MLU FORUM  

Go Back   MLU FORUM > MILITARY VEHICLES > Parts/Sources/Prices

Notices

Reply
 
Thread Tools Display Modes
  #91  
Old 07-07-18, 14:10
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

For a C15a single speed Transfer Case

Transfer Case
Modern oil seal part number is SKF 19360 QTY3
Speedi Sleeve is SKF 99193 QTY 3
Shift shaft CR 5510 (or SKF) per Tony Smith

Bearings as listed in the parts manual.
Timken 332. QTY 6
Timken 339. QTY 5
Timken 342-S. QTY 1
Timken 14274 QTY 2
Timken 14137 QTY 2
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer

Last edited by Jordan Baker; 20-02-19 at 09:24.
Reply With Quote
  #92  
Old 05-10-18, 21:14
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default 2 speed transfer case seal

Does anybody have the part# for the small seal that fits on the shift shaft of the 2 speed transfer case. the one that goes on the shaft that attaches to the shift fork? I looked through this thread and I couldn't find a reference to it.

Last edited by Harry Moon; 05-10-18 at 23:40.
Reply With Quote
  #93  
Old 05-10-18, 23:39
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,229
Default try the dimension for a search...

Hi Harry

Was at a seal wholesaler today and they still prefer to search by OD/ID since numbers vary from manufacturer and over time..... once found they give you a choice of made by 'who' where (time) and/ or shipping cost.

You can probably figure out the ID easy enough but it will be a hell of a tight fit to measure the OD without taking your T case out....

Any body on the forum that has a 2 speed already taken apart for measuring....
I would suspect that the size for the two rods on the 2 speed and the one speed T case are the same...... need some time to read and compare in the parts manual..........

Mine where tight when I rebuilt my t case...... one of the few parts I did not have to change.

Good luck
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #94  
Old 06-10-18, 00:20
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default

This shaft is only on the 2 speed, and its apart on the bench.

Click image for larger version

Name:	IMG_0218.jpg
Views:	3
Size:	437.9 KB
ID:	102701
Reply With Quote
  #95  
Old 06-10-18, 09:08
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is online now
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,579
Default Seal part number lookup

Harry, if you can measure the shaft diameter and bore, go to http://www2.chicago-rawhide.com/ and click on "Seals North America Part Lookup".

Entering the ID and OD will give you a match from the current SKF seal catalogue, which in turn can be crossmatched to other manufacturers.

HTH,
Hanno

Quote:
Originally Posted by Bob Carriere View Post
they still prefer to search by OD/ID since numbers vary from manufacturer and over time.....
Reply With Quote
  #96  
Old 12-10-18, 00:00
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,229
Default oil/grease seals ........

Front brake drum.....C8, HUP C15A possibly others.....

SKF brand new..... part number 45150...... easy stock item at baring suppliers

Price as of Oct 2018 IN OTTAWA...... $136.39 INCLUDING TAX

Bob C
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #97  
Old 23-01-19, 04:07
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default

Quote:
Originally Posted by Harry Moon View Post
Freshening up my transfer case and I am replacing the seals.
It is the best advice to replace the original seal 50300 with two CR19360?
I put 2 in and it seems good.
Reply With Quote
  #98  
Old 23-01-19, 04:14
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default Front Brake Hoses for 6 inch front brakes

In building up the big 6 inch front axle with the big brakes I found the BH5931 hoses to short to cover the range of movement. I sourced BH6222 and they are the same length as the originals and have the same 5/8 thread end as well. I would recomend these be added to the parts list for 6 inch axles and they would be fine on a 5 inch axle as well..
Attached Thumbnails
IMG_0678.jpg  

Last edited by Harry Moon; 23-01-19 at 04:22.
Reply With Quote
  #99  
Old 23-01-19, 04:26
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

In the 5” or 6” axle. What is being measured to determine those sizes? Was one used on the 15cwt trucks?
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #100  
Old 23-01-19, 05:35
Bob Carriere Bob Carriere is offline
Moderator
 
Join Date: Mar 2003
Location: Hammond, Ontario
Posts: 5,229
Default The flange....... near the egg cup....

