MLU FORUM  

Go Back   MLU FORUM > GENERAL WW2 TOPICS > The Wireless Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 24-11-13, 11:02
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default variometer mounting

Hi, Does any one know what mounting bracket I need to mount a variometer to the inside of a universal carrier on the Mk1 set up?, also what length of lead will I require to go from it to the rear aerial?.

further questions to come I am sure, also looking for a 4B 'Dog Bone'.

thanks kevin.
Attached Thumbnails
radio11.jpg  
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #2  
Old 24-11-13, 15:10
Jon Skagfeld's Avatar
Jon Skagfeld Jon Skagfeld is offline
M38A1 CDN3
 
Join Date: Feb 2003
Location: Owen Sound ON
Posts: 2,190
Default

Bruce Parker or Stewart Loy should chime in, if they're on-line.
__________________
PRONTO SENDS
Reply With Quote
  #3  
Old 25-11-13, 14:22
Bruce MacMillan Bruce MacMillan is offline
a Canuck/Brit in Blighty
 
Join Date: Jul 2004
Location: Hell Fire Corner, Kent UK
Posts: 697
Default

According to EMER FZ256/3 the variometer uses 2 pieces.

Pieces, packing No. 1 ZA2993
Plate, metal, seating, aerial Variometer ZA/CAN1075

The ZA2993 is used on other vehicles so should be common.

aerial feeder assy No. 7 ZA10220 uses a 16" lead
connector, single, 16" ZA/CAN1351
Reply With Quote
  #4  
Old 25-11-13, 17:26
Ron Pier's Avatar
Ron Pier Ron Pier is offline
Registered User
 
Join Date: Apr 2009
Location: Poole. UK
Posts: 1,253
Default

This is on Ebay at the moment quite cheap.
http://www.ebay.co.uk/itm/Pye-Link-P...item43c25b73e8
I have a coil of WS19 co axe cable.

Ron
Reply With Quote
  #5  
Old 01-12-13, 15:06
Johnny Canuck Johnny Canuck is offline
Geoff Truscott
 
Join Date: Aug 2011
Location: Ottawa, Ontario, Canada
Posts: 158
Default

It would appear that a special mounting bracket is required for a Universal Carrier installation.
The Packing Piece No.1 (wood, rubber, bakelite) and a Seating Plate Metal are required. These are fastened to the Variometer with 3 screws ( the 3 holes are visible on the underside of the Variometer case)
The problem is how to fasten this assembly to the vehicle as you can not reach the mounting screws once the Variometer is attached to the plate assembly.
A Brackets, Metal, Mounting, Variometer No.C1 (ZA/Can 1376) is required to mount it to the Vehicle.
This bracket is just visible as the hashed line behind the Variometer in the picture you posted.

Geoff

You need items 2, 27 and 28




Last edited by Johnny Canuck; 01-12-13 at 15:23.
Reply With Quote
  #6  
Old 01-12-13, 17:03
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Hi johnny, that info is great!, I have seen the spacer available but I guess the metal bracket would be difficult to get, has anyone got a drawing of it, looks easy to make.

Regards Kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #7  
Old 01-12-13, 22:00
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Kevin, my carrier has that mounting for the variometer. However I am a few thousand miles away from home for a while. Check my carrot thread and there might be some pictures of it.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #8  
Old 14-12-13, 00:17
Chris Suslowicz Chris Suslowicz is offline
Junior Password Gnome
 
Join Date: May 2007
Location: England
Posts: 814
Default

Quote:
Originally Posted by kevin powles View Post
Hi johnny, that info is great!, I have seen the spacer available but I guess the metal bracket would be difficult to get, has anyone got a drawing of it, looks easy to make.

Regards Kevin.
As Johnny (Geoff?) said, you need items 2, 27 and 28 (plus Aerial Feeder No.7).

Item 2 is the bracket that bolts to the carrier hull and supports everything.
Item 27 is the "Piece, Packing" and is just a spacer between the curve of the variometer and the flat mounting surface of the bracket.
Item 28 is the critical part: "Plate, Seating" - it's a stretched hexagon matching the outline of item 27 and has a row of pressed-in countersunk holes for the three variometer fixing screws, plus two spot-welded metal strips (it's too thin, otherwise) with a pair of tapped holes in each to fit it to the bracket (Item 2).

I suspect the assembly sequence is:

First, fit the aerial feeder cable to the plate and fit that to the variometer.
Next, assemble items 27 and 28 and fix them to the "barrel" of the variometer with 3 screws provided.
Then fix the whole assembly to item 2 with the four screws provided.
Finally, fit item 2 to the vehicle hull.

