#91
|
||||
|
||||
For a C15a single speed Transfer Case
Transfer Case Modern oil seal part number is SKF 19360 QTY3 Speedi Sleeve is SKF 99193 QTY 3 Shift shaft CR 5510 (or SKF) per Tony Smith Bearings as listed in the parts manual. Timken 332. QTY 6 Timken 339. QTY 5 Timken 342-S. QTY 1 Timken 14274 QTY 2 Timken 14137 QTY 2
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer Last edited by Jordan Baker; 20-02-19 at 09:24. |
#92
|
|||
|
|||
2 speed transfer case seal
Does anybody have the part# for the small seal that fits on the shift shaft of the 2 speed transfer case. the one that goes on the shaft that attaches to the shift fork? I looked through this thread and I couldn't find a reference to it.
Last edited by Harry Moon; 05-10-18 at 23:40. |
#93
|
|||
|
|||
try the dimension for a search...
Hi Harry
Was at a seal wholesaler today and they still prefer to search by OD/ID since numbers vary from manufacturer and over time..... once found they give you a choice of made by 'who' where (time) and/ or shipping cost. You can probably figure out the ID easy enough but it will be a hell of a tight fit to measure the OD without taking your T case out.... Any body on the forum that has a 2 speed already taken apart for measuring.... I would suspect that the size for the two rods on the 2 speed and the one speed T case are the same...... need some time to read and compare in the parts manual.......... Mine where tight when I rebuilt my t case...... one of the few parts I did not have to change. Good luck
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#94
|
|||
|
|||
|
#95
|
||||
|
||||
Seal part number lookup
Harry, if you can measure the shaft diameter and bore, go to http://www2.chicago-rawhide.com/ and click on "Seals North America Part Lookup".
Entering the ID and OD will give you a match from the current SKF seal catalogue, which in turn can be crossmatched to other manufacturers. HTH, Hanno
__________________
Regards, Hanno -------------------------- |
#96
|
|||
|
|||
oil/grease seals ........
Front brake drum.....C8, HUP C15A possibly others.....
SKF brand new..... part number 45150...... easy stock item at baring suppliers Price as of Oct 2018 IN OTTAWA...... $136.39 INCLUDING TAX Bob C
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#97
|
|||
|
|||
I put 2 in and it seems good.
|
#98
|
|||
|
|||
Front Brake Hoses for 6 inch front brakes
In building up the big 6 inch front axle with the big brakes I found the BH5931 hoses to short to cover the range of movement. I sourced BH6222 and they are the same length as the originals and have the same 5/8 thread end as well. I would recomend these be added to the parts list for 6 inch axles and they would be fine on a 5 inch axle as well..
Last edited by Harry Moon; 23-01-19 at 04:22. |
#99
|
||||
|
||||
In the 5” or 6” axle. What is being measured to determine those sizes? Was one used on the 15cwt trucks?
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#100
|
|||
|
|||
The flange....... near the egg cup....
You can tell the 5 from the 6 from the flange cross section diameter....6 also has more bolts on the flange an the six has 6 bolts holding the top cap where the new departure bearing is located.......small C15a larger on C60 but there are exceptions Aussie C60 made in Canada late in the war has small axles and 16 in tires.
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#101
|
||||
|
||||
Thanks. I see the differences now. And with 7min to spare I learned something new today.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#102
|
|||
|
|||
spotting a 6 inch front axle
the easiest way to spot the 6 inch front axle with the larger brakes from the regular 5 inch front axle is at the hub. you can see the obvious bulge behind the lift ring on the 6 inch. not so obvious is that the wheel base is wider by a couple of inch's.
Soi far I have only seen the bigger 6 inch on FAT's and winch trucks. |
#103
|
|||
|
|||
Chevrolet master cylinders
Somewhere in the past there had to have been a Wagner/Raybestos/Delco part number for the original master cylinder. Anybody have that information? Might be useful in checking out old NOS stock we sometimes come across.
|
#104
|
||||
|
||||
Seal sizes for transfer case
So I just pulled the seals out of my transfer case and they all appear to be the same size. One was so bad that the oil could have been drained out the gap instead of the drain hole.....
Two of them have a paper gasket behind the plate and they are in bad shape. The input one has a steel gasket in place and no paper ones. Any ideas on sourcing these paper gaskets? The steel one looks fine although I am unsure if it would work without a paper one as well? If it was aluminum or copper I could see it being a crush type but it is definitely steel (has rust). Thoughts on the gaskets? Should I just try to cut my own?
__________________
Many projects..... Complete- Ford F8 truck Complete-1956 Mk 2/3 Ferret Complete- Bofors 40mm on carriage Complete Reproduction- Vickers, Model 1937 Tank Waiting restoration- 1950 Cambridge carrier, Ford CMP Water truck, 1943 Universal carrier, 1945 Dodge APT truck, Canadian C3 Howitzer, several parts vehicles and a few ideas..... |
#105
|
||||
|
||||
I believe the steel one to be a shim. In the MB-C2 manual there is a very good detailed write up on the servicing and rebuilding of the transfer cases.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#106
|
||||
|
||||
Does anyone have a source for the through bolts used on these brass blocks and for the rear brake one? All of mine were rusted junk. Are the front ones the same as the rear ones?
