MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > The Softskin Forum

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 14-05-19, 22:56
Alex van de Wetering Alex van de Wetering is offline
Moderator
 
Join Date: Mar 2003
Location: Hoofddorp, The Netherlands
Posts: 2,670
Default CMP's and attaching trailers......

Maybe I am missing something, but I can't find anything related to hooking up trailers behind a CMP in my manual. Does anyone know of any period publications on this subject? Or pictures?

Putting the towing eye on the tow hitch is easy enough, but some trailers also have chains to secure them to the truck.....but where do these attach on a CMP? Also, the wiring for the rear lights...I don't think CMP's came with a socket for trailer wiring as standard?

I know these days restored CMP's are often pulling trailers. As per regulations, these trailers often have modern lighting and sockets...but what was the original setup like?

Alex
__________________
Chevrolet C8 cab 11 FFW
BSA Folding Bicycle
Reply With Quote
  #2  
Old 15-05-19, 03:17
Tony Smith's Avatar
Tony Smith Tony Smith is offline
No1, Mk 2** (I'm back!)
 
Join Date: Feb 2003
Location: Lithgow, NSW, Australia
Posts: 5,042
Default

I asked the same question here: Artillery light

Some good responses, but no documented references.
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should!
Reply With Quote
  #3  
Old 15-05-19, 04:38
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

The Cnd 10cwt trailer came with tail and brake lights. There was a cable on the front with standard US male plug. However nothing on the CMP to plug it into.

In the CMP Service Bulletin book there is a write upon trailer air brake line being installed on the CMP frame.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #4  
Old 15-05-19, 13:55
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default My C60L had a trailer light plug

Hi Alex

My Pattern 12 C60L had what I believe was original trailer plug unit on it when I got it. Though not in condition to use I have saved it. Will dig it out and photograph it. I don't think it was the same as that used on US military trailer of WWII.

As a practical expedient I have replaced it with US M Series plug receptacle. Though to get meaningful trailer lights I've gone over to a 12 volt powered trailer lights which pick up the 6 volt signal from the trucks through 3 relays which then power the trailer lights off 12 battery on the trailer. When using this system I use magnetic based modern lights, which means I can tow other people's trailers when needed.

On the topic of towing other trailers, remember that CCKWs had a pintle hook that rotated, so the lunet was fixed. The size of the lunets of several WWII trailers I've towed is very tight on my C60S which means when towing on rough ground a lot of twistingredients gets put on the trailer tongue. Not a problem on the road.

As to the safety chains I just cross them under lunet an hook them in the tow eyes on the frame ends of my C60S and C60L trucks.

Most of my trailer towing is of my M5 generator behind my C60S Radio truck, which is narrower than the truck to the point that it cannot be seen in the mirrors and it is light enough that the truck doesn't notice pulling. But is just heavy enough to feel it when braking. Towing heavier trailers with CMPs does take thought, I've towed fully loaded water buffalos and you real know those are behind you.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #5  
Old 15-05-19, 15:06
Patrice DEBUCQUOY Patrice DEBUCQUOY is offline
Registered User
 
Join Date: Jan 2004
Location: France
Posts: 26
Default

Hi Alex,

Please find enclosed some infos given in HMSO's "Data Book of Wheeled Vehicles"

Click image for larger version

Name:	l8MxwAF.jpg
Views:	20
Size:	641.2 KB
ID:	107408
https://i.imgur.com/l8MxwAF.jpg

Click image for larger version

Name:	qn84NKv.jpg
Views:	15
Size:	599.2 KB
ID:	107409
https://i.imgur.com/qn84NKv.jpg

Click image for larger version

Name:	xmEuDpN.jpg
Views:	17
Size:	463.0 KB
ID:	107410
https://i.imgur.com/xmEuDpN.jpg

Click image for larger version

Name:	T57bCla.jpg
Views:	14
Size:	408.8 KB
ID:	107411
https://i.imgur.com/T57bCla.jpg

Hope it helps,
Patrice.

Last edited by Hanno Spoelstra; 15-05-19 at 20:46. Reason: attached pictures
Reply With Quote
  #6  
Old 16-05-19, 12:16
Alex van de Wetering Alex van de Wetering is offline
Moderator
 
Join Date: Mar 2003
Location: Hoofddorp, The Netherlands
Posts: 2,670
Default

Guys, thanks for all your replies.

Tony, I had missed that thread. Interesting info.....especially the pictures that Grant posted of the bracket fitted below the hook. It looks to good to be make-shift if you ask me.....so that could be the proper bracket for lighting of an artillery light.

Quote:
The Cnd 10cwt trailer came with tail and brake lights. There was a cable on the front with standard US male plug. However nothing on the CMP to plug it into.
Thanks Jordan. So, I am guessing the socket does fit in the connector in the back of a Jeep?

Quote:
As to the safety chains I just cross them under lunet an hook them in the tow eyes on the frame ends of my C60S and C60L trucks.
Phil, that's also the only solution I could come up with.....I mean without fitting additional parts or modifying things. I can only imagine that towing heavy trailers can be a challenge!

