MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Restoration Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 21-11-18, 00:57
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default HUP restore in Sask

Hello
Im knee deep in this new vehicle , ive hit a road block with the transmission . It was full of water so im wondering if anybody has any gears for this
1943 Hup Pers-1
Chev sm420 trans
casting 590474
Thanks Anthony

and if anyone is wondering on a transmission color there is a lot of original kakki olive paint all over this one.
Attached Thumbnails
IMG_2773.JPG   IMG_2772.JPG   IMG_2774.JPG  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #2  
Old 21-11-18, 03:24
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

Are you sure that you have a SM420 transmission?
I have understood that the SM420 had synchromesh 2nd to 4th and I usually think of synchromesh as having helical, constant mesh gears rather than the straight cut gears in your photo.
Some online sources give the part number 590474 as being a 4 speed transmission as early as 1931 which feels early for a truck to have synchromesh.
Some characteristics of your photos resemble standard 4 speed of the CMP era but I don't find the part number 590474 in the CMP manuals I checked. The "retainer, clutch gear bearing" 591327 does appear in CMP manuals and is listed as 1938-46 in a Master Parts Catalog. (590474 doesn't appear in the same master parts catalog applying to 1929-48 so may be a later than '48 number).
I think that GM basically assigned part numbers sequentially so early parts have lower numbers, parts designed at the same period have similar numbers etc.
I hope I'm not making you as confused as I feel.

Looking at your photos, I wouldn't give up on the gears. I suspect a good wirebrushing or scotchbrite pad buff would make them usable (subject to inspection after cleanup). Some simple old mechanisms are remarkably tolerant of imperfections.
Reply With Quote
  #3  
Old 21-11-18, 03:33
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,091
Default Looks good

Unless there is some damage I don’t see it looks pretty good. I recommend getting a new from input shaft bearing a sealed version and pull out the neoprene seal on the inside. Check the cage bearing and I often see the rear seal on eBay.
Reply With Quote
  #4  
Old 21-11-18, 05:29
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Rotten teeth

So it isn't a sm420 but the earlier 31-48 predecessor.
Normally I would buff up the gears and carry on ,but the rust ate 3 teeth off third and the rest don't look much better.
If I was to run this pitted up gear set it would be so loud in the cab you'd need good ear plugs .
Anthony
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #5  
Old 21-11-18, 07:51
Tony Smith's Avatar
Tony Smith Tony Smith is offline
No1, Mk 2** (I'm back!)
 
Join Date: Feb 2003
Location: Lithgow, NSW, Australia
Posts: 5,042
Default

Although the CMP parts books list the transmission casing as being Pn 590524, it seems that 590474 is a common alternative.

I have 2 Chev CMP gearboxes with the casing number 590474.

The mainshaft 3rd gear is pn 590493, while the countershaft 3rd gear is pn 590502, both available NOS from a variety of sources.
Attached Thumbnails
IMG_7502.JPG   Original-1.JPG  
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should!
Reply With Quote
  #6  
Old 21-11-18, 15:13
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default I would not give up on this box

Hi Anthony

I would not give up on this box, rust on gears often looks far worse than it is. Two of my CMPs had transmissions as bad or worse than this, and they both clean up and have many thousands of miles on them after going back on the road.

I started by removing the bearings then polishing each gear tooth with 3M rowloc pads, used old wheels with most of the abrasive worn off, with a very light touch, object remove and smooth the surface. I didn't try polish out the pits, leave the pits alone.

Take a look at the photos http://canadianmilitarypattern.com/C...ansmission.htm it shows, primarily, the transmission in my C60S as I started 1990 and then 2008 and 12000 miles later. When the main shaft got noisy and had to be replaced, new shaft and it ran for another 10,000 miles before breaking a tooth. http://canadianmilitarypattern.com/3...ansmission.htm

That time I got lucky and found a NOS gear box, can we say scarce as hens teeth. Yes, I did find a replacement gear and rebuilt the first transmission, which with three CMPs on the road sits on the shelf full of gear lube ready to go in.

Back to my point, if the gears and bearings areas clean up it will probably give many thousands of miles.

Keep us posted on your progress.

Cheers Phil

PS I'll look to see which of my photos need to be moved to MLU.
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #7  
Old 21-11-18, 16:38
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

When I rebuilt mine i put all new bearings in it and also a new rear seal. The rear seal has the sheet metal tabs spot welded to it. I also replaced my shift forks as they were worn. I found all of the parts on ebay.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #8  
Old 21-11-18, 17:57
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,091
Default

Quote:
Originally Posted by ahleeds View Post
So it isn't a sm420 but the earlier 31-48 predecessor.
Normally I would buff up the gears and carry on ,but the rust ate 3 teeth off third and the rest don't look much better.
If I was to run this pitted up gear set it would be so loud in the cab you'd need good ear plugs .
Anthony
Loud is normal, at highway speed I use a com set just to talk to the passenger. Straight cut gears in the transmission and transfer case will do that!
Reply With Quote
  #9  
Old 21-11-18, 18:50
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Gear closeup

Looks like this gear was on the meth pipe
Attached Thumbnails
IMG_2781.JPG  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #10  
Old 21-11-18, 19:45
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Yup the metal mice have been at them

Quote:
Originally Posted by ahleeds View Post
Looks like this gear was on the meth pipe
Yup those are definitely past the polish and put it back together.