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#107
|
|||
|
|||
Check these
|
#108
|
|||
|
|||
NAPA has them complete with or without washers. You just need to know your thread size (usually 7/16-20 on most of the old North American stuff). Use the term "Banjo" bolt when talking to the (oldest) parts guy. I find the younger parts guys go crosseyed when you use common terms like this.
If you lived closer, I have a bin of about 50 of them out in the shed. |
#109
|
||||
|
||||
Ok great. I just wasn’t sure as there seemed to be different ones. I’ve got an old school NAPA in town. I’ll go visit them tomorrow.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#110
|
||||
|
||||
Not truly a modern part but these are measurements from NOS felt seals used in the steering knuckles.
These are for the 6” ones but are the same for the 5” axles except in overall length. The length is 24-1/2”
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#111
|
|||
|
|||
Felt Steering Ball Seals
Hi Jordan
Thanks, good information to add to CMP Knowledge Base. I've been using leather replacements since 1979 back then it was really hard to get information on CMPs. My first discussions with anybody who could answer questions was via regular mail. The first responses I got were from guys in Australia and New Zealand. Cheers Phil
__________________
Phil Waterman `41 C60L Pattern 12 `42 C60S Radio Pattern 13 `45 HUP http://canadianmilitarypattern.com/ New e-mail Philip@canadianmilitarypattern.com |
#112
|
|||
|
|||
Transmission seal- Ford CMP
Good Day,
Here's another seal number that fits the Ford transmission rear seal to add to CR 21211 KOK brand Part No. TC 12167, rubber covered. They conveniently even give the dimensions embossed on the seal, in inches no less! KOK is a Taiwanese company so probably available worldwide. Cost $10 at the local bearing shop in Australia. Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed |
#113
|
||||
|
||||
Ian found out the hard way (= buying the wrong seal), that the Ford F15A seal front hub inner 5", Ford part number C01Q-1190B matches with SKF/ CR 49998 with ID 5" and OD 6.25"
http://www.mapleleafup.net/forums/sh...638#post264638
__________________
Regards, Hanno -------------------------- |
#114
|
|||
|
|||
Buying the wrong parts
Hi Hanno,
It is easy enough to do, get the wrong part, I have a box or two of them, but measurements in the case of seals are the only true way to go. Even then, take the sample and, if possible, the part it is intended to fit to the shop. I did that with the rear transmission mount and seal and the bearing dealer confirmed my measurements. Of course, in these days of mail order only without bricks and mortar shops it is often hard to compare parts. I downloaded the CR Seals Handbook (SKF) and it is a wealth of information besides listing available sizes of seals and Speedi Sleeves. Recommended download for any restorer of any vehicle. Cheers,
__________________
F15-A 1942 Battery Staff Jacques Reed |
#115
|
||||
|
||||
Quote:
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should! |
#116
|
||||
|
||||
Quote:
Going back through the releated threads the correct info was there indeed, but I did not help with muddling it up. The p/n I shared is correct for the seal with the dimensions shown, but that seal does not cross reference to C01Q-1190B. It now turns out I was wrongly informed and have been sold the wrong seal as as well... Anyway, I have offered compensation and invited Ian to add his lessons-learned to this thread.
__________________
Regards, Hanno -------------------------- |
#117
|
||||
|
||||
Rebuild Kit for Ford master brake cylinder
Ford master brake cylinder, 1 1/4" bore: current part number of a Rebuild Kit is 91T-2004-A, 91T-2004.
These kits seem to be quite easy to source in the USA, Canada and the UK, but I could not find a rebuild kit closer to home - until I remembered this: Quote:
https://staman.nl/product/kit-repair...ylinder-dodge/
__________________
Regards, Hanno -------------------------- |
#118
|
||||
|
||||
Applicable to the Otter, C15TA and I believe the Fox AC and C60X transmission.
4.319 2075286 Seal, Mainshaft Rear Bearing Cap Oil Modern SKF / CR 17645
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#119
|
|||
|
|||
I had to do a rear U-joint on an artillery tractor (Chev) a couple days ago and found the U joint that was commonly referred to on MLU was too short. The U joint referred to equals a UJ331 (the 331 is a common reference and the spicer number is 5-1350x). Caps are 1.188 diameter and the height is 3.622
A little research led to the right U-joint. The caps are 1.188 diameter and the height from top to bottom on the caps is 4.187. They are spicer 1410 series U joints and use part number 5-1410X. Another common trade number is UJ330. It may be that the number listed on MLU is for the smaller or earlier trucks. But the various cab13 shafts I have sitting here all appear to use the latter UJ330 (spicer 5-1410X) U-joint. |
#120
|
||||
|
||||
Rob, these are the parts I had a heavy truck shop tell me where the same as what I brought in from my C15a truck.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
Thread Tools | |
Display Modes | |
|
|