New UCW project - Page 8

Petr Brezina · #**211** 31-12-16, 10:08

Hi David, at least they are from inox, so will propably last forever

Yeah Lynn, luckily I got this cover, may post some pics later!

Petr Brezina · #**212** 01-01-17, 19:50

Oil cooler is on the place, also rad provisionally fitted. And we also have had some fun

Happy New Year everyone!

Petr Brezina · #**213** 22-01-17, 19:57

We have had a very special moment today - hull and engine wedding

Petr Brezina · #**214** 29-01-17, 21:12

Working on the exhaust pipes. Slowly progressing.

Petr Brezina · #**215** 10-02-17, 18:05

Just came across this video on Youtube https://www.youtube.com/watch?v=yhCZ56g108E
Very nice, british made, Mk.II/III carrier, just as mine - I assume carrier is from the Netherland (?). Anyone knows these guys? Cheers

Petr Brezina · #**216** 12-02-17, 20:31

Working on the engine. Slowly getting there...

Petr Brezina · #**217** 19-02-17, 20:32

Again, few parts mounted, oil setup finished. Also instrument panel provisionally fitted.

Lynn Eades · #**218** 19-02-17, 22:42

Looking good Petr. I believe there was 1/4" thick flat rubber gasket fitted between the dash panel and the drivers front plate. This was to assist in preventing failure of the speedo cable and electrical shorts. Also I think there was a dome nut on the bottom dash panel bosshead screw to make life easier on the fingers of your right hand.
See if the dash panel top cover will fit well, with the rubber spacing the dash panel out out.

Those lower engine cover rails are a great modification. I wonder why it took so long?

super dave · #**219** 20-02-17, 06:59

Lynn is referring to this as I made one for mine.

Also I see you hooked up the oil cooler lines up to your engine but I don't see a bypass valve, Do you have one for your carrier ??

Petr Brezina · #**220** 20-02-17, 09:38

Thanks guys! Yes, Im aware about this spacer between instrumental panel and front plate. British carriers used a bit different setup, there are two separate spacers left-right from Langite (which is compressed cork gasket I believe). Actually, you can see my spacers in the upper corner of the picture - they will go on the proper place eventualy. And thanks for heads-up about the dome nut, Lynn - my fingers are grateful to you

There is no bypass valve visible, because my engine uses a bit different setup - there is built-in bypass valve - see my sketch. Seems to be clever to me, hopefully it will work properly

Lynn Eades · #**221** 20-02-17, 10:20

Petr that is a bit different. Can you tell us about your engine? I've never seen that before.
There are so many differences in your late carrier and very few of them seem to have survived.
Does your dash panel have the four fuzes in the top?
I am surprised to see the white faced CAV ammeter. I thought it was an early British carrier thing. There are not many carriers that don't have the drop down bit for the Temp. gauge. It must have been a Dagenham Ford thing. My AOP is the same. It is July 1941. Much earlier than yours. Mine still has the two square holes in the rear plate but the air was ducted up through the rear deck, through a damper (like a fire) and out a mesh screen at the the level of the top of the hull. It has short sections at the rear plate and division plate to support the lower engine rails. Are you able to take some detail photos of the covers and frame around the radiator, before you close it in. My email is set up in my MLU profile. Thankyou for posting what you already have done. Nice British steering wheel too.

Petr Brezina · #**222** 20-02-17, 10:47

Quote:

Can you tell us about your engine?

Its not geniune carrier engine, it came from the old power unit, French made. Proper block, possibly war dated.

Quote:

Does your dash panel have the four fuzes in the top?

Yep, four fuses there.

Quote:

Are you able to take some detail photos of the covers and frame around the radiator, before you close it in.

No problem, will do that.

Petr Brezina · #**223** 20-02-17, 10:55

Not mine, but the same type of power unit.

Michael R. · #**224** 20-02-17, 14:25

Differences of housing packing, or instrument panel gasket, varied between country of manufacture, serial number, and model of carriers.

The Canadian production design change for 'Gasket - Instrument Panel' , part no. C01UC-105300, was introduced at serial number 1877. This black rubber material gasket appears on Canadian MK-I* series carriers, i.e. C01UC, C21UCM and C21UCG, (as shown by Dave G.). Retrofitting of the earlier Canadian production required the use of longer mounting bolts, C01UC-105311. Bulletin A-5, 25 Sept 1942, Item 16 refers.

