|
|
#1
22-08-05, 04:27
|
|||
|
|||
It followed me home......
.....Honey....can I keep it????
Last parts truck compliment of Don Bernie and his overzealous by-law officer...... formerly CC-2's main attraction..... Charlie F. it still has your pintle spring pack which I will save for you...... Last time a Cab 12 ever did 120kmp on the 407....... after a while I had to slow down.... you see the front fenders had quite a few nuts.bolts missing on the leading edge and they started bending back....slowed the trcuk down by at least 4oKPM due to wind drag..... so I stopped and being frsh out of duct tape usaed some HD nylon tie-straps and stitiched them back on....... NOw back up to 120kmp... I discovered the airfoil of the front fenders actually lifted the trailer... the faster I went the lighter the load.... at around 140kpm the trailer went up and lifted the rear wheels of the Furd.... so I switched to 4 wheel drive to keep it under control........ Pictures on the next 3 frames Bet you guys in Aussie land never saw that before.....too bad my hands were full and g=couild not take pictures...
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada 
|
|
#2
22-08-05, 04:28
|
|||
|
|||
|
Stitching
pic 2
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
|
#3
22-08-05, 04:29
|
|||
|
|||
|
Broadside
Cab 12 after a diet
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
|
#4
22-08-05, 04:48
|
|||
|
|||
|
View from rear window...
Last one.....
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
|
#5
22-08-05, 15:37
|
|||
|
|||
|
whats there looks good
Bob - Another good save, though stripped are the bits that are there as good as they look? The front fenders look good and the frame looks in reasonable condition.
Cheers
__________________
Phil Waterman `41 C60L Pattern 12 `42 C60S Radio Pattern 13 `45 HUP http://canadianmilitarypattern.com/ New e-mail Philip@canadianmilitarypattern.com
|
|
#6
22-08-05, 21:13
|
||||
|
||||
|
BOB'S USED CMP LOT
Bob,
I was kidding about having room for a Division's worth of CMPs at your place! It would seem that you are intent on filling the field...good on you!
__________________
RHC Why is it that when you have the $$, you don't have the time, and when you have the time you don't have the $$?
|
|
#7
23-08-05, 03:54
|
|||
|
|||
|
Meant to ask you Rob....
....can you help me cut down some trees to amke more room... I sure could use the firewood......
Phil..... what is there is not bad at all.... first the frame is a C15 that has been lenghten.... strange usually the shorthen the C60. The extension was done professionnally... very well done and clean... for me it has a very good floor plate... better than mine and it has the dash and buttons pattern. Complete front and rear axle.... you know my quest for good front axle parts for mine. Nose sheet metal has some good salvageable parts.... master cylinder may already be spoken for for Rob.... good spring hangers useable springs..... odd frame bracket.... nothing will be wasted...... traded... exhanged ......loaned out or whatever. Fenders look better than they look.... although I have seen worst bent up fenders before..... they have a few rust hole but the overall shape is there and can be patched up quite easily. For the time being it may serve as a mobile stand for Rob's HUP body until he can re-instal on his frame. Noticed how Don had installed regular 16 pickup trcuk tires on the CMP rims..... will probably do the same for yard mobility. Bob
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
 |
|
|
Linear Mode