You can tell the 5 from the 6 from the flange cross section diameter....6 also has more bolts on the flange an the six has 6 bolts holding the top cap where the new departure bearing is located.......small C15a larger on C60 but there are exceptions Aussie C60 made in Canada late in the war has small axles and 16 in tires.
__________________
Bob Carriere....B.T.B
C15a Cab 11
Hammond, Ontario
Canada
Reply With Quote
  #101  
Old 23-01-19, 05:52
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Thanks. I see the differences now. And with 7min to spare I learned something new today.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #102  
Old 23-01-19, 16:55
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default spotting a 6 inch front axle

the easiest way to spot the 6 inch front axle with the larger brakes from the regular 5 inch front axle is at the hub. you can see the obvious bulge behind the lift ring on the 6 inch. not so obvious is that the wheel base is wider by a couple of inch's.
Soi far I have only seen the bigger 6 inch on FAT's and winch trucks.
Attached Thumbnails
IMG_0682.jpg   IMG_0681.jpg  
Reply With Quote
  #103  
Old 23-01-19, 17:08
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default Chevrolet master cylinders

Somewhere in the past there had to have been a Wagner/Raybestos/Delco part number for the original master cylinder. Anybody have that information? Might be useful in checking out old NOS stock we sometimes come across.
Reply With Quote
  #104  
Old 20-02-19, 05:59
Jon Bradshaw's Avatar
Jon Bradshaw Jon Bradshaw is offline
Registered User
 
Join Date: Jan 2009
Location: Prince Edward County, Ontario, Canada
Posts: 266
Default Seal sizes for transfer case

So I just pulled the seals out of my transfer case and they all appear to be the same size. One was so bad that the oil could have been drained out the gap instead of the drain hole.....
Two of them have a paper gasket behind the plate and they are in bad shape. The input one has a steel gasket in place and no paper ones. Any ideas on sourcing these paper gaskets?
The steel one looks fine although I am unsure if it would work without a paper one as well? If it was aluminum or copper I could see it being a crush type but it is definitely steel (has rust).
Thoughts on the gaskets? Should I just try to cut my own?
__________________
Many projects.....
Complete- Ford F8 truck
Complete-1956 Mk 2/3 Ferret
Complete- Bofors 40mm on carriage
Complete Reproduction- Vickers, Model 1937 Tank
Waiting restoration- 1950 Cambridge carrier, Ford CMP Water truck, 1943 Universal carrier, 1945 Dodge APT truck, Canadian C3 Howitzer, several parts vehicles and a few ideas.....
Reply With Quote
  #105  
Old 20-02-19, 09:16
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

I believe the steel one to be a shim. In the MB-C2 manual there is a very good detailed write up on the servicing and rebuilding of the transfer cases.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #106  
Old 27-02-19, 16:04
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Does anyone have a source for the through bolts used on these brass blocks and for the rear brake one? All of mine were rusted junk. Are the front ones the same as the rear ones?
Attached Thumbnails
23619BB3-0DE5-4CC1-81C0-E249E9F947AA.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #107  
Old 27-02-19, 22:29
Harry Moon Harry Moon is offline
Registered User
 
Join Date: Feb 2003
Location: Burnaby B.C. Canada
Posts: 1,110
Default Check these

https://www.macsautoparts.com/early_...ial-truck.html
Reply With Quote
  #108  
Old 27-02-19, 23:21
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,550
Default

NAPA has them complete with or without washers. You just need to know your thread size (usually 7/16-20 on most of the old North American stuff). Use the term "Banjo" bolt when talking to the (oldest) parts guy. I find the younger parts guys go crosseyed when you use common terms like this.

If you lived closer, I have a bin of about 50 of them out in the shed.
Reply With Quote
  #109  
Old 28-02-19, 00:02
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Ok great. I just wasn’t sure as there seemed to be different ones. I’ve got an old school NAPA in town. I’ll go visit them tomorrow.
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #110  
Old 18-03-19, 06:13
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Not truly a modern part but these are measurements from NOS felt seals used in the steering knuckles.

