F60L Cab 12 truck

Ganmain Tony · #1 03-08-14, 12:38

Quote:

Originally Posted by Shane

Tony is this a common problem with the fuel line? Did you replace the copper lines from the tank to the fuel tap and then the fuel pump with the injector grade rubber hose?

Shane I cant speak for the blokes that drove them through the desert in WW2 but from personal experience thats what happened to me.

The original lines are steel but are covered in a fabric. They also have a couple of curls in them. Note at the top of this photo you can see the curl in the fuel line.
Admittedly this is a 2WD 13 Cab but i'm pretty sure it'd be the same in a 12 Cab...

So all the lines in mine are rubber from the tank to the tank tap to the pump to the carbie.

Also enables you to put a couple of in line fuel filters. Mine are on each chassis rail between the tanks and the tap.

Shane · #2 13-08-14, 14:17

Thanks Tony, still haven't made up my mind which way i will go but being able to put in more fuel filters sounds great. Have made the choice to turn her into a 12 volt rather than a 6 volt after talking to Colin Jones and lets face it he's been there and done it when it comes to flathead V8s and the positives out way the negative. Spent most of the today with Hugh Davis and my Dad putting the V8 back in, was easy work due to their help and the use of a forklift. In the last photo im missing the pin can anyone send me one so i can get on with the job it has a small hole at one end for a split pin to go through more than happy to pay just need asap. Thanks lads

20140813_130129a.jpg 20140813_130706a.jpg
20140813_154436a.jpg 20140813_163739a.jpg
20140813_161611a.jpg

Phil Waterman · #3 13-08-14, 21:50

Hi Shane

Try you local tractor supply or older tractor dealer. That's where I've found them in the past.

Cheers Phil

Mike K · #4 14-08-14, 04:43

Quote:

Originally Posted by Shane

In the last photo im missing the pin can anyone send me one so i can get on with the job it has a small hole at one end for a split pin to go through more than happy to pay just need asap. Thanks lads

If you cannot buy a clevis pin for that , somebody with a lathe could make one in 5 minutes

Mike

Keith Webb · #5 14-08-14, 06:33

I have a few NOS ones in different sizes, will need to check...

Shane · #6 14-08-14, 13:41

Thanks Gentleman for you advice. I do have one of the biggest tractor dealers not 100 meters from where i work so will give them a go..but please have a look Keith if you dont mind. Also does anyone have the item number for the FORD badge to go on the dash of a cab 12 from Macs Auto? :salute

Howard · #7 14-08-14, 16:55

Shane,
I cannot find my parts book at the moment (Jo is away... I cannot find anything) but I think the part number is 91A-16606.
01A-16606-C is the correct size and shape, but has red edging.
Check those numbers in your parts book before ordering.
If I can find my book before hand I will let you know.
Cheers
H

colin jones · #8 15-08-14, 10:35

Hello everyone! I don't want to hijack Shane's thread here but I'm re skinning his doors for him and making some hinges as well so I thought this would be the best place to show how I made them.
The hinges are probably quite hard to find but not too bad to make if you've got the tools. I had 2 pieces of 30mm blocks and milled a hole through the centre giving me 2 half round dies. The pin is 1/4" so I welded the pin to some plate to use as the former in the press.

Jacques Reed · #9 17-08-14, 02:45

Quote:

Originally Posted by Ganmain Tony

The original lines are steel but are covered in a fabric. They also have a couple of curls in them. Note at the top of this photo you can see the curl in the fuel line.
Admittedly this is a 2WD 13 Cab but i'm pretty sure it'd be the same in a 12 Cab...

Good Day Shane,

See attached photo of the loop in the fuel line at the LH side of my F15-A with the fabric covering mentioned. The loop allows for the flexing between the chassis and cabin at the rear cabin mount springs.
Not sure if my fuel lined are the originals but they are steel and seem to be very old. The fuel lines and fabric covering was on it when I purchased the vehicle 20 years ago.

I found a good substitute for that cloth covering for fuel lines and a very close match. It is bitumen impregnated woven electrical conduit and is available from Vintage Wiring Harness in Ringwood Vic. Slides easily over the 1/4" tubing. That same conduit material is also used on No.3 and No.5 HT leads where they cross over the inlet manifold from the distributor of the Ford V8 engine to prevent chafing and to protect the wire from the coil to the distributor.

Cheers,

Bob Carriere · #10 17-08-14, 03:41

.... thanks for the detailed answer.

I have a drill press and will try drilling my own jig. Will post my results.

On the home made little post you made.... they are available from Macs Auto and are made of weak pot metal like the originals. Yours will be much stronger and last longer.

To David D. yes all the extra weight on pulling yourself up into a cab 11/12 or cab 13 certainly takes it toll... and the driver's door always shows more wear.

Will beat a path to the metal shop on Monday for blocks of steel to make a die.

Cheers

Shane · #11 27-08-14, 13:08

Hello all

Thanks again for all your comments lads, and of course Colin Jones for his work.
Without doubt i need help with parts on my new toy if anyone can help. There is a lot missing so give me a yell if you know of any parts laying around to fit the 2 pounder.

20140826_174459a.jpg 20140826_230743a.jpg 20140826_174507a.jpg

Also the museum wanted to know if anyone could identify this..

20140827_161603a.jpg 20140827_161618a.jpg

Cheers Shane

Shane · #12 31-08-14, 04:01

Just a quick update of the cab 12. I have decided to transform her into a 2 pounder anti tank portee might as well as i have the gun. Would like to see photos of the tray the gun sits on if anyone has any and also the layout of boxes etc. Anyway here is a couple of photos of the resto so far and the not to be done for a couple of years resto.

20140829_165122a.jpg 20140829_165054a.jpg 20140830_141256a.jpg

Bought this a few days ago, at least i know what im in for

20140826_152813a.jpg 20140826_152808a.jpg

Hanno Spoelstra · #13 31-08-14, 08:58

Quote:

Originally Posted by Shane

Just a quick update of the cab 12. I have decided to transform her into a 2 pounder anti tank portee might as well as i have the gun. Would like to see photos of the tray the gun sits on if anyone has any and also the layout of boxes etc. Anyway here is a couple of photos of the resto so far and the not to be done for a couple of years resto.

Looks great, Shane!

As for the Portee, search this forum and the rest of the internet, there is quite some material available. I think John Belfield has a restored Portee, so you could get measurements off that one.

Looking forward to seeing it completed.

H.

ford+CMP+2pdr+gun+portee.jpg
Australian Ford CMP 2 pdr. gun portee

lynx42 · #14 31-08-14, 12:11

Hi Shane,

Tim Scrivens has a Cab13 2pdr. anti-tank portee. It looks to be much the same as the Cab12 from the back of the cab. You should be able to get the measurements of it.

corowa2009a 087a.jpg

Regards Rick