MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Carrier Forum

Notices

Reply
 
Thread Tools Display Modes
  #91  
Old 20-08-15, 22:09
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Yes Petr, something like that, nickel looking and shiney.
It was rough with quite a bit of spatter etc, so I thought my quality of welding would be a good replica. The boss has a few old packets of stainless rods, so I used them.
We don't need to get back into the debate about what was used at the time.

At some point in time I am looking for the detail of the front (observers)shutter. I have nothing but the holes. There is one in France, in Nigel Watsons 3rd book. It is the best detail I have ever seen (Nigel did us such a great deed, putting those books together for us)
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....

Last edited by Lynn Eades; 20-08-15 at 22:15.
Reply With Quote
  #92  
Old 24-08-15, 14:07
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

As wise guys from the forum sad, I have also one potential issue regarding my nice and big aluminium oil pan. I have made some measurements and it really wont fit without some trimming.
1. the gearlever bar collide with the corner of oil pan, but these are only milimetres, Im sure that bar could be modifed to fit.
2. the current drain plug and bulge above it makes the height of oil pan too big - again its cca 5mm, so could be fixed by grinding whole bulge off and welding flat blanking piece of aluminium on it.
3. the drain plug must be repositioned to fit the hole in the floor.

So I think its still negotiable but with a great effort Im affraid. So if anyone from the honorable forum members has spare good steel oil pan for carrier for sale, I would be very grateful. Please let me know
Attached Thumbnails
oilpan1.jpg   oilpan2.jpg   oilpan3.jpg  
__________________
UCw Mk.III
Reply With Quote
  #93  
Old 24-08-15, 14:13
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Just for make it sure - this is the example of correct oil pan for carriers flatty, right?
11´ clutch, non removable flywheel cover
Attached Thumbnails
oilpanok.jpg   oilpanok1.jpg   oilpanok2.jpg  
__________________
UCw Mk.III
Reply With Quote
  #94  
Old 25-11-15, 11:54
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Not much to say, but heads are on again!
Also got nice Desmo mirror, still green paint underneath
Attached Thumbnails
headson1.jpg   headson.jpg   mirror1.jpg   mirror2.jpg  
__________________
UCw Mk.III
Reply With Quote
  #95  
Old 25-11-15, 14:07
eddy8men eddy8men is offline
AKA Rick Wedlock
 
Join Date: Dec 2009
Location: manchester
Posts: 715
Default

looks very nice
__________________
_______________________
1941 mk1 mortar Carrier
1941 Mk1* Carrier
1942 Mk1* Carrier
1943 T16 Carrier
1945 Mk3 Dingo
1941 Mk3 Covenanter
1941 Mk4 Churchill AVRE (now sold)
1944 Mk6 Cromwell (now sold)
1952 Mk3 Centurion
1952 ARV Centurion
1952 ARV Centurion
1953 Mk3 Centurion (breaking)
Reply With Quote
  #96  
Old 25-11-15, 22:16
RichardT10829's Avatar
RichardT10829 RichardT10829 is offline
Richard Harrison
 
Join Date: Nov 2008
Location: Cullercoats Newcastle Upon Tyne United Kingdom
Posts: 3,059
Default

Have you popped some thread locker or red hermitite on the head studs where they go into the block ?
__________________
is mos redintegro

__5th Div___46th Div__
1942 Ford Universal Carrier No.3 MkI*
Lower Hull No. 10131
War Department CT54508 (SOLD)
1944 Ford Universal Carrier MkII* (under restoration).
1944 Morris C8 radio body (under restoration).
Reply With Quote
  #97  
Old 25-11-15, 22:58
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Yes Richard, they were sealed wit Loctite. I also put a thin layer of copper sealant on the head gasket. Should be OK.
__________________
UCw Mk.III
Reply With Quote
  #98  
Old 30-11-15, 11:23
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

New sparks ready for the Advent time
Attached Thumbnails
sparks.jpg  
__________________
UCw Mk.III
Reply With Quote
  #99  
Old 30-11-15, 19:51
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Petr, which ones are they? (model number)
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #100  
Old 30-11-15, 20:37
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Lynn, B6L's.
__________________
UCw Mk.III
Reply With Quote
  #101  
Old 20-12-15, 21:39
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Just made some quick set up of the front of the engine. You can see brand new single pulley pumps there - Im still thinking about use of only one belt as an option (maybe just temporarily).
Dont have proper double crankshaft pulley yet and I think that modern belts are much more capable to the original ones, so even one single belt can withstand the torque of the two old ones. Bad idea?
Anyway, I have double pulleys for pumps on stock, so can be replaced if needed. Still looking for the crankshaft pulley though.
Attached Thumbnails
engf1.jpg   engf2.jpg  
__________________
UCw Mk.III
Reply With Quote
  #102  
Old 20-12-15, 21:54
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Petr,Do you have the original fan?
It takes a lot of driving and I think both belts will be required.
The fan mounts on a fan extension which has a fibre coupling to drive the generator. No side load is put on the generator bearings.
Usually double pulley water pumps have a bearing in them. Single pulley pumps are bushed.
Your generator is not the right one. It should have a thread on the drive end to take a keyed drive dog.
If you need photos I can look for them.

