#1
|
||||
|
||||
parts identification
Hello
can some one help me to ident this parts , they are mot in my MKI parts book, so probably MKII parts. thank you Harlé Sylvain |
#2
|
|||
|
|||
Hello
can some one help me to ident this parts , they are mot in my MKI parts book, so probably MKII parts. thank you Harlé Sylvain the long clip for the speedometer cable is used on the MK-I* and MK-II*. the divisional wall cable cover, jump seat gravity latch, and bracket are right hand C31UCW. the Sutton harness adapter could be applied to a MK-I*, if so updated. while the starting handle appears to be portions from MK-II*, it has either been modified, or I am mistaken. the detachable pouch bracket/strap could be used on the updated MKI* to MK-II... but your example is 1944 dated and Canadian made. Last edited by Michael R.; 26-01-21 at 23:10. |
#3
|
||||
|
||||
The half pipe mounts on the division wall in the engine compartment behind the driver it is for the wiring / conduit and is a Mk2’ism.
__________________
is mos redintegro __5th Div___46th Div__ 1942 Ford Universal Carrier No.3 MkI* Lower Hull No. 10131 War Department CT54508 (SOLD) 1944 Ford Universal Carrier MkII* (under restoration). 1944 Morris C8 radio body (under restoration). |
#4
|
||||
|
||||
The long bracket at the back is a Sutton harness bracket for the driver, Mk2 again.
The other two smaller brackets appear to be seat latches for holding the seats up in the rear compartment.. again mk2. I am after a pair of those for my carrier.
__________________
is mos redintegro __5th Div___46th Div__ 1942 Ford Universal Carrier No.3 MkI* Lower Hull No. 10131 War Department CT54508 (SOLD) 1944 Ford Universal Carrier MkII* (under restoration). 1944 Morris C8 radio body (under restoration). |
#5
|
||||
|
||||
Just spotted Micheal R’s reply.
What he said...
__________________
is mos redintegro __5th Div___46th Div__ 1942 Ford Universal Carrier No.3 MkI* Lower Hull No. 10131 War Department CT54508 (SOLD) 1944 Ford Universal Carrier MkII* (under restoration). 1944 Morris C8 radio body (under restoration). |
#6
|
||||
|
||||
Hello
Thank you both for your kind answers. Is my picture correct? Best regards Harlé Sylvain |
#7
|
|||
|
|||
Clip, speedometer casing, long
Harlé, your part number for the long speedometer casing clip should read:
C01UC 105340. It was used on each of the four Canadian three-wheel UC models after serial #2084. Last edited by Michael R.; 26-01-21 at 21:51. |
#8
|
||||
|
||||
ok thank you for this precision , what is the MKII starting handle?
The clip has the number co1uc 10534c best regards |
#9
|
|||
|
|||
C01uc 105340
Quote:
MK-II* carriers have mechanical starters. The bent rod in your image may be attributed to the handle portion of the assembly, found at the floor on the divisional wall between the driver and gunner. It appears modified, or is not the handle at all. Last edited by Michael R.; 26-01-21 at 23:14. |
#10
|
||||
|
||||
Hello
Ok I undersatnd , I will have a look for the starting handle, for the clip the C of the reference must be a zero badly done. Thank you again Sylvain |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bren Carrier Parts Identification | RichCam | The Carrier Forum | 1 | 14-09-13 14:56 |
Parts Identification | Howard | The Sergeants' Mess | 6 | 11-04-07 12:25 |
CMP Identification 3 | Kuno | The Softskin Forum | 17 | 13-02-07 09:19 |
Help with identification | Redbeard45 | The Softskin Forum | 7 | 07-01-07 10:47 |
T16 Identification | jbledsoe | The Carrier Forum | 2 | 09-09-03 00:11 |