From Patrice's scans I understand that the larger recovery tractors and trucks were fitted with proper brake facilities for the larger transporter trailers, but I still wonder about the 2 axle CMP trailers....the 20cwt single axle trailers, Jordan's 10cwt, but also US or British type trailers like the 1Ton Ben Hur and 1/4ton US jeep trailer.
They can be seen being towed behind CMP's in period pictures, so maybe if there was no standard connection for the lighting, they just didn't bother and drove without lights???

Alex
__________________
Chevrolet C8 cab 11 FFW
BSA Folding Bicycle
Reply With Quote
  #7  
Old 16-05-19, 13:24
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Yes the Cnd 10cwt trailer plugs into the socket on the rear of the jeep. The trailer is also fitted out with Ford brakes and a larger master cylinder. Same as used on the big Ford trucks of the time. If I have a load in the trailer and im towing it and stop, Ill feel my jeep brakes first then once the trailer starts to slow Ill feel the serge brakes come on. It tows very very well behind the MB. For being such a heavy trailer for its size, it is so well balanced and i can move it around empty or loaded by my self.

Im planning on having it pulled by my C15a at some. I'll be installing a spare trailer socket on the CMP for the lights.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #8  
Old 16-05-19, 18:31
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

On the 4 wheel trailers that look like they have CMP bodies, the lighter ones use hydraulic brakes actuated by the drawbar (similar setup to the 15 and 20 cwt CMP trailers).
My 15cwt CMP trailer came with a few scraps of wiring on it, enough that I believe one circuit would have been to both left and right and the other right only. The wiring stopped before the drawbar so I'm only guessing it was tail lights and brake light (hydraulic pressure switch in the master cylinder).
Reply With Quote
  #9  
Old 16-05-19, 21:26
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Pictures of Trailer Light Plug Pat 12 C60L

Hi All


The following photos are of the trailer electrical plug that was on the rear of my Pattern 12 C60L when I got it. As you can see from the pictures it was in pretty rough shape. I was wired into the main wiring harness of the truck so it is likely original. It has four contacts so I would a guess that they are:

1. Ground
2. Brake/Stop Light
3. Tail/Rear marker
4. Blackout tail

Click image for larger version

Name:	Pat 12 Trailer Plug.jpg
Views:	7
Size:	120.2 KB
ID:	107418 Click image for larger version

Name:	C60L Trailer Plug_2272.jpg
Views:	7
Size:	646.0 KB
ID:	107419 Click image for larger version

Name:	C60L Trailer Plug_2274.jpg
Views:	6
Size:	778.8 KB
ID:	107420 Click image for larger version

Name:	C60L Trailer Plug_2275.jpg
Views:	6
Size:	937.2 KB
ID:	107421

Another thing to note is as this truck originally 16 inch rims the tow hitch is mounted between the frame rails, while my Pat 13 C60S has 20 rims and the tow hitch is slung under the frame rails. You really notice when you hitch a trailer up to these trucks. The Pat 12 C60L which now has 20 inch rims my generator trailer is tilled up a lot, while on the Pat 13 C60S the same trailer is towed dead level.

I was really surprised this morning went out to look for this to take a picture and it was on the shelf it should have been in correct box marked old Pat 12 parts.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com

Last edited by Phil Waterman; 16-05-19 at 21:32. Reason: Add information
Reply With Quote
  #10  
Old 16-05-19, 23:10
Lynn Eades Lynn Eades is offline
Bluebell
 
Join Date: May 2003
Location: Tauranga, New Zealand
Posts: 5,534
Default

Std QMC WWII USA plug, Phil (Jeep,Dodge, etc,etc....)
Post war common use, still there when the NATO plug was fitted. some NZ Army Land rovers had both.
__________________
Bluebell

Carrier Armoured O.P. No1 Mk3 W. T84991
Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6.
Dodge WC55. 37mm Gun Motor Carriage M6
Jeep Mb #135668
So many questions....
Reply With Quote
  #11  
Old 18-05-20, 14:05
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default trailer air brake line

Quote:
Originally Posted by Jordan Baker View Post
In the CMP Service Bulletin book there is a write upon trailer air brake line being installed on the CMP frame.
Here are some photos of the air brake line setup on a C60S in Sweden.

Doe anyone have a manual on this trailer air brake line setup?

Click image for larger version

Name:	chevrolet-4x4-cmp-30-2-st-12616-15882557174_redlined.jpg
Views:	10
Size:	838.6 KB
ID:	114146 Click image for larger version

Name:	chevrolet-4x4-cmp-30-2-st-12616-158825572912_redlined.jpg
Views:	16
Size:	822.9 KB
ID:	114147
Reply With Quote
  #12  
Old 18-05-20, 14:22
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

From what I can see, I would guess the truck shown above is more likely vacuum brake assist with vacuum brake for the trailer than air (pressure) brake. I base this on the little bit I can see of the lines to the cylinder and under the cab. The flexible connections look like simple hose clamped to tube which is more typical of vacuum than air brakes. Having said that, I believe air brakes of the WW2 era operated on lower pressure than current trucks so I could easily be wrong.
Reply With Quote
  #13  
Old 18-05-20, 15:48
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,000
Default