Though back in the day my brother had a Model A where the teeth looked like that and some mechanic had carefully brazed and filed each tooth back to shape. But boy was it load, he replaced the gears.

That photo is a classic "it ran when parked"

Cheers Phil


Is that the only gear that is bad? Interesting because that looks like the 3rd gear lower cluster gear which is the same one that my C60S broke a tooth out of, which I was able to find a NOS gear and replace it.
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #11  
Old 21-11-18, 20:14
maple_leaf_eh maple_leaf_eh is offline
Terry Warner
 
Join Date: Mar 2004
Location: Shouting at clouds
Posts: 3,081
Default Advice from the cheap seats

Quote:
Originally Posted by ahleeds View Post
Looks like this gear was on the meth pipe
Hmmm? In your situation, maybe you want to invent a jig to hold the rotten gear and then stock up on good quality welding wire? Or, pause the project until you can source a better looking gear.


BTW, I visited Moosomin many times when driving East/West on No. 1. The namesake of my street in Regina, Harry Mullin VC, is buried south of town.
__________________
Terry Warner

- 74-????? M151A2
- 70-08876 M38A1
- 53-71233 M100CDN trailer

Beware! The Green Disease walks among us!
Reply With Quote
  #12  
Old 21-11-18, 20:58
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default Gears are available.....

Hi Anthony

Gear clusters are available....maybe not new but in good shape. I have opened more than one tranny over the years and although the box was half filled with water and bearings might have been pitted the gears were always good. Seals and bearings should be available from industrial dealers like General Bearing Services by size...OD and ID. A complete tranny from a junk yard may be much cheaper than a single gear retail....just remove the cover and spin the gear around for inspection. Easy to mail but expensive by weight. Sometimes the gears can be chipped or worn from lack of synchros but if not too bad can be dressed up with a grinding wheel. I have some available if you get desperate but postage from Ottawa, when they work, would be high.

Yours are beyond recovery and will no doubt chip and cause further damage to other gears.

Good luck and keep us posted by photos of your progress.
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #13  
Old 21-11-18, 21:58
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Just buy the individual gears NOS off of ebay. The MB-C2 manual gives a great run down on how to replace the gears. its very easy to do.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #14  
Old 21-11-18, 23:34
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default There are two different 3rd gears

Hi

In your search for a replacement gear check the number of teeth, if memory serves there are two different 3rd gears with different diameters and different numbers of teeth so you need the one you have to match the upper gear cluster.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #15  
Old 12-12-18, 18:10
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Found a rebuilt trans

Phoned up Asperline Transmission in Winnipeg and he had one sitting on the shelf .
Was rebuilt and left there 20 yrs ago.
Felt pretty lucky to get one that easily.
I gladly paid him 500.00
Attached Thumbnails
IMG_2809.jpg   IMG_2810.jpg  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #16  
Old 12-12-18, 23:57
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Good find

Hi

When I found a NOS transmission few years ago, it still needed to be taken apart and cleaned. Hope you can also find the parts to repair the other transmission, always good to have a spare, to use or as trading material for some other major part.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #17  
Old 13-12-18, 19:11
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Points

Rolled out the points tool kit
Not sure if it's ww2
Or home made but it's got everything
Fireing up the new engine
Attached Thumbnails
IMG_2844.jpg  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #18  
Old 13-12-18, 23:25
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default New rebuilt?????

Don't forget to use Zinc additive to the oil.....

Or HD diesel engine oil....

run at a fast 1000 rpm idle for at least 30 minutes to let things fit together.

Good luck

PS what plugs are you running???
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #19  
Old 26-05-19, 16:50
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Two into one

Finally looking HUP like
I will align the frames and weld it all together now
The front dash is original,the back body was a replacement.
This pile of parts was bought from cletrac last year
Attached Thumbnails
IMG_3820.jpg   IMG_3819.jpg  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #20  
Old 26-05-19, 17:15
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Some before pictures

Loaded for home
Attached Thumbnails
IMG_3823.jpg   IMG_3822.jpg  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #21  
Old 28-01-20, 00:37
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Body work

Some of the winter progresses on the HUP .
Burning through the grinder discs and mig wire.

Any chance someone has a spare RH door ?
Attached Thumbnails
IMG_5054.jpg   IMG_5053.jpg   IMG_5052.jpg   IMG_5050.jpg   IMG_5051.jpg  

__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
  #22  
Old 05-02-20, 00:36
ahleeds's Avatar
ahleeds ahleeds is offline
Registered User
 
Join Date: May 2010
Location: moosomin sask.
Posts: 134
Default Just in time

Found these beauties just in time .
Was all set to make a pair.
Attached Thumbnails
IMG_5124.jpg  
__________________
1954 GMC 211 , Restored
1941 F8, Restored
1942 F15A , needs box and restore
1944 C15A , needs box and restore
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
How To: Restore a Morris or keep fit Mike Kelly The Restoration Forum 63 11-07-18 10:38
Humbolt Sask. Eric B Tributes 5 13-04-18 03:40
So my employer wants me to restore this. Sean Dunnage The Softskin Forum 13 18-07-14 17:48
Two T16s to restore EricF The Carrier Forum 16 17-02-13 19:40
Cab 11 F15 for sale in Sask. Don Dingwall For Sale Or Wanted 4 28-06-06 01:27


All times are GMT +2. The time now is 00:22.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016