MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Restoration Forum

Notices

Reply
 
Thread Tools Display Modes
  #421  
Old 20-06-18, 19:26
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default

Quote:
Originally Posted by Jordan Baker View Post
Bob, when you say you used Speedy Sleeves, did they replace the original leather seals? Do you have part numbers? I was checking the shafts and they have a visible worn spot where they would seal on the leather. I presume this is what the speedy sleeves would fix?
Hello Jordan,

If you go to http://www.skf.com/group/products/se...eve/index.html, one can read everything there is to know about Speedi-Sleeves, Choosing the right size and Installing and Removing SKF Speedi-Sleeve.

HTH,
Hanno
Reply With Quote
  #422  
Old 21-06-18, 02:50
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Thanks all. I’ve got my reading list and will figure out what I’ll use with regards to the speedi sleeves. All of the shafts have a worn grove so I’ll have to do something.

All of the casing parts are now clean ready for PORing tomorrow. They all soaked in the parts cleaner solution, then subjected to some power washing. I then sandblasted everything. After that everything was power washed again to remove the grit residue. Then I soaked them in Marine Clean, then another power washing. After this they were hit with Metal Prep etching solution. Now everything is so clean I’d eat a dry cracker off of them.

Tomorrow my plan is to spray with POR then top coat in the blue primer. I’m thinking I’ll probably do the final Army colour once final assembly is done.
Attached Thumbnails
4644E09E-69BA-48BC-8FFE-D4F7DE25D821.jpeg   94038D3D-0C77-4915-8A65-8BCD8CFEA530.jpeg   36017588-6171-4477-BE8A-F0DE0BD6D60F.jpeg   FDAB52F4-686B-43C7-8AB2-605762A5122D.jpeg   27AA1F9D-9D92-4318-9210-3F981FE34A90.jpeg  

__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #423  
Old 21-06-18, 04:40
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default Good grief......

Nice job.....

Keep in mind that the bearing races/cones will not go in where you have POR....either tape off the bare metal area or scrap the POR with a sharp Exacto blade.

Speedy sleeves go on bare metal with locktite.... any POR will make them almost impossible to fit as the clearances is so tight.

Make sure you wash your brass shims carefully and account for the paper gasket thickness in setting the preload. Each bearing should be able to rotate by hand ...otherwise its too tight. Same for the fully assembled T case it should rotate by hand when fully put together. \

Have lots of paper towels and solvent to repeatedly wash you hands during re assembly.

Can you imagine the poor guys doing this work in North Africa in between sand storms!!!!!! while being shot at!!!!

You should have been a surgeon.

Cheers

Cheers
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #424  
Old 21-06-18, 18:24
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Stopped off at a bearing shop today.

Myself and the guy behind the counter measured up the seals and shafts and came to the following modern parts. Parts are ordered and I should have them tomorrow morning.

Transfer Case
Modern oil seal part number is SKF 19360 QTY3
Speedi Sleeve is SKF 99193 QTY 3

Bearings as listed in the parts manual.
Timken 332. QTY 6
Timken 339. QTY 5
Timken 342-S. QTY 1
Timken 14274 QTY 2
Timken 14137 QTY 2
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #425  
Old 22-06-18, 19:39
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Spent yesterday and today painted the transfer case parts. First in DOM16 ( Cnd version of POR15). Then in tie coat primer. Today was the final colour of SCC2. I also picked up the order of Speedi Sleeves and oil seals. I’ll give the paint a few days to harden up before installing the seals and the sleeves. Next week I should have the bearings and cones. I also had all the fasteners from the case in a tumbler with blasting grit in order to clean them up. I left it running for about 20hrs. Followed up with a quick buffing on a brass wire wheel they are good to go.
Attached Thumbnails
171C6F4F-912C-4D9D-8C27-A934900E432B.jpeg   7EE0270E-3934-4C56-ACFF-C627AFA3844C.jpeg   6AE5629D-BFA0-47E7-89E5-549E219F96AD.jpeg   822771A4-09DD-49B5-A8C0-357EC3711053.jpeg   AADD71D6-DE85-4D2E-ADEC-269BD95D4057.jpeg  

__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #426  
Old 22-06-18, 21:19
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default Congrats..........

Fantastic job!!!!!!!
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #427  
Old 27-06-18, 01:17
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

All my new bearings arrived yesterday so I made a quick run to the USA to pick them up. All went smoothly crossing the boarder both coming and going and I was home in no time.

