MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Carrier Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 24-03-19, 07:55
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default Welding a carrier floor

I have a carrier floor which I hope to repair by welding a strip from one end to the other.
Dose anybody have some proven advise? Has any one here done it before?
If I use a mild steel patch will it weld to the floor? can I Mig it, or should I stick weld it with stainless rods ( I have a Mig and an Arc)
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #2  
Old 24-03-19, 11:25
David Herbert David Herbert is offline
Registered User
 
Join Date: Mar 2010
Location: Ayrshire, Scotland - previously Suffolk
Posts: 547
Default

Mild steel and normal MIG wire will work fine but weld in short runs well spaced apart to keep the heat down.

Also don't be tempted to use thinner steel than the original. If you operate the carrier you will scrape its belly on something sooner or later and if the something is solid it can put a huge force on the belly plate and dent it.

David
Reply With Quote
  #3  
Old 24-03-19, 14:30
Tony Smith's Avatar
Tony Smith Tony Smith is offline
No1, Mk 2** (I'm back!)
 
Join Date: Feb 2003
Location: Lithgow, NSW, Australia
Posts: 5,042
Default

UK, Can, Aus or NZ production?

I know the steel used in the Australian LP Carriers is a local alloy (ABP3) that has very different composition and heat treating to, say, the UK Armour Plate, and as a result the technique and materials (and the quality of the end result) will differ. I believe the NZ steel is also similar to Aus ABP3, and Canadian steel is closer to UK Plate, but may well be different due to the wartime availability of raw materials and production techniques.

But maybe you're working on an NZ LP1 (NZR 6, 21 or 29?? ), which were just Mild Steel and any welding technique will work!
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should!
Reply With Quote
  #4  
Old 24-03-19, 18:37
Andrew Rowe Andrew Rowe is offline
Registered User
 
Join Date: Aug 2012
Location: Manawatu , New Zealand
Posts: 544
Default Welding Technique

Lynn, use mild steel solid core 0.9mm wire with CO2 shielding. This is the most cost effective and best results with no cracking. It will weld any of the armour from any country, and yes use techniques that dissipate the heat from the weld zone, as David has eluded to. One technique is "backstep" welding, where you stop your run from where you last started it , if that makes sense, as it does not allowe heat to keep transferring along the direction of weld. Also use veeing the steel as well for penetration, and gap depending on thickness for sound welds, Cheers Andrew.
__________________
Valentine MkV
Covenanter MkIV
Lynx MKI and MKII
Loyd Carrier / English / Candian / LP.
M3 Stuart
Reply With Quote
  #5  
Old 24-03-19, 19:36
Mike Cecil Mike Cecil is offline
Registered User
 
Join Date: Jun 2006
Location: Cody, Wyoming, USA
Posts: 2,365
Default From the Manual ...

Lynn,

Instructions from the Aust Carrier Workshop Manual for ABP-3 plate repairs.

Mike
Attached Thumbnails
Carrier Repair 1.jpg   Carrier Repair 2.jpg  
Reply With Quote
  #6  
Old 24-03-19, 19:50
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Thank you guys. I will try to follow your accumulated advice. This floor is from a Canadian hull. It is 3mm thick.
As an aside, the NZ Bren has a new floor made from Corten. I am not working on that.
When i tried to weld the div plate from the NZ Bren, it kept cracking, when I used the mig. That was "mild steel" (nothing like mild!) from the ship "Bowen" built in 1901. I ended up using the stick welder, and I can't remember which rods.
Anyhow I'm guessing others have patched a Canadian carrier floor.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #7  
Old 25-03-19, 11:18
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Hi Lynn, I used basic rods 7016 on my British carrier with pretty good results. No preheating, armoured plates to mild steel.
I was surprised how easy it went.
__________________
UCw Mk.III
Reply With Quote
  #8  
Old 25-03-19, 15:59
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default 3 MM thick?

Quote:
Originally Posted by Lynn Eades View Post
Thank you guys. I will try to follow your accumulated advice. This floor is from a Canadian hull. It is 3mm thick.
......

Hi Lynn


3 MM seems thin, check my math guys that would be .11811 inches thick that's less than 1/8 of an inch. Floor plates in CMP cab are thicker than that.


I've welded 1/4 inch diamond plate very successfully with Mig welder using CO2 or CO2-Argon with a 110 volt machine. As suggested weld in short sections to prevent warping. If you can find an old brass kick plate I have had very very good luck using them as a heat sink behind the weld to prevent warping. Brass or copper are good because the weld won't stick to them. If you don't have brass plate I've been using scrap copper pipe just slit it and flatten it out.


Another good heat sink trick is wet toilet paper scrunch up and stuck to the steel about an inch from weld.


Before and after pictures of the repair would be interesting.


Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #9  
Old 25-03-19, 18:50
David Herbert David Herbert is offline
Registered User
 
Join Date: Mar 2010
Location: Ayrshire, Scotland - previously Suffolk
Posts: 547
Default

I agree with all of Phill's comments but copper works much better than brass because of its higher melting point.

