MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Carrier Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 19-03-18, 17:03
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default panzerjager bren project

starting my next project. going to build a pazerjager bren as used by the 3rd panzergrenadier division in Italy 1944. starting off with what i believe is a 1942 uc. it appears to have most of the drive line components, track and road wheels. no armor or creature comforts. this is what i hope to make it look like.
Attached Images
 
Reply With Quote
  #2  
Old 19-03-18, 17:06
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

here's what i'm starting with.
Attached Thumbnails
IMG_20131124_114258_589 bren.jpg   IMG_20131123_173048_559 bren.jpg   IMG_20131123_173228_891 bren.jpg   IMG_20131124_120619_728 bren.jpg   IMG_20131123_173119_071 bren.jpg  

Reply With Quote
  #3  
Old 19-03-18, 17:27
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

the engine has a rebuild tag on it, the date 1962. it will be interesting to see what is inside it.
Attached Thumbnails
IMG_20131124_114803_379 bren.jpg  
Reply With Quote
  #4  
Old 20-03-18, 04:32
Michael R. Michael R. is offline
Registered User
 
Join Date: Jun 2011
Location: Canada
Posts: 1,154
Default

It does look like you have portions of a lower hull Canadian production UC MK-I*. I wager the date in the engine rebuild tag may read 1952 instead of 1962? If I can be so bold to suggest a good start may be to remove and dispose of those upper front plates with something new and more correct appearing?

Best wishes with your project Leo. Have fun!

If you still have the truck, it may be able to transport the panzerjager bren project?

Last edited by Michael R.; 20-03-18 at 04:44.
Reply With Quote
  #5  
Old 20-03-18, 21:46
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

i'll have to check out the tag again. as for the armor it will need a lot of clean up. (thats why i'm here on MLU.) funny you should mention transport i recently saw a trailer made specifically for towing UC's. it was being towed by a FL60(?) sized truck and though i could do that. unfortunately we got more snow coming so it's going to be a few weeks before i move the UC out of storage and up to the work pad.
Reply With Quote
  #6  
Old 30-05-18, 21:11
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

took a pict of the rebuild tag. not sure what the date is at all.
Attached Thumbnails
20180527_190353 b.jpg  
Reply With Quote
  #7  
Old 30-05-18, 21:32
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

the space i need to do the UC is cleared. got it uncovered and ready to move it into position on the concrete pad. probably going to start with getting everything out and on the ground to see what i have. i'm sure what i don't have will be a bigger list. really looking forward to doing this. i'll get some more picts up as i start to disassemble it.
Attached Thumbnails
20180527_190208 b.jpg   20180527_190221 b.jpg   20180527_190346 b.jpg  
Reply With Quote
  #8  
Old 31-05-18, 06:33
Michael R. Michael R. is offline
Registered User
 
Join Date: Jun 2011
Location: Canada
Posts: 1,154
Default

Quote:
Originally Posted by leo tomaiolo View Post
took a pict of the rebuild tag. not sure what the date is at all.
Could that be:

211 Base Work Shop
6 6 51
Reply With Quote
  #9  
Old 09-04-19, 22:54
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

so i finally moved the carrier to where it needs to be to get worked on. went thru some of the parts that came with it and half of what i need is there. at least for the drive line it's pretty complete. used my 41 to move out of it's hole and into the garage. spent most of the winter going thru the engine and trany. bad news on the engine there are 2 large cracks in the block. 1 is thru the exhaust port so i scored a good block and will be sending it out to the machine shop in a month or two. next up is working on the steering/brake assembly.
Attached Thumbnails
bren 17.jpg   bren 16.jpg   bren move.jpg   bren 10.jpg   bren 11.jpg  

Reply With Quote
  #10  
Old 09-04-19, 22:58
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

here's some of the parts i got. body is pretty clean. there's some scabbed on plates that will need to be removed from the front armor.
Attached Thumbnails
bren 1.jpg   bren 5.jpg   bren 14.jpg   bren 9.jpg   bren 12.jpg  

Reply With Quote
  #11  
Old 22-06-19, 15:50
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

so it's been slow going with this project. much to my dismay the original block has 2 large cracks in it. 1 in particular runs thru the exhaust port and i don't believe it's reparable. i'm going to bring to a shop that specialises in block repair and see what they say. other wise the block looks to have been completely rebuilt and ready to go. in the mean time i pulled a block out of storage and could use that if it's not repairable. of course that block needs a rebuild.
Attached Thumbnails
bren 18.jpg  
Reply With Quote
  #12  
Old 22-06-19, 17:32
maple_leaf_eh maple_leaf_eh is offline
Terry Warner
 
Join Date: Mar 2004
Location: Shouting at clouds
Posts: 3,081
Default

Look up Metal Stitching. There is a company that will sell you drills, taps, jigs and fixtures to repair castings and/or machinings. The machinist drills a hole along the crack, sets in the pin of the fixture, and alternatively drills and taps holes. He screws plugs into holes with threadlocker and proceeds. Eventually the crack is filled with plugs.

