CMP Ford F60S

RichCam · #1 29-11-11, 03:48

Guys,

Thanks for all of your positive comments and questions. I currently drive a 2009 F550 dually and I hear you all about the necessity of good (serious) brakes and a big enough engine to haul you out of a tight spot when you need it. I will look at a trailer AFTER we get the F60S running.
I checked the data plate before I left work today. It was manufactured Jan. 5th, 1941, Serial # 25938, Motor 3G-7408-F. I crawled underneath it, being in my warehouse, it wasn't an issue. It looked to have a winch plate mounted part way down the frame, just past the split differential. Hoist equipment looks original. Does it use the power take off to power the hydraulic pump? As well, the box bottom, sides and rear gate are all wood. Roof panels are solid and flat, no hatches. It did come with an engine crank handle and rifle bracket in the cab. If you have any other questions, feel free to ask. We will be bringing inside the workshop sometime in the next two weeks. Warehouse is ok for storage but its getting cold out there.
Regards, Richard.

Bob Carriere · #2 29-11-11, 03:58

Hi Richard

Don't be mislead by the winch crossmember mounting plates........all CMPs have them. The winch mounting crossmember was a factory stock issue rivetted in place when the frame was done. Those destined to have a winch were then ready for installation.

If you rtruck was an original tipper..... the hydraulic pump was probably driven by the PTO at the back of the transfer case. The same location that would have powered the winch .........tippers would not have winch and lifting device for the dump box....

That truck looks very straight and worth every effort to restore it to its former glory.

Don't forget the pictures as most of us are illeterate and love/need to see nice pictures.

Bob C

Keith Webb · #3 29-11-11, 04:02

Quote:

Originally Posted by Bob Carriere

Hi Richard

Don't be mislead by the winch crossmember mounting plates........all CMPs have them. The winch mounting crossmember was a factory stock issue rivetted in place when the frame was done. Those destined to have a winch were then ready for installation.

Bob C

Only Chev chassis came with the winch cross member. Fords did not unless factory equipped with a winch.

and from Richard:

Quote:

It was manufactured Jan. 5th, 1941, Serial # 25938, Motor 3G-7408-F.

I'm inclined to think the year date may be a mis-strike. The engine number indicates a 1942 build. I don't think even the cab 13 prototype had been built by January 1941.

Bob Carriere · #4 29-11-11, 04:17

..... to the Ford X-Purt ...........

My experience is limited due to my sheltered life as a devout Chebby Lover !!!!!!

....on the ID plate....could the 41 be actually a 44...?

Will need to crawl under the 42 F15a to see the difference.... once the ground is dry !!!!!

Very early pilots cab 13.....and HUP were around late 41(Dec) or January 42..... but I stand to be corrected again....

Bob

Ryan · #5 29-11-11, 04:56

Hi Bob, have a look here at this thread:

http://www.mapleleafup.net/forums/sh...ad.php?t=12724

Grant Bowker · #6 29-11-11, 14:30

As far as I know, all CMP dump bodies were hydraulically powered from the PTO (the transfer case PTO, not the transmission). This means that it is unlikely that there were any dump trucks equipped with a winch. (for the same reason - transfer case PTO already used for the 2nd rear axle - I haven't seen any listings for C60-X with a winch) This makes sense on another level - the electrical system on all trucks of the era, not just CMPs, didn't have the capacity of modern trucks to support loads like winches or snow plows and electric motors also were larger, heavier and I think less efficient due to advances in magnet technology. I think they would have preferred hydraulic over electric for applications that might get wet.

RichCam · #7 29-11-11, 16:29

Guys,

Thanks for all of the commentary. The pictures were taken when it was parked outside last fall, it is now inside - safe and dry. For those of you that prefer not to read, I will try and video a quick walk around, crawl underneath and include shots of the cab with a close up of the ID plate. I will then post this video to YouTube with the title "F-60S Tipper".

We will restore the Tipper to its original specs. You have convinced me that I need to chase down a FAT to haul the UC on a trailer or to winch it out of the mud.

I will post the link as soon as the video is up.

Regards, Richard