Today I began disassembling the shafts and gears to clean them up. All has gone well except for the idle shaft. I don’t have the special tool for removing the speedometer gear. It’s tool J1737. I suspect it is simply a tool shaft that has matching female threads of the speedometer gear to screw on. I did try a bearing removal tool and it chipped part of it.

I’m not sure if I’ll need to source a new one or not.

I believe the GM# is 1811722

I see from the LWD site they have a Ford part that looks the same. Part # C01Q-17285-A. Does anyone know if they cross over?
Attached Thumbnails
E36C855E-6157-4CE7-8110-A7B058E7522E.jpeg   57533869-22B0-4993-ABD9-D9290216716C.jpeg   E51D7625-C693-431F-B28E-3F9DB4596EA8.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #428  
Old 27-06-18, 04:37
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

Your image of the tool is the one I see in MB-C2. MB-C1 shows a 2 armed puller, but gives the same tool number as shown in your image. Odd.
Based on the image, I would have interpreted the gear involved as being the spiral type mounted to the end of the transfer case idler shaft. I'm not expert but would interpret this as the driving gear and the smaller gear that engages both this one and the speedometer cable as the driven gear. (Both fall in parts group 4.337 so the diagram doesn't make it clear which is which.)

The gear I think of as driving, Chevrolet number1809534, is listed in a Ford parts book as equivalent to C01Q-17285-A and is described as having 4 teeth while a couple of other driving gears with only Ford part numbers are described as having 5 teeth. I think this is the gear you mention on LWD's site: https://www.lwdparts.com/product/gear-speedo-driven-2/ which seems to be the one listed as being common to the Chevrolet. LWD have another listing for a speedometer gear, driven that is the other part of the speedometer gearing https://www.lwdparts.com/product/gear-speedo-driven/ Be cautious with terminology to be sure you get what you need.
C01Q-17285-A is listed as appling to F15A, F30, F60S, L, H and FGT. 1809534is listed in Chev parts books as suiting C15A, C30, C60 S, L and X and CG. I didn't check any of the armoured vehicle books.

This gear is listed in the C15A0-04 parts list as one of the * parts, "peculiar to CMP vehicles", but is not so marked in the C60X-04 list. Puzzling.

Most of the non-CMP parts books I have seem to treat the driving and driven gears as items to be ordered as a matched pair rather than individual gears. These sets are all 6 digit numbers instead of 7 digit, suggesting earlier the CMP parts may be later (possibly by being designed to match the transfer case shaft instead of the transmission output shaft as in 2WD civilian pattern trucks. The Modified Conventional Pattern Chevrolets seem to follow the civilian method of treating the gears as "gear unit, speedometer drive".

How badly damaged is your gear? Any chance the driven gear rides on the part that escaped damage?

Last edited by Grant Bowker; 27-06-18 at 04:53.
Reply With Quote
  #429  
Old 27-06-18, 06:00
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Thanks for the help. My bad on the other part number. I read off he wrong line in the parts book when I was typing out my post.

The worm gear on the end of the idle shaft should be GM 1809534 Gear Speedometer Drive ( 4 teeth). From what you have, this part is the same as the Ford C01Q-17285-A?

Also here is the picture of different tool for removing the worm gear.


I stopped off at the shop tonight and we might be able to make a copy of the puller as found in MB-C2. He didn’t think where I had the small chips would be any issue as the other gear should just be riding in the middle.
Attached Thumbnails
D8EFB2B3-08AE-4111-A6B6-83CBC01A2E5F.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #430  
Old 27-06-18, 06:08
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

There does not appear to be anything special about that puller. I'm pretty sure I have that in both OTC and snapon.

I think a small to medium bearing puller (the plate type that has two halves) and a little heat from a propane torch would make quick work of that job, and provide much more support to the gear.
Reply With Quote
  #431  
Old 27-06-18, 06:11
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

I tried the plate type of bearing/gear remover and it quickly chipped the bottom of it so I stopped. I’ll try some heat on it tomorrow.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #432  
Old 27-06-18, 10:28
David Herbert David Herbert is offline
Registered User
 
Join Date: Mar 2010
Location: Ayrshire, Scotland - previously Suffolk
Posts: 547
Default

Quote:
Originally Posted by Jordan Baker View Post
I tried the plate type of bearing/gear remover and it quickly chipped the bottom of it so I stopped. I’ll try some heat on it tomorrow.
Did you use it flat side to the speedo drive gear ?