These are for the 6” ones but are the same for the 5” axles except in overall length.

The length is 24-1/2”
Attached Thumbnails
D138F294-70E8-4DB0-B362-6B5E2E27DBB5.jpeg   7D8D57F0-2CF4-493B-8F7A-9DAFE4BF6D42.jpeg   A0B37A09-F50A-4484-8C6D-676BBC462B61.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #111  
Old 18-03-19, 18:00
Phil Waterman Phil Waterman is offline
Moderator
 
Join Date: Feb 2003
Location: Temple, New Hampshire, USA
Posts: 3,927
Default Felt Steering Ball Seals

Hi Jordan

Thanks, good information to add to CMP Knowledge Base.

I've been using leather replacements since 1979 back then it was really hard to get information on CMPs. My first discussions with anybody who could answer questions was via regular mail. The first responses I got were from guys in Australia and New Zealand.

Cheers Phil
__________________
Phil Waterman
`41 C60L Pattern 12
`42 C60S Radio Pattern 13
`45 HUP
http://canadianmilitarypattern.com/
New e-mail Philip@canadianmilitarypattern.com
Reply With Quote
  #112  
Old 17-11-19, 00:31
Jacques Reed Jacques Reed is offline
VMVC
 
Join Date: Jul 2012
Location: Victoria Australia
Posts: 860
Default Transmission seal- Ford CMP

Good Day,

Here's another seal number that fits the Ford transmission rear seal to add to CR 21211

KOK brand Part No. TC 12167, rubber covered. They conveniently even give the dimensions embossed on the seal, in inches no less! KOK is a Taiwanese company so probably available worldwide. Cost $10 at the local bearing shop in Australia.

Cheers,
Attached Thumbnails
IMG_0280.JPG   IMG_0092.JPG  
__________________
F15-A 1942 Battery Staff

Jacques Reed
Reply With Quote
  #113  
Old 17-11-19, 15:05
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is online now
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,579
Default

Ian found out the hard way (= buying the wrong seal), that the Ford F15A seal front hub inner 5", Ford part number C01Q-1190B matches with SKF/ CR 49998 with ID 5" and OD 6.25"

http://www.mapleleafup.net/forums/sh...638#post264638
Reply With Quote
  #114  
Old 17-11-19, 23:17
Jacques Reed Jacques Reed is offline
VMVC
 
Join Date: Jul 2012
Location: Victoria Australia
Posts: 860
Default Buying the wrong parts

Hi Hanno,

It is easy enough to do, get the wrong part, I have a box or two of them, but measurements in the case of seals are the only true way to go. Even then, take the sample and, if possible, the part it is intended to fit to the shop. I did that with the rear transmission mount and seal and the bearing dealer confirmed my measurements.

Of course, in these days of mail order only without bricks and mortar shops it is often hard to compare parts.

I downloaded the CR Seals Handbook (SKF) and it is a wealth of information besides listing available sizes of seals and Speedi Sleeves. Recommended download for any restorer of any vehicle.

Cheers,
__________________
F15-A 1942 Battery Staff

Jacques Reed
Reply With Quote
  #115  
Old 18-11-19, 20:54
Tony Smith's Avatar
Tony Smith Tony Smith is offline
No1, Mk 2** (I'm back!)
 
Join Date: Feb 2003
Location: Lithgow, NSW, Australia
Posts: 5,042
Default

Quote:
Originally Posted by Hanno Spoelstra View Post
Ian found out the hard way (= buying the wrong seal), that the Ford F15A seal front hub inner 5", Ford part number C01Q-1190B matches with SKF/ CR 49998 with ID 5" and OD 6.25"

http://www.mapleleafup.net/forums/sh...638#post264638
Where did Ian's info come from? Was it the .zip file I posted in Post #10 on page 1, or is there another table? I no longer have Excel on my computer so can't read that table, but Keith's post #19 still has that info brought across on his webpage and it clearly shows C01Q-1190B to be a 5" seal and part number 49998. Where has the conflicting info come from?
__________________
You can help Keep Mapleleafup Up! See Here how you can help, and why you should!
Reply With Quote
  #116  
Old 21-11-19, 10:49
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is online now
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,579
Default

