24  
Old 08-09-16, 07:39
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Great to hear you have mobile again, Malcolm. As the owner your judgement is tops in my book.
David and I were just offering our advice / opinion, hoping it would help you.

Of course it came with a 100% money back guarantee.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #25  
Old 09-09-16, 03:34
Malcolm Towrie Malcolm Towrie is offline
Registered User
 
Join Date: Aug 2015
Location: Whitby, Ontario, Canada
Posts: 306
Default

Not quite mobile yet, Lynn, but getting there.

So the inner tracta joint is all new, but just to let you know about the outer tracta joint; the hard chrome plating of the hub shaft fork had some pits (due to fatigue spalling, I think), which had caused some galling on the mating tracta joint "ball" (jeez, the part names are complicated). But this damage had not been causing any running problems prior to the inner tracta joint seizing so I happily stoned off the high spots on the joint "ball" and reused the parts.

Now, knowing I have a money back guarantee makes me feel even more confident.

Malcolm
Reply With Quote
  #26  
Old 09-09-16, 07:01
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

We're a helpful lot here Malcolm
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Wanted: left hand escape hatch for Ferret Barry Pobke For Sale Or Wanted 0 10-01-16 05:06
Sold: Land Rover 101 FC Left hand drive (sand colour) Robin Craig For Sale Or Wanted 14 16-11-13 01:55
Wanted: left side pawl bracket .50 bmg Andrew For Sale Or Wanted 0 20-06-13 14:42
Wanted 7/8" NF left hand thread nuts Bruce Parker (RIP) The Restoration Forum 3 09-04-13 18:50
My left hand doesn't know what my right hand is doing cmperry4 The Restoration Forum 5 27-03-05 09:15


All times are GMT +2. The time now is 15:05.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016