![]() |
#1
|
||||
|
||||
![]()
Hi,
I need to change the oils in rear axle and gear box in my Austin K30, but I donīt know which. ![]() ![]() Can somebody help me? Many thanks Radek |
#2
|
|||
|
|||
![]()
Radek email Peter Scally...he will help you with this problem regards malcolm ps I thought I had sent you the Austin drivers manual for this vehicle!
__________________
mally B |
#3
|
||||
|
||||
![]()
Hi Radek,
Just gone down to my workshop at checked the manuals. In the wartime military K3 book, the gearbox and axle were filled with SAE 140 gear oil. That may be a bit heavy ( or thick ) for the temperatures in your country. Also looked at a 1947 civilian book for the Austin K4 and for Overseas use, in colder climates, the gearbox has SAE 90 gear oil and the rear axle has EP90 or Hypoid 90 gear oil. Hope this is of help to you.
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
#4
|
||||
|
||||
![]() Quote:
I will try Peter. Yes I have any mauals for this lorry, there are the lubrication charts, but old marking. Radek |
#5
|
|||
|
|||
![]()
Radek you can take the message from Richard as gospel (the truth) as Im sure he is an ex REME chap!(we all cant be in the Signals) cheers malcolm from a soon to be stormy North-Northumberland
__________________
mally B |
#6
|
||||
|
||||
![]() Quote:
![]() In my experience of several types of Austins, I would go for the Overseas / Cold Climate recomendations in the K4 manual , ie; gearbox > SAE90 and r/axle > EP90 or Hypoid 90 best regards
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
#7
|
|||
|
|||
![]()
Rcihard where you ever at Kinnegar N.I.(39Inf Bde) and do you know that other REME stalwart Doug Mathieson regards malcolm
__________________
mally B |
#8
|
||||
|
||||
![]() ![]() Quote:
Malcolm, Sending you a PM ![]()
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
#9
|
|||
|
|||
![]()
I would assume you also have to take into account if their are any metals in the axle which may be effected by a modern EP90.
I think most people say go for a GL3 spec or lower. |
#10
|
|||
|
|||
![]() Quote:
Good old 46 CMD, with its Det at Ballykelly. Didn't serve with the workshop, but had many dealings over the years 71-73 and 79-87. Not much left now in Ballykelly except the building, which I am led to believe is a listed building ![]() I still see some of the old civilian staff now and again around my area. Paul. |
#11
|
||||
|
||||
![]() Quote:
Fair comment re. the GL3, whether Radek would have the choice in his country, I do not know, but if there was any doubt, then a straight SAE 90 gear oil would be alright. Not that I can think of any bronze parts in the rear axle on an Austin.
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
#12
|
||||
|
||||
![]() Quote:
Hi Paul, Some confusion here ![]() ![]()
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
![]() |
|
|