MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Restoration Forum

Notices

Reply
 
Thread Tools Display Modes
  #61  
Old 17-07-17, 14:57
Phil Waterman's Avatar
Phil Waterman Phil Waterman is offline
Super Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,416
Default Alternative to rivets

Hi

While using rivits properly installed is the ideal approach, the alternative is bolts. The issue is that the bolt or rivit must be a tight fit in both layers of steel.

When I reassembled the frame of my Pat 12 C60L line bored each rivit hole location inplace through all layers to be attached. Each hole was sized so that it would be a drive fit on the shank of grade 8 bolt. Getting the bolts the right length so that the shank (unthreaded section) extended through the steel was the hard part. In the end I bought many different bolt lenghts. Then torque bolts to 75% of max for the bolt size.

The truck has been on the road for about 10 years with a lot of hard off road work hauling firewood with no signs of any of the joints loosening.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #62  
Old 18-07-17, 11:50
aj.lec's Avatar
aj.lec aj.lec is offline
Andrew
 
Join Date: Apr 2007
Location: N.S.W AUSTRALIA
Posts: 1,613
Default

Quote:
Originally Posted by sth65pac View Post

I removed the temporary brace and the 1/4" rivet misalignment has become about 1/16" ordered additional rivets but they are too small so I'll have to make up some with steel rod.

I bought a 'toy' oxy propane kit which is pretty useless. If it doesnt heat the rivets hot enough I will have to get a proper Oxy Acetelene kit for riveting.

Cheers,

Ian
The chassis do spring when you take the brace out . usually have to jack or tie them back in to location . Usually easier to bolt in and tighten first with tight fitting bolts and remove as you progress along

I use a LPG oxy kit but just use the cutting head instead of heating tips to get it hot enough . Not as quick as acetylene but don't have to pay dead rent on the acetylene bottle as well as oxy tank
__________________
Have a good one
Andrew

Custodian of the "Rare and Rusty"
Reply With Quote
  #63  
Old 18-07-17, 23:42
Jacques Reed Jacques Reed is offline
VMVC & Early Ford V8 Club
 
Join Date: Jul 2012
Location: Victoria Australia
Posts: 341
Default

Quote:
Originally Posted by aj.lec View Post
I use a LPG oxy kit but just use the cutting head instead of heating tips to get it hot enough . Not as quick as acetylene but don't have to pay dead rent on the acetylene bottle as well as oxy tank
Hi Andrew,

After decades of Cigweld/BOC holding oxy-acetylene users to ransom in Victoria with ever increasing rents you can now buy D size Oxy and Acetylene bottles through Bunnings. The company is called Coregas. Initial purchase is barely one years BOC rental charges. Refills for Acetylene is $99 and Oxygen is $69

As is so often the case I think it varies from state to state.

As an occasional user of oxy, these D bottles are ideal for me. I took great pleasure surrendering my D size BOC bottles last year and closing down the bottle lease after 20 years with them.

Cheers,
__________________
F15A GS 1944

Jacques Reed
Reply With Quote
  #64  
Old 19-07-17, 22:41
sth65pac's Avatar
sth65pac sth65pac is offline
Ian Williams
 
Join Date: Jul 2006
Location: Bomaderry NSW
Posts: 298
Default Drip Rails.

Quote:
Originally Posted by Bruce Parker View Post
How did you form those drip rails?
I measured all I had and got them folded up (two pieces per side) at the sheet metal shop near me. They taper in width on the lower (attached to old steel) I have the measurements if people are interested.

cheers,

Ian
__________________
Ian Williams

F15A,
2x Army Land Rover 88' sIIA's
GPW
Other stuff
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
starting handle cover Maurice Donckers The Carrier Forum 30 23-08-14 02:40
Crank Starting Harry Moon The Softskin Forum 6 23-07-13 22:16
Starting 1942 mb jeep Little Jo The Softskin Forum 6 16-06-11 02:10
Hot engine starting Barry Read The Carrier Forum 17 13-05-06 18:25
Jeep Starting Point Campbell Finlay The Softskin Forum 5 04-01-05 07:47


All times are GMT +2. The time now is 22:44.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016