David
Reply With Quote
  #433  
Old 27-06-18, 11:24
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Jordan,once again, no knowledge on my part. What does the nut behind the gear do?
Can you use it to push the gear a bit?
If you heat the gear, a quick heat like oxy accetylene will get you the gear hot without the shaft getting hot at the same time. If you use the ring gear fitting method of using a wooden match to check the heat. That is, do not heat past the point where a match will char or "slips' easily sideways (loss of friction)
Something like a chain vicegrip might swing it off, when it is hot. I hope this lot helps.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #434  
Old 27-06-18, 12:11
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

A PDF of the pages on speedometer parts from Ford book SE 39-42 is attached to let you confirm.
Attached Files
File Type: pdf Speedometer Pages from SE 39-42.pdf (71.3 KB, 13 views)
Reply With Quote
  #435  
Old 28-06-18, 23:52
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Transfer case gears are all done. Well almost, just waiting for a speedometer drive worm gear to arrive from Holland. The original one chipped the threads while being removed. All new bearings, everything taken apart and cleaned up. Bearings were all dipped in oil before assembly. I’m currently just working on installing the new bearing races back into the case and cover. I also assembled the declutch shaft and carrier.
Attached Thumbnails
3101F79F-D46A-48FE-AD61-F978936225A8.jpeg   082FA4B2-7045-4425-95C0-EC600C2B6006.jpeg   E045B41D-F5B5-497D-8665-43F906D98918.jpeg   44C375B7-6AD9-475D-8008-88DB2A3282F8.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #436  
Old 29-06-18, 00:12
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default Amazing size of gears.....

When you consider the limited 85 BHP..... of all the T case I have opened the gears are always in good shape.

Another alternative to dipping the bearings is to inject some molyb. grease with the needle of the grease gun into the bearing cage.....then spin by hand to coat evenly...... messy but it works and at least they do not start dry.

Good job Junior!!!!
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #437  
Old 29-06-18, 02:17
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Jordan, that speedo drive worm gear (as someone has already said) will be fine to use. There will be no tooth load where the damage is. It would be good to dress the edges where the damage is.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #438  
Old 29-06-18, 03:57
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

I’m playing it safe and have a new speedometer worm gear on the way. I was thinking the chips shouldn’t be an issue, however when I lined up the other gear the teeth do pass over the one chip. Considering everything is opened up right now it’s easier to replace with NOS now versus down the road.
Attached Thumbnails
11FF4B93-F55B-4D5A-AEF6-EBB19B5B2E81.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #439  
Old 29-06-18, 05:05
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

Good on you for waiting, but I would concur with the others. The actual load on that pair of gears is so minimal, they usually make them out of plastic these days.
Reply With Quote
  #440  
Old 30-06-18, 01:26
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,517
Default

Jordan

I was just out in the shop and there sitting on the bench is a factory box with 2 GM 1809534Gear, speed. If you want me to, I can express post one to you (you would likely not have it until Thursday due to the Canada day Monday) but it's yours if you want it. Not being a chevy guy, I don't need one back.
Reply With Quote
  #441  
Old 30-06-18, 01:45
Stewart Loy Stewart Loy is offline
T-16, C15A
 
Join Date: Feb 2003
Location: Out in the woods near Woodstock, Ontario, Canada
Posts: 881
Default Closer than that!

Jordan,

If you want it, you can have the old t-case that was left behind when I parted out an old truck many moons ago.

Free to a good home - some heavy lifting is required.


Stewart
Attached Thumbnails
b.jpg  
Reply With Quote
  #442  
Old 30-06-18, 06:20
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Thanks guys. Ill send some PM’s in the morning. I’m headed to bed as work starts earlier enough. (Yes I do actually work contrary to what some believe)
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #443  
Old 09-07-18, 21:25
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

The NOS speedometer drive gear arrived today and was promptly installed. I then finished putting the case back together. This rebuild is done and ready to be mounted back in the frame.
Attached Thumbnails
FCEEDF40-3778-4BEF-B28A-72DC64A672D4.jpeg   E3763FAE-76B5-4175-A447-FBB6CD8DB2AE.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #444  
Old 11-07-18, 19:34
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Today has been a driveshaft kind of day. I finished pressing out the Spicer U joints on the shop press. I have to say that the shop press has definitely earned its keep in the shop and it’s one of the tools I use a lot.

