#1
|
|||
|
|||
Cab11/12 Chev inner fender panel measurements?
Did anyone ever draw up plans for the two panels displayed in the pictures?
Both are missing on my C8; one is the C-shaped panel that goes around the steering shaft/box....and I think is the same as used on C15 and others in the series. It should be easy enough to make. The other is the front-most part of the left inner fender......there might be some difference between C8, C15 etc....I am not sure. Apart from that corner I am also interested to know how far the horizontal piece extends toward the rad and engine....(the piece that is bent 90 degrees and welded to the inside of the missing piece and inner fender part) Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
#2
|
|||
|
|||
C-Panel
Steering box plate off my C15, which may help. I can't help with the fender plate though.
Owen.
__________________
1940 11 Cab C15 1939 DKW KS200 1951 Willys M38 1936 Opel Olympia MVPA # 39159 MVT # 19406 |
#3
|
|||
|
|||
Owen,
That's a great help. I tried printing out a 1:1 print of your second picture, but I might have scaled it a little, as there is a small difference with what I can read on the tape measure. Just for verifcation; is the overall size 7-3/4 x 5-3/4 x 4-3/4? By the way....is it fixed with normal nut and bolt to the inner fender panel?, as I don't see any captive nuts on my inner fender. Thanks Owen! Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
#4
|
|||
|
|||
C Plate
Alex,
I make it 7-31/32 x 5-25/32 x 4-7/8. If you PM me your address, I could trace round the plate on a sheet of paper and post to you? That way, you get the size/shape/position of the cut-out too. No captive nuts on mine either. So normal nut & bolt. Owen.
__________________
1940 11 Cab C15 1939 DKW KS200 1951 Willys M38 1936 Opel Olympia MVPA # 39159 MVT # 19406 |
#5
|
|||
|
|||
Measurements (inches) and photos of one of Bob Carriere's parts. Only one hole had a screw in it but all three look similar size, no cage nuts seen on this part.
|
#6
|
|||
|
|||
???????????
Hi Alex..... not sure what you are asking......????
The other is the front-most part of the left inner fender......there might be some difference between C8, C15 etc....I am not sure. Apart from that corner I am also interested to know how far the horizontal piece extends toward the rad and engine....(the piece that is bent 90 degrees and welded to the inside of the missing piece and inner fender part) Not sure if there is a difference between the arches of the C8...C15....C15a.... the inner fender pretty well follows the curve of the arch. I have taken some measurements and photos from a parts vehicle with no engine ...it is a cab 12 C15a. In your picture you have colored the front area in rust brown..... that section is spot welded to the side panel. Is it missing on yours??? Can you clarify what specific area you need measuring..... Here are some photos and can take more if needed. Cheers
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#7
|
|||
|
|||
Owen, Grant, Bob,
Thanks for all your excellent info! Attached is a picture of the C-panel I fabricated according to your measurements. I think I still have to tweak the 3 holes a little, though! Bob, your measurements are a great help. I agree....the panels might be a bit different between C8, C15, C15A etc., but I think the hole position and overall size is the same. My C8 only came with the rearmost inner fender part...the biggest section that fills about 120degrees of the area under the fender. I recently got the mid section from Stefan at LWD. It's not C8 though, so it will require some modification and fabrication of the frontmost part. I have had it blasted in the meantime (picture attached). The holes seems to line up with the arch bars and existing inner fender part. I think I will have to cut the lower folded section from the panel, to get a straight edge, just like the section to the right. Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
#8
|
|||
|
|||
Minor differences.....
Hi Alex
Minor differences due to he arches sitting somewhat lower on the frame of the C8. I still maintain that you cannot do a cab 11 without having a few spare parts trucks to rob or copy from. Mind you all the trucks I have are rusted in the same place so all the inner fender box panels, the one that traps dirt over the arches are/were rusted and had to be fabricated or seriously patched. At the bottom of the side panel the C15a has a small panel that closes the gap between fender and frame andthe part over rides the frame has a canvass strap riveted....do you have that on the C8?? I used canvass straps cut to size. Cheers
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#9
|
|||
|
|||
Quote:
I also note the funnels for the vents in one of your pictures. I fabricated those last week....what a pain! It seems the small hose between the funnels and inner cab panel/vent was also made of something canvas-ish (?)....what do you think? A rubber hose would probably work, but I wonder what the original material would have been. Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
#10
|
|||
|
|||
Tubing.....
Hi Alex
The tubing is canvass wrapped around a steel coil...... was very common in cars of the 50s for heater vents and defrosters in cars....now of course all is made from plastic. A number of restoration suppliers still offers the product but you have o find the right diameter, which I can't recall but can measure for you, held in place by light weight hose clamps. Careful if you order as they usually have a minimum length they will sell and all you really need is about 6 inches. They are not very visible once installed and any kind of tubing or large radiator hose would do. Mind you the real issue is how well they line up between the funnel and the neck of the fender...... typical in my case they were slightly offset so the flexible canvas tube worked better for me. Phil Waterman had to make is own as well... I had a few pairs to choose from and some had rust pit holes which I sealed with POR. As to their actual cooling efficiency... it's a joke on a hot Summer day. You might want to consider using painted rolled up cardboard ...... Cheers
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
#11
|
|||
|
|||
Similar material is used in aircraft. If you have a contact in aircraft maintenance, they may be able to let you have a couple of short lengths removed from service.... Another source is http://www.aircraftspruce.com/menus/ap/ducting.html
|
#12
|
|||
|
|||
Ah, that explains the remains of the thin wire wrapped around the old funnel! I have to see what's available here; I think most European cars at the time used cardboard duct, and obviously in metric size. I will need some 2,5inch hose.
Grant, that's a good idea! I have to check if I can fnd a similar firm here in Holland. Attached are two pictures of the C8 right hand side inner fender panel. It shows the rivets that used to hold the canvas. Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
#13
|
||||
|
||||
Quote:
https://www.rubberhuis.nl/product/277 They have hoses in other materials as well, search for "afzuigslang". HTH, Hanno
__________________
Regards, Hanno -------------------------- |
#14
|
|||
|
|||
Thanks Hanno.
I was looking at getting some here. http://www.afzuigenventilatieslangen.nl/ It seems to be quite similar to the link Grant posted....hose used in aircraft and also for race cars. They also sell through a webshop and also just 1 meter in stead of 4. I just can't make up my mind whether to choose black or the orange/brown stuff! The remains I found in my Chev are somewhat orange...but I am not sure if that's rust or the original colour of the hose. Black probably looks better though.... Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Chev & Ford Cab11 -15A | RichCam | The Softskin Forum | 23 | 13-06-17 03:18 |
Fender fit help needed | Dave Schindel | The Carrier Forum | 3 | 21-03-12 05:26 |
Looking For This Jeep Fender Bracket | JEEPBOY | For Sale Or Wanted | 0 | 27-09-10 17:23 |
can-am front fender for sale | mike mckinley | For Sale Or Wanted | 0 | 23-11-09 01:18 |
Rear fender skirt? | super dave | The Carrier Forum | 8 | 17-09-07 17:32 |