Don't know how well they'll work in your application, but if you are looking at large $$ for a replacement block, this might be an option.
__________________
Terry Warner

- 74-????? M151A2
- 70-08876 M38A1
- 53-71233 M100CDN trailer

Beware! The Green Disease walks among us!
Reply With Quote
  #13  
Old 24-06-19, 09:39
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Personally I wouldn't try to fix one that has a crack from the cyl. bore to a valve seat. It would basically be a time bomb. You would never know when the stitching would let go, and next thing water is no longer where it's supposed to be.
I am sure guys will now tune in and say they fixed theirs way back in 1763 B.C. and it's still running like a clock, but that's me. I'd want mine to be reliable, so I'd start with a better block and not waste dough on the cracked one. Just an opinion from this ole mechanic.
I wish you better luck with the second one Leo.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #14  
Old 31-12-19, 17:46
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

still making progress. working on linkages and pivots. took the front armor off to get at the floor. the screws for the pivots were rusted good. so i had to tac weld the heads to remove the nuts.
Attached Thumbnails
bren 29.jpg   bren 28.jpg   bren 27.jpg   bren 26.jpg   bren 25.jpg  

Reply With Quote
  #15  
Old 31-12-19, 18:00
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

trying to remove the bearing clamp from the tub. the bolt is blocked from removal till i take the exhaust guards off. they needed to come off anyway, they will need some repair too. now with the tub empty it's off to the blasters. hope to be looking at primer and paint in the next couple of weeks. started to put together a list of what i need for replacement armor. coming up quick.
Attached Thumbnails
bren 24.jpg   bren 31.jpg   bren 30.jpg   bren 23.jpg   bren 22.jpg  

Reply With Quote
  #16  
Old 31-12-19, 18:15
Michael R. Michael R. is offline
Registered User
 
Join Date: Jun 2011
Location: Canada
Posts: 1,154
Default

easy-peasy. . . enjoy the journey Leo !
Attached Thumbnails
5234B66B-B6A6-40F1-A6E2-0DE9A54C4230.jpg  
Reply With Quote
  #17  
Old 25-01-20, 21:53
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

so after looking at the center divider i decided to make a new one as i think it will be easier than repairing what i have. the rivets came out surprisingly easy, not complaining. there was some damage to the strip that covers the seam on the floor. decided to cut out a section of strip and replace that too. there's a little rust on the hull floor but it's not worth pursuing. getting close to blasting time.
Attached Thumbnails
bren 32.jpg   bren 36.jpg   bren 33.jpg   bren 35.jpg   bren 34.jpg  

Reply With Quote
  #18  
Old 29-01-20, 07:39
Dave Newcomb's Avatar
Dave Newcomb Dave Newcomb is offline
Registered User
 
Join Date: Dec 2016
Location: nr Portland Or
Posts: 91
Default hanging a Ford V8 '32-48

From Fordbarn.com and the Early Ford V8 Club Please do not mount [hang] your Flathead V8 from the bellhousings '32-48. there are numerous examples of those castings failing and dropping the engines. The safest method uses an exhaust mount plate of 3/8th " steel. Purchase or fabricate yourself, and still fits your engine stand rotator socket. newc
Reply With Quote
  #19  
Old 08-02-20, 04:00
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

Quote:
Originally Posted by Dave Newcomb View Post
From Fordbarn.com and the Early Ford V8 Club Please do not mount [hang] your Flathead V8 from the bellhousings '32-48. there are numerous examples of those castings failing and dropping the engines. The safest method uses an exhaust mount plate of 3/8th " steel. Purchase or fabricate yourself, and still fits your engine stand rotator socket. newc
Since that picture was taken I made a side mount. And you can't see it but I do have a jack under the front of the block. But you are correct, hanging them by the Bell housing is sketchy.
Reply With Quote
  #20  
Old 22-02-20, 00:05
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

got my block back from being stitched. he did an incredible job. it needed a few spots done. ended up have to stitch in 2 of the cylinders. so he sleeved them after he was done stitching. he tested the block to 60 psi for 2 hours. judging from the amount of high hp block repairs he has done mine should be no problem. so next stop off to the machine shop.
Attached Thumbnails
block 8.jpg   block 1.jpg   block 3.jpg  
Reply With Quote
  #21  
Old 22-02-20, 00:13
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

here's some better views of the repairs. you can see where the cracks went in to the cylinder wall. all of the stitching is done dry. when they put sleeved the cylinder they used a chemical bonding agent to install it. using the bonding agent removes the stress of pressing a sleeve in. i was quite impressed and a happy camper.
Attached Thumbnails
block 2.jpg   block 5.jpg   block 6.jpg   block 4.jpg   block 7.jpg  

Reply With Quote
  #22  
Old 22-02-20, 00:18
leo tomaiolo leo tomaiolo is offline
Registered User
 
Join Date: Aug 2015
Location: waterbury ct usa
Posts: 101
Default

heading up to the American History Museum this weekend to get some measurements off of the U.C. on display there.
Attached Thumbnails
bren collings.jpg  
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sold: Unfinished Aussie LP2a Bren Carrier Project drcowie For Sale Or Wanted 7 21-03-17 11:42
FGT project Tony Wheeler The Restoration Forum 38 12-07-12 06:09
Universal/Bren gun carrier project for sale trader For Sale Or Wanted 6 26-09-10 01:00
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project Alain For Sale Or Wanted 1 21-02-07 00:11
Panzerjager Bren konigstiger The Carrier Forum 23 11-08-04 04:54


All times are GMT +2. The time now is 15:38.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016