Scanned copy of

Service Information Bulletin #51, May 3, 1943
Trailer Brake Installation
Attached Files
File Type: pdf S.I.B.51 Airbrakes.pdf (1.13 MB, 29 views)
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #14  
Old 18-05-20, 16:56
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default

I know this is getting picky but that is a vacuum brake system for the trailer as opposed to air (pressure) brakes to go with the vacuum boosted system of the heavier CMPs. It does make sense to use the same power source for both. Also, I'm not aware of any CMP equipped with air (pressure) brakes except some trailers (usually towed by larger vehicles than CMP 3 tonners). As always, happy to learn more - even if it proves me wrong....

Last edited by Grant Bowker; 18-05-20 at 19:03.
Reply With Quote
  #15  
Old 18-05-20, 18:59
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default

Quote:
Originally Posted by Jordan Baker View Post
Scanned copy of

Service Information Bulletin #51, May 3, 1943
Trailer Brake Installation
Thanks Jordan!
Reply With Quote
  #16  
Old 18-05-20, 19:04
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default Trailer air brake line

Quote:
Originally Posted by Grant Bowker View Post
I know this is getting picky but that is a vacuum brake system for the trailer as opposed to air (pressure) brakes to go with the vacuum boosted system of the heavier CMPs. It does make sense to use the same power source for both. Also, I'm not aware of any CMP equipped with air (pressure) brakes except some trailers. As always, happy to learn more - even if it proves me wrong....
Grant, you must be right.

I thought I had seen pictures of the trailer air brake line setup on this forum before. I recalled it was for actuating trailer brakes, not boosting thr truck's brakes.

If it was a pressurised system, the truck would have to be equipped with a compressor but I see no signs of that.
Reply With Quote
  #17  
Old 10-07-23, 17:12
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default US trailer socket

Jordan found a wartime photo:

"Interesting detail on the back side of this C15A. Check out the US trailer socket."

Click image for larger version

Name:	358388543_10158959598411783_6390413979413751128_n.jpg
Views:	9
Size:	304.3 KB
ID:	135047
Reply With Quote
  #18  
Old 10-07-23, 17:18
m606paz m606paz is offline
Mariano Paz
 
Join Date: Jun 2009
Location: Buenos Aires,Argentina
Posts: 815
Default

My 1945 FGT have factory US Trailer Socket. Installation coming soon
Attached Images
File Type: jpg 20230710_122014.jpg (172.2 KB, 10 views)
__________________
Mariano Paz
Buenos Aires, ARGENTINA

1944 Ariel W/NG
1945 FGT FAT
Reply With Quote
  #19  
Old 10-07-23, 20:18
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is offline
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,400
Default

Quote:
Originally Posted by Hanno Spoelstra View Post
Jordan found a wartime photo:

"Interesting detail on the back side of this C15A. Check out the US trailer socket."
This is where the US trailer socket was mounted on my F15A. I doubt it was an original fitment, though.

Click image for larger version

Name:	IMG_1031.jpeg
Views:	7
Size:	91.8 KB
ID:	135053
Reply With Quote
  #20  
Old 11-07-23, 05:00
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,191
Default My failing memory tells me......

....that early CMPs had a single wire connection directly behind the tow hook partly shielded by a small piece of sheet metal....... the female connector would have been very similar to the trouble light socket installed in the dash of cab 11/12...... not enough wires to see where or how connected to the main wiring loom....but easy enough to approximate.

Grant may remember our findings such remains on old rolling chassis..... it may have only been used for brakes or for convoy lights????

Never seen any printed information.
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #21  
Old 11-07-23, 07:10
Grant Bowker Grant Bowker is offline
Registered User
 
Join Date: Jul 2006
Location: Ottawa, Canada
Posts: 2,285
Default trailer wiring plug found on CMP

Photos of what I believe is a CMP trailer wiring connetor are at http://www.mapleleafup.net/forums/sh...206#post256206 (13th post in the thread)
Reply With Quote
  #22  
Old 28-07-23, 22:48
Dave Schindel Dave Schindel is offline
Registered User
 
Join Date: Apr 2011
Location: S.E. Sask. Canada
Posts: 268
Default trailer wiring

this is what I believe to be the trailer wiring connector for a 15cwt trailer http://www.mapleleafup.net/forums/sh...ad.php?t=28524 . just posting FYI . Dave
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Attaching pictures try-out Hanno Spoelstra The Sergeants' Mess 8 23-03-16 18:04
Sold: Corio 1 ton trailers x 2 Lang For Sale Or Wanted 1 28-12-14 13:34
Studs double ended attaching axle shaft to hub Dale Jordan The Carrier Forum 4 08-08-13 11:56
Attaching a GS Box to the frame Jordan Baker The Restoration Forum 3 19-04-05 02:20
Two trailers 1 ton Dirk Leegwater (RIP) For Sale Or Wanted 0 17-05-03 14:38


All times are GMT +2. The time now is 20:53.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016