Edit. The fan needs to be positioned in the fan shroud to work properly. The fan extension does this. you should aim to fit all the shrouds to help the difficult task of moving cool air through the radiator etc.
I have seen carriers that overheat because parts are left out.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #103  
Old 20-12-15, 22:03
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

No Lynn, Im missing fan extension too, so Im a bit improvising there.
So far I have smaller fan on hand, which is mounted directly to the generator pulley.
__________________
UCw Mk.III
Reply With Quote
  #104  
Old 21-12-15, 07:54
Marc van Aalderen's Avatar
Marc van Aalderen Marc van Aalderen is offline
Registered User
 
Join Date: May 2009
Location: Veenendaal, The Netherlands
Posts: 481
Default

DON'T DO THAT!!!

Last year my carrier, with a similar set-up, had the generator shaft break with the fan destroying the radiator! The generator shaft is not strong enough to hold both the fan and the force of the V belts.

I have photos of the incident but do not no how to reduce size so I can post them...

Cheers,
__________________
Marc van Aalderen

Daimler Dingo Mk1B 1941
Daimler Armoured Car Mk1 1943
Daimler Ferret Mk1/1 1959
Ford Universal Carrier No2 MkII* 1944
Ford GPW British Airborne 1944
Lightweight 10 Cwt Trailer SS Cars Ltd 1944
Anti-Tank Gun 6 Pdr 7 Cwt MkII 1942
Daf Trailer YAA602 1954
Daf Trailer AT16-24-1NL 1977
Daf 2100Turbo 1982
Reply With Quote
  #105  
Old 21-12-15, 08:06
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Marc, from what I have been told, even the proper set up fails. The fan centre is a known weakness. However I have heard of more "jackup" failures.
My advice (unqualified) Petr, is look for the right bits.
You have a lot of original bits, with potential for a very original carrier.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #106  
Old 21-12-15, 09:04
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Marc, I heard about this incident at Market Garden, but didt saw it on my own eyes. Pics would be certainly useful for me, will send you my email in PM. Thank you!
So guys, thanks both for an advices, surely will try to source all proper bits and set-up the engine as it should be. But it takes time.
Untill I get them, safe and working (but very ugly, I know) solution would be possibly electrical fan.
__________________
UCw Mk.III
Reply With Quote
  #107  
Old 21-12-15, 09:58
eddy8men eddy8men is offline
AKA Rick Wedlock
 
Join Date: Dec 2009
Location: manchester
Posts: 715
Default

I used an electric fan on my carrier until I could get hold of the correct setup, it wasn't pretty but it got the job done
__________________
_______________________
1941 mk1 mortar Carrier
1941 Mk1* Carrier
1942 Mk1* Carrier
1943 T16 Carrier
1945 Mk3 Dingo
1941 Mk3 Covenanter
1941 Mk4 Churchill AVRE (now sold)
1944 Mk6 Cromwell (now sold)
1952 Mk3 Centurion
1952 ARV Centurion
1952 ARV Centurion
1953 Mk3 Centurion (breaking)
Reply With Quote
  #108  
Old 21-12-15, 10:33
RichardT10829's Avatar
RichardT10829 RichardT10829 is offline
Richard Harrison
 
Join Date: Nov 2008
Location: Cullercoats Newcastle Upon Tyne United Kingdom
Posts: 3,059
Default

I am at a similar crossroads... I have all the correct bits at present but want to run high volume water pumps...... All of which are single pulley, I can't fit my twin pulleys to the new pumps so was going to run one V belt rather than two.... Not sure I will now.
__________________
is mos redintegro

__5th Div___46th Div__
1942 Ford Universal Carrier No.3 MkI*
Lower Hull No. 10131
War Department CT54508 (SOLD)
1944 Ford Universal Carrier MkII* (under restoration).
1944 Morris C8 radio body (under restoration).
Reply With Quote
  #109  
Old 21-12-15, 10:51
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Richard, why do you want to run high vol. pumps?
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #110  
Old 21-12-15, 11:46
RichardT10829's Avatar
RichardT10829 RichardT10829 is offline
Richard Harrison
 
Join Date: Nov 2008
Location: Cullercoats Newcastle Upon Tyne United Kingdom
Posts: 3,059
Default

Pumps that are on are absolute dog muck.

