#1
|
|||
|
|||
Ford Crankshaft pulley needed.
I'm putting the correct engine in my Lynx and I'm having a hard time sourcing the correct crankshaft pulley with integral 4 bolt fan hub. any help or leads apreciated. Ford Flathead V8 pre 47.
Last edited by Harry Moon; 19-06-20 at 05:39. |
#2
|
|||
|
|||
Pulley
The picture looks like a 1939 or 1940 Ford car engine. It might be the same.
Paul |
#3
|
||||
|
||||
39-40 V8 Ford pulley/hub
Two sites Fordbarn.com or H.A.M.B. excellent for want adds and V8 parts also Vanpelts.com Dave
|
#4
|
|||
|
|||
I might be able to help out Harry, will check my spare numbers, Cheers Andrew.
__________________
Valentine MkV Covenanter MkIV Lynx MKI and MKII Loyd Carrier / English / Candian / LP. M3 Stuart |
#5
|
|||
|
|||
That would be great!
|
#6
|
|||
|
|||
Part
Harry,
Is this the pulley that you're looking for ? If so, PM me. I've got an assorted pile of left overs. Peter |
#7
|
|||
|
|||
Peter, the one you show is the wrong type. There are two different pulleys. One for the Mk1 , single belt as shown in Harry picture and the one for the MK2 which is double pulley and has re-enforced cast ribs on it, Cheers Andrew.
__________________
Valentine MkV Covenanter MkIV Lynx MKI and MKII Loyd Carrier / English / Candian / LP. M3 Stuart |
#8
|
|||
|
|||
Thanks
I don't think there is a balancer on the hub I'm looking for and only a single pulley. In addition has anyone come across this set up before?
|
#9
|
||||
|
||||
Housing ign
Hi; Looks like a water proof housing for the ign leads, on the front of a Ford V8. the distributor would be inside and braided ign leads attach to the housing. Is it Navy gray? Dave
|
#10
|
|||
|
|||
Distributor
Peter Duggan has the same set up on his Lynx. Send him a message.
|
#11
|
|||
|
|||
Harry , the box you show at the front is for shielded ignition, to stop static interference for the use of the radio set, typically the No.19 set. The leads are of the braided type to the plugs. Also see picture of the two types of crank pulleys for the different model Lynx's., Cheers Andrew.
__________________
Valentine MkV Covenanter MkIV Lynx MKI and MKII Loyd Carrier / English / Candian / LP. M3 Stuart |
#12
|
|||
|
|||
Run your parts book numbers and consider looking for the same water resistant shielded ignition assembly in the Ford Canada models of the Windsor carrier.
|
#13
|
|||
|
|||
Shielded Ignition
Harry,
I was very fortunate to find an NOS setup including braided cables which David Good installed when he rebuilt my engine. I have had the points since converted to a Pertronix kit. The shielding boxes were great for hiding the new configuration. Ross's suggestion that the same components were used on the Windsor carrier certainly opens up the potential parts sources. Peter |
#14
|
|||
|
|||
Kynx Pulley
Quote:
Last edited by Harry Moon; 21-06-20 at 05:09. |
#15
|
|||
|
|||
Great Information everybody
Thank You.
|
#16
|
|||
|
|||
As the Windsor carrier would have the fan extension with double pulley it will need the double lower pulley. The lynx with the single pulley must have had a different upper set up and single pulley water pumps.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Found: URGENTLY - Fan Pulley Ford Lynx 12V Generator | lynx42 | For Sale Or Wanted | 28 | 26-01-14 01:44 |
Wanted: 2 groove crankshaft pulley for M38/M38A1 | rob love | For Sale Or Wanted | 1 | 22-09-13 15:11 |
For Sale: Pulley for Ford Engine | peter simundson | For Sale Or Wanted | 0 | 16-08-12 15:14 |
Ford Water Pump Pulley | Darren Abbott | The Restoration Forum | 6 | 14-05-09 17:05 |
Flathead crankshaft pully needed | Mike Timoshyk | The Restoration Forum | 12 | 24-01-08 00:16 |