#1
|
||||
|
||||
Casting Parts
Hi all
I figured I would post somthing here instead of in the Carrier forum. The stuff that i use comes from a company called Alumilite. The website is www.alumilite.com They sell a variety of two part casting resins along with silicone rubbers for making moulds. The website is really good with lots of step by step photo instructions for a vareity of different mold makings and casting tips. For my own personal casting Im rather comfortable with the resins as I have been using them for about 5-6 years with my building scale models. However when I read about the rubber tail lamps falling apart after being out in the elements I figured I would have a go at making my own. I purchased an original from another forum member that was in really good shape for 60 year old rubber. My primary concern was that the silicone rubber used for making molds would bond to the rubber part. The silicone rubbers bonds perfectly to itself even if one is already cured. After many assurances from the people at Alumilite is used the HSIII casting rubber. This stuff has unbelievable give and can really bend without tearing. It was then just a matter of making a box and mixing up the silicone. Carefully poor the silicone into the box and then let it sit for the specified amount of time. i think I let is sit for about 48 hrs before I demolded the original. For the rubber itself Alumilite sells a product called Flex 80. It is a 2 part urathane casting rubber. Just pour two equal amounts and then mix for about 1 min. The simply pour it carefully into the mold. I demolded it in 1hr. The instructions say 30 min but I always wait a bit longer. The other important thing to remember is to the preheat the mold. I justt put it in the microwave for about 2min.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#2
|
|||
|
|||
Thats a cool site Jordan , I remember back in the day of using a vacum to do scale modling molds to copy armour tank bodys and parts I haven't done that in years, usta play around with casting in lost wax too.
GOOD SHOW LADDY! MIKE |
#3
|
|||
|
|||
Interestink......
So tell us more and show some pictures......
What would be the cost per unit should you be doing some volume (low) castings....??? how would the light socket fit in??? You may be on to something???? How strong is the rubber casting??? can it be used for the elusive round and square rubber bumpers on the front axle U-Bolt pads???? Booby Pein
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#4
|
||||
|
||||
Bob, I have a pair of those elusive rubber bumper available, I believe they are Ford front spring ones. PM if you like...
__________________
3RD Echelon Wksp 1968 M274A5 Mule Baifield USMC 1966 M274A2 Mule BMY USMC 1958 M274 Mule Willys US Army 1970 M38A1 CDN3 70-08715 1 CSR 1981 MANAC 3/4T CDN trailer 1943 Converto Airborne Trailer 1983 M1009 CUCV RT-524, PRC-77s, and trucks and stuff and more stuff and and....... OMVA, MVPA, G503, Steel Soldiers |
#5
|
|||
|
|||
Furd....Furd.....
....waht no rubbers for Chebbys.....
Seriously.... are they different than the Chev...???? I need some square ones for my front axle cab 11 ... I beleive larger C30 and C60 had a round di*** shaped rubber bumper... If what you have is the square one I will take them...... Sponge Bob Square pants
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
|
|