If I am going to spend the wedge I would rather pay for something that works well.
__________________
is mos redintegro

__5th Div___46th Div__
1942 Ford Universal Carrier No.3 MkI*
Lower Hull No. 10131
War Department CT54508 (SOLD)
1944 Ford Universal Carrier MkII* (under restoration).
1944 Morris C8 radio body (under restoration).
Reply With Quote
  #111  
Old 29-12-15, 16:02
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Finally got one very important part! Coupling gear
Attached Thumbnails
torzo002.jpg  
__________________
UCw Mk.III
Reply With Quote
  #112  
Old 29-12-15, 21:45
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

After Christmas cross-fit. Dismantling of the heavily converted carrier chassis I got. Poor guy tried to build a tracked wineyard cultivator on the carrier basis. He did destroy british made, late production vehicle, very rare. Still some nice useabl parts though.
Attached Thumbnails
torzo001.jpg   torzo003.jpg   torzo005.jpg   torzo006.jpg   torzo004.jpg  

__________________
UCw Mk.III
Reply With Quote
  #113  
Old 29-12-15, 21:47
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

More pictures
Attached Thumbnails
torzo007.jpg   torzo008.jpg   torzo009.jpg  
__________________
UCw Mk.III
Reply With Quote
  #114  
Old 22-02-16, 10:37
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Slowly progressing, few parts refurbished (mainly steering and linkages). I had to totally rebuild also clutch plate, even it was "professionaly rebuilded" by some US company quite time ago and never used since. One lever had a massive dead play, because bushings were just weared out crap. No needle rollers there, just bronze bushings, which is quite common on rebuilded clutches I think.
Engine is almost ready, but need new starter motor armature - unfortunately mine has short circuit to the shaft :-(
Attached Thumbnails
IMG_7867.jpg   IMG_7869.jpg   IMG_7870.jpg   IMG_7879.jpg   IMG_7885.jpg  

__________________
UCw Mk.III
Reply With Quote
  #115  
Old 10-03-16, 11:39
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Finally got the set of "rifle rests" over the top of the armour. It's a sort of "simple shape" but difficult-to-make parts. Very happy with the result
Attached Thumbnails
rest1.jpg   rest2.jpg  
__________________
UCw Mk.III
Reply With Quote
  #116  
Old 10-03-16, 14:04
Michael R. Michael R. is offline
Registered User
 
Join Date: Jun 2011
Location: Canada
Posts: 1,154
Default

They look excellent!
Reply With Quote
  #117  
Old 10-03-16, 14:22
Radek's Avatar
Radek Radek is offline
Registered User
 
Join Date: Sep 2007
Location: Czech Rep.
Posts: 379
Default rifle rests

nice! I will need any to. ;-)
__________________
____________________________
Austin K30 1940
Austin AP8 1940
Austin 10hp G/YG "Tilly"
Royal Enfield WD/CO 1942
British airborne trailer

family
Austin K2/Y Ambulance 1939
Austin K30 1940
Austin Champ 1954
...
Reply With Quote
  #118  
Old 10-03-16, 19:12
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Petr, on your pressure plate (in a photo in previous post) you have "29.6"
Is that the finger height? if so, was it set on a particular spacer thickness?

How did you roll the rests? What sort of machine?
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #119  
Old 11-03-16, 09:48
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

Hi Lynn, "29.6" is just my reference value from some accessible surface of the clutch disc, in fact, it doesn't mean nothing specific to the flatheads. I set all three fingers to this height, should be OK, but haven't tested it yet.

Believe me or not, none special tooling or machines been used for making the rests. Only very skillful craftsman and good idea
If needed, I think some more could be done
__________________
UCw Mk.III
Reply With Quote
  #120  
Old 17-03-16, 23:41
Petr Brezina Petr Brezina is offline
Registered User
 
Join Date: Mar 2014
Location: Czech Republic
Posts: 533
Default

I did compression check today and Im happy with the result. 95 to 110 psi on all cylinders, oil pressure on cranking speed 35 psi - its going to be a beast
Hopefully will try to fire it soon - looking forward to it
Attached Thumbnails
compression2.jpg   compression1.jpg  
__________________
UCw Mk.III
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New Project ron The Carrier Forum 3 17-07-17 22:00
A new project Tim Lovelock The Softskin Forum 15 17-07-12 13:58
FGT project Tony Wheeler The Restoration Forum 38 12-07-12 06:09
Project F15 Howard The Softskin Forum 162 07-02-09 07:47
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project Alain For Sale Or Wanted 1 21-02-07 00:11


All times are GMT +2. The time now is 16:27.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016