The gasket material and part number(s) was changed for the Canadian MK-II* series, C31UCW, where it is made from two parts, the material is plywood.
Those part numbers are C31UCW-104856 and C31UCW-104857 as 'Spacer - instrument panel L.H. and R.H.' respectively.

Chilwell publishes the Langite gasket material for all British Universal Carrier production instrument panel gaskets as two parts, TL 13958 and TL 13964.

Ron Pier · #**225** 20-02-17, 16:49

I notice too that the petrol filler cap is at the opposite end of the tank to the Canadian MK2.

Ron

Petr Brezina · #**226** 20-02-17, 18:35

Quote:

Originally Posted by Michael R.

Chilwell publishes the Langite gasket material for all British Universal Carrier production instrument panel gaskets as two parts, TL 13958 and TL 13964.

Yes, thats your list, I was sourcing from

There are many differencies between British and Canadian production and early/late models. Very interesting to finding them out.

Lynn Eades · #**227** 20-02-17, 18:37

And is without vent pipes.

Petr Brezina · #**228** 21-02-17, 15:31

Yes, simplified and better (more ergonomic) design on fuel tank.
Evolution went to the right direction in this case, I guess

Petr Brezina · #**229** 26-02-17, 20:53

Lynn, here are few photos from "radiator area" as promised

Petr Brezina · #**230** 26-02-17, 20:57

Few more.
Some pipes connected today, engine almost ready for firing.

Petr Brezina · #**231** 12-03-17, 19:56

Few bits added - mirror, front el. conduits, engine linkage. Also start work on the visors...

Petr Brezina · #**232** 12-03-17, 19:58

More pics...

RichardT10829 · #**233** 13-03-17, 14:31

Looking good buddy. It may just be the angle, but that radiator looks a touch small. are you happy you have sufficient volume ?

keep up the good work.

Petr Brezina · #**234** 13-03-17, 15:48

It is small, Richie, you are right! But its also more efficient that the genuine one, so will see. Also electric fan gives a pretty good flow, so so far Im not worried about it - but its still just a theory...
Hopefuly will warm up engine this weekend and test it!

RichardT10829 · #**235** 13-03-17, 19:26

You won't really know until you start driving it buddy, and putting some load onto the engine so to speak.

Petr Brezina · #**236** 13-03-17, 20:39

Exactly, Richie! And Im really looking forward to it

Paul Dutton · #**237** 14-03-17, 09:39

I like the idea of a modern radiator and fan.
In my opinion, if it can't be seen and does the job better then why not.
Have you the details of fan and radiator please?? Or what thread was it in?
Paul

RichardT10829 · #**238** 14-03-17, 13:07

Paul, kenlow do a good fan. I can recommend a company called Pro Alloy for a modern rad (my last carrier had one) I donated a wrecked original as a pattern and they made me a bespoke rad. Very efficient indeed !! So much so that when we were stuck In heavy traffic in 30 degree heat my carrier was rather hot (over 200deg) normally the flatty won't cool after you reach that temp, but I was able to bring the temp down whilst stationary by raising the rpm slightly.

I was also running thermostats.

Contact at pro alloy is Chris Hazel.

Paul Dutton · #**239** 14-03-17, 19:59

Cheers for that mate, I'm a long way off but just taking notes for when bits are needed.
Paul

Petr Brezina · #**240** 15-03-17, 22:38

Finally got lower rad hoses, so if they will fit, she is ready for first run.
Also working on the main and side lamp brackets.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Project	ron	The Carrier Forum	3	17-07-17 22:00
A new project	Tim Lovelock	The Softskin Forum	15	17-07-12 13:58
FGT project	Tony Wheeler	The Restoration Forum	38	12-07-12 06:09
Project F15	Howard	The Softskin Forum	162	07-02-09 07:47
FOR SALE/TRADE: 1944 CHOREHORSE PROJECT for Signal Corps Wireless Power Unit Project	Alain	For Sale Or Wanted	1	21-02-07 00:11