(Trying to do it any other way, e.g: fitting the hull bracket first, will be very difficult because you won't get a screwdriver under the bracket even if you have eyes in your fingertips.)

Once that's all done you can feed the aerial cable through the aerial mounting (don't forget the rubber sleeve), attach the connector plate to the cable and position it on the top of the mounting (rubber gaskets as desired), then screw the pigtail lead into the underside of the aerial base, connect the pigtail to the connector plate (centre contact - ring terminal and very fiddly screw), then fix the whole lot to the aerial mounting plate with the six bolts.

After all that, a cup of tea (or something stronger) is definitely recommended.

Chris.
Reply With Quote
  #9  
Old 14-12-13, 10:16
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Thanks Guys, A kind gentlemen on this forum has already done me a very nice drawing of item 2, the fixing bracket. Many thanks for the other info.

Does anyone have item 28 the steel bracket they could loan me to copy?, I understand item 27 the wood packing piece is quite common so should be available to purchase at some point in time.

regards kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #10  
Old 23-12-13, 12:39
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default Shared information.

Hi, A kind gentleman has supplied this information to me, will start making in the new year.


Many thanks Kevin.
Attached Thumbnails
image.jpg  
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #11  
Old 04-01-14, 01:24
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Quote:
Originally Posted by Johnny Canuck View Post
It would appear that a special mounting bracket is required for a Universal Carrier installation.
The Packing Piece No.1 (wood, rubber, bakelite) and a Seating Plate Metal are required. These are fastened to the Variometer with 3 screws ( the 3 holes are visible on the underside of the Variometer case)
The problem is how to fasten this assembly to the vehicle as you can not reach the mounting screws once the Variometer is attached to the plate assembly.
A Brackets, Metal, Mounting, Variometer No.C1 (ZA/Can 1376) is required to mount it to the Vehicle.
This bracket is just visible as the hashed line behind the Variometer in the picture you posted.

Geoff

You need items 2, 27 and 28



Hi, Does anyone know where I can get the top two straps (item 10) of the featured drawing, also the 6 pin dog bone.

thanks kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #12  
Old 04-01-14, 02:04
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

I had to buy an extra one of the linfer straps and cut it down. Was simple to pop off the rivets and shorten it.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #13  
Old 05-01-14, 02:26
Chris Suslowicz Chris Suslowicz is offline
Junior Password Gnome
 
Join Date: May 2007
Location: England
Posts: 814
Default

Quote:
Originally Posted by kevin powles View Post
Hi, Does anyone know where I can get the top two straps (item 10) of the featured drawing, also the 6 pin dog bone.

thanks kevin.
Item 10 is declared as "Carriers, Set, No.22", which may just be the metal frame. The set retaining strap is the same length as the longer strap in the No.21 or No.23 carriers, but the one for the supply unit is somewhat longer than the supply unit mounting strap for those carriers (as the supply unit fits on top of the set - using the same steel angle strips as used on Carrier 21 or 23 (screwed into the flat plates on the set top)). You may need to cut a longer strap down to make the supply unit mounting strap.

The strap lengths are listed in the Parts Identification section of the EMER, but I'm not sure what the length actually represents! (Just the canvas bit, from the studs to the strap-end of the thread, or the overall length of the whole thing.)

Chris.
(Carriers 1, 2 & 3 were renumbered 21,22 & 23 at some point, 24 is for the WS22 (I think) and 25 is an all-steel carrier for a demountable WS19 used in vehicles (similar to the No.3/23 wooden board type but shorter and with a single very long strap that goes around set and supply unit, plus a plate on top of the set to carry the variometer, an aerial base and a control unit. I'm still looking for the supply unit adapter plate for this carrier.)
Reply With Quote
  #14  
Old 05-01-14, 11:50
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Hi , Many thanks for the info, it appears all very complicated and the line drawings shown are not that clear, what I really need is a few pictures of what a correct bren gun carrier radio mount, strap and brackets assembly looks like in situ, I will post a picture of the radio trays I have currently, they both came out of carriers and look correct.

Regards Kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #15  
Old 05-01-14, 18:37
Bruce Parker (RIP) Bruce Parker (RIP) is offline
GM Fox I
 
Join Date: Feb 2003
Location: SW Ontario, Canada
Posts: 2,606
Default 19 Set pics

Here's some shots of the various bits. The first shows the factory supplied 11 set base bolted to the running board. The 19 set adapter plate is leaning loose above it. You have to remove the 11 set rails and install the 19 set ones using the same (outer) set of holes.

