|
|
|
|
#1
08-03-10, 14:44
|
||||
|
||||
do my eyes deceive me or is that a linkage cover that is on the ground next to the front fenders ? the cover that sits at the base of the steering column infront of the driver ? if so i would love a pattern of this item
 the phrase "All the right bits" springs to mind with this carrier, what a wonderfull clean project to own ! i can feel myself turning green Richie
__________________
is mos redintegro __5th Div___46th Div__ 1942 Ford Universal Carrier No.3 MkI* Lower Hull No. 10131 War Department CT54508 (SOLD) 1944 Ford Universal Carrier MkII* (under restoration). 1944 Morris C8 radio body (under restoration). 
|
|
#2
09-03-10, 07:05
|
|||
|
|||
|
Richard
You mean the one behind the front guards, and yes, I would also like details, and more photos.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#3
09-03-10, 10:40
|
|||
|
|||
|
Dave
Here is the bolt for your fan extension.
I have included a pic of the Ford and Lucas generators.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#4
09-03-10, 17:34
|
|||
|
|||
|
Thanks for the pictures of the bolt, What is the overall length of it and I assume it is drilled and taped on the end to thread onto the stud on the intake ? I will have to see where I put that guard and will take some better pictures of it and post them.
Dave
|
|
#5
09-03-10, 19:47
|
||||
|
||||
|
cheers Dave if you could and perhaps take some measurements it would help us that need that bit a whole bunch...
Richie
__________________
is mos redintegro __5th Div___46th Div__ 1942 Ford Universal Carrier No.3 MkI* Lower Hull No. 10131 War Department CT54508 (SOLD) 1944 Ford Universal Carrier MkII* (under restoration). 1944 Morris C8 radio body (under restoration).
|
|
#6
09-03-10, 22:26
|
|||
|
|||
|
Hi Dave
Bolt length o/all 4.125 (4 1/8") Head 11mm(7/16") Head is 1.000" accross the flats. Tube dia.= 19mm(3/4") The hole has been drilled 76mm, but only threaded to 40mm
O/all thickness of square washer=8.6mm. 32mm high and 34mm wide. Round washer 4mm thick. The manifold stud looks like 9/16" UNF. Use a good bit of steel. A lot hangs off it. On another subject, I see in your 3rd picture of post #5. on the extreme right of the picture, you have some leather rear hull/actuator rod seals. I have one only, and have never seen them anywhere else. Are they easy to get in Canada? I also have a rubber version. See pictures. Is the leather bellows on the bisector pull rod still available N.O.S.?
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#7
11-03-10, 19:45
|
|||
|
|||
|
Here is some pictures of the park brake shield and when I get a chance I will try to get some dimensions written up. Lynn the rubber seal you could get from Brian Asbury and you can email him at: brian.asbury@sympatico.ca with I believe part # TL3615.
|
 |
|
|
Hybrid Mode