I must admit I thought carrier floor was 6mm but have never cut into it to see.

David
Reply With Quote
  #10  
Old 25-03-19, 19:35
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Sorry guys, I was assuming 3mm. It is actually 4mm.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #11  
Old 25-03-19, 21:40
RichardT10829's Avatar
RichardT10829 RichardT10829 is offline
Richard Harrison
 
Join Date: Nov 2008
Location: Cullercoats Newcastle Upon Tyne United Kingdom
Posts: 3,059
Default

Pretty much all been covered, I used mig with good argon shielding mix. Weld an inch then move along say 10" before starting the next inch of weld, the aim as already described is to minimise heat soak into the job.

to add another facet to the job, I stretch my welds on long runs such as this....so weld the inch but before it cools flatten the weld with a hammer (dolly will need to be on the other side) this stops the sheet being pulled as the weld shrinks as it cools, in essence you avoid the issues of the two sheets becoming miss aligned and you putting un necessary tension into the sheets.

its a biggie especially welding aluminium, or aircraft skins which are thinner, but personally I advocate irrespective of metal thickness you do it.

best of luck to you buddy.
__________________
is mos redintegro

__5th Div___46th Div__
1942 Ford Universal Carrier No.3 MkI*
Lower Hull No. 10131
War Department CT54508 (SOLD)
1944 Ford Universal Carrier MkII* (under restoration).
1944 Morris C8 radio body (under restoration).

Last edited by RichardT10829; 26-03-19 at 00:11.
Reply With Quote
  #12  
Old 27-03-19, 00:21
eddy8men eddy8men is offline
AKA Rick Wedlock
 
Join Date: Dec 2009
Location: manchester
Posts: 715
Default

i replaced quite a few patches on my T16 floor using normal mild steel plate and .8mm mig wire. i welded it normally in one run and had no problems.
the only time i got cracking of welds was doing short 1" welds on the 1/2" wading plates. it goes against what everyone else has said but i put it down to not enough heat transfer from the weld to the armour plate. i did a few large plate patches on the side armour with the mig turned up all the way and had no issues as i believe the original armour got hot and took longer to cool down helping to even things out.
__________________
_______________________
1941 mk1 mortar Carrier
1941 Mk1* Carrier
1942 Mk1* Carrier
1943 T16 Carrier
1945 Mk3 Dingo
1941 Mk3 Covenanter
1941 Mk4 Churchill AVRE (now sold)
1944 Mk6 Cromwell (now sold)
1952 Mk3 Centurion
1952 ARV Centurion
1952 ARV Centurion
1953 Mk3 Centurion (breaking)
Reply With Quote
  #13  
Old 28-03-19, 02:20
Stew Robertson Stew Robertson is offline
Staghound
 
Join Date: Feb 2010
Location: Rockwood, ON, Canada
Posts: 268
Default

The floor plate is 10 gauge and can be welded with mig leave a small gap and go at it
Spot it into place and stitch weld it 10 inches apart down the length way easy peasy
Reply With Quote
  #14  
Old 04-05-19, 00:06
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Hi Guys. I am welding patches full length of the floor. The rear patch is cut from a piece of old floor (only about 60mm wide) that goes from the cam plate hole to the back. The rest is mild steel.
I found that the mig welds just cracked with a little bit of pressure from a cresent spanner, so i looked through my rod selection and found some "Hi-ten 7 rods. (Phillips rods)
Description in photo. I have tacked it and stitched it and welded both sides and sice the photo have welded the mild steel strip on one side. It seems to be going ok.
BTW, this floor (Canadian MkI U.C.)is approximately 3.9mm thick. this equates to about 0.153 inches which on the gauge scale is between 22g. and 23g.
10 gauge is 4.91mm- way heavier. Maybe later carriers had thicker floors? We've only ever had early ones here. Highest numbers in the 53xxx range.
First time my pictures haven't posted like I wanted them to.
Attached Thumbnails
20190504_094420_resized.jpg   20190503_153911_resized.jpg  
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....

Last edited by Lynn Eades; 04-05-19 at 00:53.
Reply With Quote
  #15  
Old 06-05-19, 04:24
Sam Tremblay Sam Tremblay is offline
Registered User
 
Join Date: Jan 2019
Location: Stanstead, QC, Canada
Posts: 14
Default

i will weld that any time with the mig the steel of mine look so soft so ready too weld wir=th any kind of welder
__________________
sam

1941 bren carrier mk1
1952 m38cdn 2x
1953 m37cdn
1976 bombardier alpine snowmobile
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tailgate welding. Jordan Baker The Softskin Forum 4 16-04-17 06:01
Carrier petrol tank floor cleats fixing ? RichardT10829 The Carrier Forum 3 21-02-12 00:59
all about welding Phil Waterman The Restoration Forum 16 30-04-11 00:57
WW2 welding trailers Ryan The Softskin Forum 4 26-05-10 06:17
Welding/machining help please Bruce Parker (RIP) The Restoration Forum 22 04-10-05 23:34


All times are GMT +2. The time now is 13:27.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016