#31
|
|||
|
|||
Admin?
Any chance of changing the thread title to something like "SAR LP2A and MK1 rebuilds" |
#32
|
|||
|
|||
[QUOTE Need lots of parts so if anyone has bits for sale in Australia please let me know. I will put a WTB ad in the correct forum with a list.[/QUOTE]
Where are you in Aus, Glen? |
#33
|
|||
|
|||
East coast new Newcastle.
Can travel to pick up if required. Did 3600 Km this past week ferrying all the parts I bought from Lightning Ridge. |
#34
|
|||
|
|||
Slowly stripping LP2A hull number 4425 and gradually getting parts and supplies together.
Only have the diff assembly to remove from the hull before I can get it sand blasted and get paint on the internal section. Most parts have come off fairly easy and look like they will free up with a little work and lubrication. Used the, weld a nut to the stud method to remove sheared off bolts and that worked well for the most part. Some impact after the weld cooled also helped the more stubborn ones. Only have one threaded lug that was not recoverable. First engine ended up being only good for parts as one of the cylinders was too far gone to re bore and putting in a sleeve is a last resort, so back on the hunt for an engine to rebuild. It was only cheap so I got a heap of spare internals from it anyway. The gearbox has freed up OK so might have a win with that one. Tried a few methods of unseizing some of the worst track sections. Soaked in citric acid solution. not much changed Heavy hammering and flexing. not much changed Sat the track section on a low temp fire and then worked over it with hammer once cool. This got all of the seized links moving and allowed the pins to be punched out. Pins were heavily pitted. Found a place with 7/16" 4140 round bar so there will be new track pins if the trend continues of finding poor condition ones in the tracks so far. Were pins hardened to a known rockwell number? Getting some paint organised so I can protect items once they are reconditioned. |
#35
|
|||
|
|||
Quote:
The trouble with doing this is that it is likely to make the material of the links very brittle. That does depend on what they are made of and I do not know the metallurgy of LP track but most tank/carrier track that I have worked with is fit for display only if it has been heated. If you break a track at speed you nave absolutely no control of what happens next. A much better way is to submerge it in a bath of molasses for a few weeks. As this is a very slow process it will gradually eat the rust from inside the hinge joints in a way that a faster chemical process won't. It will do no harm at all and is cheap if smelly. A plastic 'wheelie' type garbage bin is ideal as a tank as you can get a reasonable length in and it has a lid to keep the smell in and vermin out. There are various threads about this on the forum. David |
#36
|
|||
|
|||
David, does M.C.I., B.S.S.309 mean anything to you?
Is it Malleable Iron ? That is a spec for British track links from Feb.1944. They tried all kinds of brews with Nickel etc in the early days, but settled on a std brew, I imagine the Australian link was made of a similar brew. I can't locate any info on the pin, but recall it was heat treated?
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
#37
|
|||
|
|||
I think of it this way, if track links were pure cast iron, then they would be brittle in it's normal state either hot or cold.
"Malleable cast iron" means it has had heat treatment up over 900 C to change the grain structure. In my opinion as a welder / metal worker, heating up to around 200 C would have minimal, if any affect on the grain structure. Especially if they are cooled gradually and not quenched. If you were to get them glowing red hot and then dump them into a tub of water then yes, problem. The temp of the fire was around the same as if you were cooking on a cast iron pan. That sort of temperature doesn't make the pure cast iron pans brittle so I don't think the effect on track links is as bad as might be thought. Having said that, I do accept that there is potential for a problem to arise if the metallurgy is not what we expect and will try the chemical options for a bit of a longer period to loosen links in future. |
#38
|
|||
|
|||
Carrier parts.
Welcome to the forum and the world carriers. The restoration of my carrier was mostly complete 10 years ago. I may be able to help you with some sispension parts.My carrier was upside dopwn in my yard for 35 years. I assembled it in 12 months and had it at Corowa in 2007 .
__________________
John Mackie (Snr) VK2ZDM Ford GPW- script #3A Ford Trailer M3A1 White Scout Car -Under restoration- 1941 Ford Truck (Tex Morton) F15A Blitz Radio sets- #19, #122, #62, ART13, and Command |
#39
|
|||
|
|||
Thanks for the offer John.
I think I will be OK for the suspension parts at this stage. I have a mate that has a spare set that he is going to help me out with, so hopefully the LP2 will be OK. I am still looking for a british set of rear suspension units though for the pommy Mk1 if you know of any around. As well as a few other pieces for both hulls. I've got a list of odds and ends that I am looking for in the for sale and wanted section if there's anything there you might have that's no longer needed. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Mystery ram rod | BCA | The Gun Park | 9 | 21-07-16 02:38 |
Who like a Mystery? | Tim Lovelock | The Restoration Forum | 19 | 14-05-13 23:50 |
Mystery Guy 4 x 4 | David_Hayward (RIP) | The Softskin Forum | 0 | 30-11-06 18:32 |
ID Mystery help | Tony Smith | The Softskin Forum | 12 | 13-10-05 17:35 |
Mystery | Keith Webb | The Armour Forum | 11 | 15-08-05 00:16 |