Then there are four rubber 'feet' that bolt onto the adapter plate and then to the underside of the 'Carrier No.22' which is what the 19 set sender/receiver is fastened to with the canvas strap. There is a secondary sheet metal plate with a junction box that also fits the same holes at the right (or vehicle rear) side of the set. The supply unit sits sideways on top of the sender/receiver held in place by two metal angles that are screws to the top of the set, two 'pieces packing' and a canvas strap.
Attached Thumbnails
DSC00823.jpg   DSC00825.jpg   DSC00827.jpg   DSC00828.jpg  
Reply With Quote
  #16  
Old 05-01-14, 18:39
Bruce Parker (RIP) Bruce Parker (RIP) is offline
GM Fox I
 
Join Date: Feb 2003
Location: SW Ontario, Canada
Posts: 2,606
Default Variometer and Control Unit

More pics.
Attached Thumbnails
DSC00829.JPG   DSC00826.jpg  
Reply With Quote
  #17  
Old 05-01-14, 18:51
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default Many thanks.

Hi Bruce, I see you are still me hero!. Many thanks for help past and present, what I do need is a drawing of that metal plate the control unit bolts too, I made the vario bracket last week, will studying your pics in detail on my laptop later.

Thanks again Kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #18  
Old 05-01-14, 18:53
universalgrl universalgrl is offline
Roberta
 
Join Date: Apr 2010
Location: Comox BC
Posts: 157
Default CU and variometer mounts

Any possibility of posting line drawings of the CU and variometer mount?
__________________
Roberta Jayne Melville CD II QJ

MK I * universal carrier
1942 WLC Harley under restoration
1957 M38A1 jeep
R.E.L. optical equipment
Military manuals
Field phones
MK II 19 set (needs work)
4 MK III W-19 sets
AN/PRC-9
CPRC-26
WS-29 componets
WS-38 AFV
WS-38 MK III
WS-48 with generator
WS-58 MK I
MK V heliograph
Reply With Quote
  #19  
Old 05-01-14, 19:07
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Quote:
Originally Posted by universalgrl View Post
Any possibility of posting line drawings of the CU and variometer mount?
Hi, I would post the varo mount drawing but it's a PDF file and I can't work out how to post it GGrr#*+

Give me 48 hours.

Kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #20  
Old 05-01-14, 20:11
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default Attaching PDFs

You can post PDFs using the same "Manage Attachments" screen as for JPG or other formats. The size limit is 244.1 KB.
Reply With Quote
  #21  
Old 05-01-14, 20:29
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Quote:
Originally Posted by Grant Bowker View Post
You can post PDFs using the same "Manage Attachments" screen as for JPG or other formats. The size limit is 244.1 KB.
Grant, The file is to big, if I email you the file, can you reformat it or something to post it?.

kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #22  
Old 05-01-14, 21:16
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

I can certainly try, both the PM and e-mail links on my profile should work.
Reply With Quote
  #23  
Old 06-01-14, 12:02
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

The attached PDF looked readable on my computer, if it won't open please let me know and I'll try again.
Attached Files
File Type: pdf Ws19 variometor brk.pdf (86.9 KB, 59 views)
Reply With Quote
  #24  
Old 06-01-14, 22:22
Chris Suslowicz Chris Suslowicz is offline
Junior Password Gnome
 
Join Date: May 2007
Location: England
Posts: 814
Default

OK, back on the Set Carrier components list, you will need:

Stores Code Qty Description

ZA.10430 2 Brackets, Angle, No.9
ZA.3103 1 Carriers, Set, No.22
ZA.14972 1 Bases, Carrier No.2
ZA.14030 4 Shock Absorbers, Bridge, No.2 Mk.II
ZA.2987 1 Straps, Clamping, No.1
ZA.2949 1 Straps, Clamping, No.3 (also known as Strap Assembly 14.3/4-in No.1)
ZA/CAN 0655 4 Pads, shock mounting, No.C1
ZB/CAN 2855 12 Screws, BA, Steel, No.2 x 3/8-in

The angle brackets are plated steel, identical to the removable ones on the other carriers, with 6 holes in each. These are fixed to the plates on top of the set case using the 2BA cheesehead screws. (The Strap, Clamping, No.3 is laid on the set case _first_ and the brackets fitted over the top of it, as it won't go underneath afterwards.) After thatn the Pads, Shock Mounting are put on top of the brackets (they are either thick pieces of canvas or sponge rubber to protect the case from the screwheads), the supply unit case laid on its side on top and fastened down using the Straps, Clamping, No.3. Job done!

You are going to have difficulty sourcing Straps, Clamping, at the best of times (and the No.3 in particular) as most WS19 owners took them off and lost them - the set is too damned heavy to move around on its carrier unless you have two people, and removing the set and supply unit, moving the carrier, then reinserting the set and supply unit into their cases is fiddly and time consuming. The No.3 is custom to the Sexton SPG and Universal Carrier, so rather more scarce than the usual (No.2) supply unit strap.