Quote:
Originally Posted by Tony Smith View Post
Where did Ian's info come from? Was it the .zip file I posted in Post #10 on page 1, or is there another table? I no longer have Excel on my computer so can't read that table, but Keith's post #19 still has that info brought across on his webpage and it clearly shows C01Q-1190B to be a 5" seal and part number 49998. Where has the conflicting info come from?
Hi Tony,

Going back through the releated threads the correct info was there indeed, but I did not help with muddling it up. The p/n I shared is correct for the seal with the dimensions shown, but that seal does not cross reference to C01Q-1190B. It now turns out I was wrongly informed and have been sold the wrong seal as as well...

Anyway, I have offered compensation and invited Ian to add his lessons-learned to this thread.
Reply With Quote
  #117  
Old 21-05-24, 17:20
Hanno Spoelstra's Avatar
Hanno Spoelstra Hanno Spoelstra is online now
MLU Administrator
 
Join Date: Feb 2003
Location: The Netherlands
Posts: 14,579
Default Rebuild Kit for Ford master brake cylinder

Ford master brake cylinder, 1 1/4" bore: current part number of a Rebuild Kit is 91T-2004-A, 91T-2004.
Click image for larger version

Name:	91T-2004.jpg
Views:	0
Size:	19.7 KB
ID:	137653


These kits seem to be quite easy to source in the USA, Canada and the UK, but I could not find a rebuild kit closer to home - until I remembered this:
Quote:
Originally Posted by Hanno Spoelstra View Post
If you have a Ford Master Cylinder needing a rebuild - the seals and pistons etc. are the same as on other American trucks like the Dodge WC-series for example.
As Dodges are very common here in The Netherlands it was much easier to buy a rebuild kit off the shelf, e.g. at Staman Trading:
https://staman.nl/product/kit-repair...ylinder-dodge/
Click image for larger version

Name:	KIT-dodge.jpg
Views:	0
Size:	18.3 KB
ID:	137654
Reply With Quote
  #118  
Old 15-06-24, 05:06
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Applicable to the Otter, C15TA and I believe the Fox AC and C60X transmission.

4.319 2075286 Seal, Mainshaft Rear Bearing Cap Oil

Modern SKF / CR 17645
Attached Thumbnails
IMG_1937.jpeg   IMG_1938.jpg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
  #119  
Old 28-07-24, 14:43
rob love rob love is offline
carrier mech
 
Join Date: Feb 2003
Location: Shilo MB, the armpit of Canada
Posts: 7,550
Default

I had to do a rear U-joint on an artillery tractor (Chev) a couple days ago and found the U joint that was commonly referred to on MLU was too short. The U joint referred to equals a UJ331 (the 331 is a common reference and the spicer number is 5-1350x). Caps are 1.188 diameter and the height is 3.622

A little research led to the right U-joint. The caps are 1.188 diameter and the height from top to bottom on the caps is 4.187. They are spicer 1410 series U joints and use part number 5-1410X. Another common trade number is UJ330.

It may be that the number listed on MLU is for the smaller or earlier trucks. But the various cab13 shafts I have sitting here all appear to use the latter UJ330 (spicer 5-1410X) U-joint.
Reply With Quote
  #120  
Old 28-07-24, 15:56
Jordan Baker's Avatar
Jordan Baker Jordan Baker is offline
Moderator
 
Join Date: Feb 2003
Location: Hamilton, Ontario, Canada
Posts: 4,087
Default

Rob, these are the parts I had a heavy truck shop tell me where the same as what I brought in from my C15a truck.
Attached Thumbnails
IMG_2190.jpeg   IMG_2191.jpeg   IMG_2192.jpeg  
__________________
Jordan Baker
RHLI Museum,
Otter LRC
C15A-Wire3, 1944
Willys MB, 1942
10cwt Canadian trailer
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 13:37.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © Maple Leaf Up, 2003-2016