Everything is off to the blasting cabinet currently. Then I’ll be prepping for the POR treatment.
Attached Thumbnails
8B84F155-DD84-40D9-B949-1C3BD512C282.jpeg   9EBD2E93-BD4C-4A40-8EAE-376F63319664.jpeg   2D988D6F-0334-46FA-8CB7-356EA3305B06.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #445  
Old 11-07-18, 21:49
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Old Motor Pool Sergeant Advice on Drive Shafts

Hi Jordan


You probably already thought of this or have heard it before. Align all the grease fittings.



An Old Motor Pool Sergeant took one look at my drive shafts and said I'd done them wrong. He went on to explain that all the grease fitting should be in a line on each shaft so as to make greasing easier. Next time I did a drive shaft I paid attention to alignment and darned if he wasn't correct.


Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #446  
Old 11-07-18, 22:12
David Herbert David Herbert is offline
Registered User
 
Join Date: Mar 2010
Location: Ayrshire, Scotland - previously Suffolk
Posts: 547
Default

Good tip and so simple to do !

David
Reply With Quote
  #447  
Old 12-07-18, 00:59
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Yes i read that previous post while researching what to do and not do. But thanks for the reminder.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #448  
Old 15-07-18, 03:19
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Today I finished up with the final cleaning of the driveshafts and components. After the usual marine clean and metal prep I then hand painted them in DOM16. This is the Canadian version of the POR15. It is cheaper, UV safe and supposedly be top coated anytime after curing. The downside to me is that it’s only available in gloss black. Even with hand painting it will self level to a mirror finish. Today I took advantage of the very humid weather and after about an hr the DOM16 was just tacky. I then simply sprayed on the SCC2 paint. This will then bond to the DOM16 and be very strong.

Anyway the driveshafts are all painted. I just need to now get the Spricer U joints ordered and get things assembled.

One question, are the “washers” in the caps made from industrial felt? The caps are at the end of splines. None of mine had anything left other then the split metal washer. I’m thinking felt would be good for sealing out the dirt and grime yet retaining the grease.
Attached Thumbnails
A8B31B2D-9918-4D89-B8F8-6AC222987CEC.jpeg   A3A681DF-B359-4C52-95B9-C9157FD6AD64.jpeg   059F424E-883A-4E32-B83C-E9F89794359E.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #449  
Old 15-07-18, 03:25
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Lastly for today my friend Matt was over working on his project with some help from me. Anyway back to he truck, I took advantage of him being over so that I could try and get the transfer case back into the frame. We ended up removing the tool box and spare tire carrier, slid the transfer case under the frame on a dolly. Then using the shop hoist I was able to sling a strap and we lifted the case up and into the frame. In hindsight it would have been much much easier to do this before the cab and box were mounted on the frame. But you only live once and well everything can’t be the easy route. We did manage to get some bolts in place enough to support it without the straps and hoist. However we so far cannot get the two large bolts and spacer washers to line up. They are off about a 1/16” of an inch. I’m thinking I may have to use my porta power to force the case over just that little bit.

Lastly is there supposed to be some kind of a spacer where I’ve circled in he picture?
Attached Thumbnails
4B89DF36-DD8F-4372-B4C9-80ABE885FFE9.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #450  
Old 15-07-18, 06:09
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Jordan, I think a lot of the spicer seals are made of cork. The join cut has a long overlap as I remember. (remembering is not such a reliable function as it has been)
Are your spacer washers in the right place? If you took them from the lower mount and put them on the top mounts, does it all line up then?
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
1944 C-15A-Wire-5 Restoration RichCam The Restoration Forum 706 18-05-23 02:43
Sold: 1944 Chev C15A Wire-3 Don Dingwall For Sale Or Wanted 11 02-04-15 23:26
What was once 2, is now 1. (C15A-Wire-5) RichCam The Softskin Forum 3 30-12-11 22:49
photos needed for c15a wire 3 van body jason meade The Softskin Forum 5 10-08-11 06:29
Wire loom for C15A Cab13 Jordan Baker The Restoration Forum 19 28-08-06 03:42


All times are GMT +2. The time now is 00:20.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016