|
|
|
|
#1
12-06-15, 03:04
|
|||
|
|||
Fitting into a CMP....
Rest assured Chris the 261 will fit... bolts right in with no modificaton to the CMP BUT as Phil pointed out the water pump from a 216 with a suitabe adapter plate is mandatory.... and easily found on EBay.
Fitting into a cab 11 CMP requires a bit more finess... you have to use a Cab 13 draft tube and you will need to run a small distributor from a 216 as the later 55 to 61 rubs on the engine cover.... no such issues with the cab 13. I chose to use the original 261 flywheel with the HD 11 in. clutch plate....all rebuilt by Ottawa Brake and Clutch... of course I am running on 12 volts. I found an after market hot rod twin oil filter mount that accepts the modern PH 8... this gives me an additional 1.6 liter of oil......oil pressure 40 pounds at idle . Vacuum steady at 22 inches. The twin oil filters are mounted inside the frame on the pass. side and not visible. Had the original GM 1/2 in steel line refitted with modern rubber oil lines for the plumbing. Runs very nice. Ran a Rochester B for a while and dids not like the gas leaks an switch to a YF carter manual choke. Carbs were rebult by the Oak Brothers in Toronto they still use the old fashion flow bench to test and set up there rebuilt carbs. Cheers
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada 
|
|
#2
12-06-15, 03:25
|
||||
|
||||
|
Who said anything about a CMP???
__________________
3RD Echelon Wksp 1968 M274A5 Mule Baifield USMC 1966 M274A2 Mule BMY USMC 1966 M274A2 Mule BMY USMC 1958 M274 Mule Willys US Army 1970 M38A1 CDN3 70-08715 1 CSR 1943 Converto Airborne Trailer 1983 M1009 CUCV 1957 Triumph TRW 500cc RT-524, PRC-77s, and trucks and stuff and more stuff and and....... OMVA, MVPA, G503, Steel Soldiers
|
|
#3
12-06-15, 03:40
|
|||
|
|||
|
Perhaps.....
.... your skiddoo????
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
|
#4
12-06-15, 03:52
|
||||
|
||||
|
Nope... but it is a HMV
__________________
3RD Echelon Wksp 1968 M274A5 Mule Baifield USMC 1966 M274A2 Mule BMY USMC 1966 M274A2 Mule BMY USMC 1958 M274 Mule Willys US Army 1970 M38A1 CDN3 70-08715 1 CSR 1943 Converto Airborne Trailer 1983 M1009 CUCV 1957 Triumph TRW 500cc RT-524, PRC-77s, and trucks and stuff and more stuff and and....... OMVA, MVPA, G503, Steel Soldiers
|
|
#5
12-06-15, 07:59
|
||||
|
||||
|
Quote:
 H.
__________________
Regards, Hanno --------------------------
|
|
#6
12-06-15, 09:35
|
|||
|
|||
|
Lucky guess or what?
Maybe a little bit of inside knowledge there Hanno?
David
__________________
Hell no! I'm not that old!
|
|
#7
12-06-15, 09:52
|
||||
|
||||
|
Quote:
 H.
__________________
Regards, Hanno --------------------------
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Chevrolet CMP Engine variants | BSM | The Softskin Forum | 20 | 10-01-18 14:40 |
| Chevrolet 216 - engine bearings | Richard Farrant | The Softskin Forum | 12 | 30-07-14 01:02 |
| Australian Chevrolet 216 engine owners | Lionelgee | The Restoration Forum | 22 | 17-10-09 05:32 |
| chevrolet 216 stovebolt engine and box | malcolm erik bogaert | For Sale Or Wanted | 0 | 21-03-09 11:28 |
| Chevrolet engine bits | Maurice Donckers | For Sale Or Wanted | 2 | 20-08-08 10:48 |
Hybrid Mode