Original shock absorbers will almost certainly have disintegrated by now, but there's a modern equivalent vibration mounting that can be cut to the right size (and bent to shape if you're a perfectionist).

I'll see if I can work out what the 14.3/4-in dimension refers to so you know if you've got the correct strap. Other parts are common to the standard set carriers s I can provide photographs and measurements if required.

Chris.
Reply With Quote
  #25  
Old 07-01-14, 00:06
kevin powles's Avatar
kevin powles kevin powles is offline
Registered User
 
Join Date: May 2006
Location: united kingdom
Posts: 1,955
Default

Quote:
Originally Posted by Chris Suslowicz View Post
OK, back on the Set Carrier components list, you will need:

Stores Code Qty Description

ZA.10430 2 Brackets, Angle, No.9
ZA.3103 1 Carriers, Set, No.22
ZA.14972 1 Bases, Carrier No.2
ZA.14030 4 Shock Absorbers, Bridge, No.2 Mk.II
ZA.2987 1 Straps, Clamping, No.1
ZA.2949 1 Straps, Clamping, No.3 (also known as Strap Assembly 14.3/4-in No.1)
ZA/CAN 0655 4 Pads, shock mounting, No.C1
ZB/CAN 2855 12 Screws, BA, Steel, No.2 x 3/8-in

The angle brackets are plated steel, identical to the removable ones on the other carriers, with 6 holes in each. These are fixed to the plates on top of the set case using the 2BA cheesehead screws. (The Strap, Clamping, No.3 is laid on the set case _first_ and the brackets fitted over the top of it, as it won't go underneath afterwards.) After thatn the Pads, Shock Mounting are put on top of the brackets (they are either thick pieces of canvas or sponge rubber to protect the case from the screwheads), the supply unit case laid on its side on top and fastened down using the Straps, Clamping, No.3. Job done!

You are going to have difficulty sourcing Straps, Clamping, at the best of times (and the No.3 in particular) as most WS19 owners took them off and lost them - the set is too damned heavy to move around on its carrier unless you have two people, and removing the set and supply unit, moving the carrier, then reinserting the set and supply unit into their cases is fiddly and time consuming. The No.3 is custom to the Sexton SPG and Universal Carrier, so rather more scarce than the usual (No.2) supply unit strap.

Original shock absorbers will almost certainly have disintegrated by now, but there's a modern equivalent vibration mounting that can be cut to the right size (and bent to shape if you're a perfectionist).

I'll see if I can work out what the 14.3/4-in dimension refers to so you know if you've got the correct strap. Other parts are common to the standard set carriers s I can provide photographs and measurements if required.

Chris.
Hi Chris, Any pictures you may have will certainly help in this installation, It's seems a shame I cant use my original radio carrier in the bren carrier for the No11 set, Now I have to source the correct one for the 19 set.

kevin.
__________________
2pdr Tank Hunter Universal Carrier 1942 registered 11/11/2008.
3" Mortar Universal Carrier 1943 registered 06/06/2009.
1941 Standard Mk1 stowage Carrier, Caunter camo.
1941 Standard Mk1 stowage Carrier, light stone.
10 cwt wartime mortar trailer.
1943 Mk2 Daimler Dingo.
1943 Willys MB.
1936 Vickers MG carrier No1 Mk1 CMM 985.
Reply With Quote
  #26  
Old 09-01-14, 00:40
Chris Suslowicz Chris Suslowicz is offline
Junior Password Gnome
 
Join Date: May 2007
Location: England
Posts: 814
Default

Quote:
Originally Posted by kevin powles View Post
Hi Chris, Any pictures you may have will certainly help in this installation, It's seems a shame I cant use my original radio carrier in the bren carrier for the No11 set, Now I have to source the correct one for the 19 set.

kevin.
Can you post a photo of which mounting parts you have got in your carrier, please?

I can probably work out which bits you need from that (and maybe supply pictures so you know what to look for).

Best,
Chris
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sten Gun mounting kevin powles The Carrier Forum 10 04-07-10 22:13
Location of Variometer on a late Ram Kangaroo? kevinT The Armour Forum 6 21-11-07 06:28
Radiator mounting rampant rivet The Restoration Forum 8 18-05-07 17:27
Variometer Installation for T-16 horsa The Carrier Forum 0 08-04-07 21:34
Mounting new tyres sapper740 The Restoration Forum 18 26-11-05 00:07


All times are GMT +2. The time now is 00:36.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016