![]() |
#1
|
|||
|
|||
![]()
1) I'm looking for a #21 mounting frame for a WS19, any condition acceptable as long as reasonably complete.
2) Also looking for either 4 guy rope assemblies for the Canadian 34ft aerial, any condition, or photos or good dimensioned sketches of the triangular wooden blocks on the ends of the guy ropes, showing how the ropes are fed through the holes in the blocks. 3) Copy of an instruction book for the 34ft aerial. Ottawa, Canada |
#2
|
||||
|
||||
![]()
I had a original 19 set frame . I have the drawings , or sketches I did , Is the # 21 the normal frame ?
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad Last edited by Mike Kelly; 31-10-20 at 00:19. |
#3
|
||||
|
||||
![]()
...............................................
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
#4
|
||||
|
||||
![]()
John. I’ve got a few sets of the shock mounts that the tray requires.
$115. If anyone else is looking for a set send me a msg.
__________________
Jordan Baker RHLI Museum, Otter LRC C15A-Wire3, 1944 Willys MB, 1942 10cwt Canadian trailer |
#5
|
|||
|
|||
![]() Quote:
Thanks for the info, I have managed to find a complete one here in Canada, but the sketches are helpful |
#6
|
|||
|
|||
![]()
Is this what you're looking for?
|
#7
|
|||
|
|||
![]()
Hi George I am looking for a mounting frame.
Larry |
#8
|
|||
|
|||
![]() Quote:
# 21 was the later (green painted) version, probably less of a hazard, otherwise identical. All screw threads are Imperial (BSF), the strap tensioner is 5/16-in BSC (British Standard Cycle Thread), which I think is 26 tpi. Taps/dies are available from various model engineering suppliers in the UK. It may be best to make the knurled knuts out of stainless steel rather than painting or electroplating them. Best regards, Chris. Last edited by Chris Suslowicz; 26-02-24 at 01:57. Reason: Typo - there's always one! ("knuts" is deliberate.) |
#9
|
||||
|
||||
![]() Quote:
https://britishfasteners.com/threads-bsc I have also come across British Standard Electrical Conduit threads , mostly used on older electrical fittings. https://www.casa.co.nz/electrics/Con...it-Threads.htm
__________________
1940 cab 11 C8 1940 Morris-Commercial PU 1941 Morris-Commercial CS8 1940 Chev. 15cwt GS Van ( Aust.) 1942-45 Jeep salad |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
WS19 - B Set Aerial Base | Tim Bell | The Wireless Forum | 1 | 11-03-17 12:36 |
Suspicious WS19 aerial base on eBay | Chris Suslowicz | The Wireless Forum | 10 | 26-11-16 21:02 |
WS 19 mounting frame for Mk1 carrier | RichardT10829 | The Carrier Forum | 25 | 05-04-16 10:41 |
antenna angle mounting for WS19 | cpetronis | The Wireless Forum | 13 | 11-10-15 18:51 |
Brackets Aerial Base Mounting No 2 | Tim Bell | The Wireless Forum | 0 | 18-02-14 22:12 |