![]() |
|
|
|
#1
|
|||
|
|||
|
Thank you Colin on the spring steel.
I will Hijack you thread just a little: From: The Sands Of Dunkirk by Richard Collier 1961. Page 265 Facts about DunKirk. Gort's army brought back: 322 guns (artillery pieces?) 4,739 vehicles 533 motor cycles 32,303 tons of ammo 33,060 tons of stores 1,071 tons of petrol What was lost /left behind: 2,090.000 british pounds. 416,940 tons of stores, 164,929 tons of petrol, 76,097 tons of ammo, 2,472 field guns, 20,548 motor cycles, and lastly, 63,879 vehicles. Over nine days 366,162 men were taken home. 68,111 were killed, wounded, or taken prisoner. They lost 109 fighters and 177 other aircraft. The author did years of research for this book (he interviewed 1070 eye witnesses, with details on each) He said that no one man could present truthfully the mammoth nine day exodus that involved countless million men and women. I find it hard to imagine.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
|
#2
|
||||
|
||||
|
Hi Lynn, Hijack away
![]() I have made a solid table top for temporary use of keeping my bearing surfaces flat. I have used some 20mm plate I had here so I can use it again when finished. I have a centre and a diameter finder and some instant clamps for keeping it all together while the process is complete and slow cooling. I think I can cut the internal gear on my plasma and that will be a fantastic saving and a quick process. |
|
#3
|
|||
|
|||
|
....but can't figure out how you are going to fit in the balls.......
This is better than Popular Mechanics magazine. Bob C
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada |
|
#4
|
||||
|
||||
|
Hi Bob, I have to weld two rings on top and the top one having a internal gear all round. Then I need to put the whole thing in my milling machine and cut a 3/4" grove the full distance around the top. The photos below show the first one welded and ground off and I had a prelim try at cutting gears on my plasma. I am quite happy with the result but I need to make time on the computer and draw a curved toothed ring for the last top section. There will be a bit of trial and error on that part I think. I am very happy with the result of the ring so far.
|
|
#5
|
|||
|
|||
|
Quote:
331 VI light tanks 77 Matilda 1's 23 Matilda 2's 184 Cruiser tanks It's amazing the English could field anything but a cricket team after such horrendous losses. And what a bonus for the Germans, I'd read once that up to the end of the war, most of their troops were moved either on foot or on horse back. Cheers Tim |
|
#6
|
|||
|
|||
|
Colin, I continue to be amazed at your range of skills. Fantastic work. great to see and thank you for the details.
Tim I measured my carrier width = 6 foot 11 inches sand guard outer edge to outer edge. So if all the vehicles lost at Dunkirk averaged the same width as a carrier, and they were parked side by side, then, with a 1 inch gap (that's allowing 7 feet per vehicle) they would form an unbroken line 84.688 miles, or 135.5 kilometers long. I hope I've done that right.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions.... |
![]() |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Door Resto | Barry Churcher | The Restoration Forum | 13 | 15-05-22 16:36 |
| FAT cab 13 No 9 resto | Mrs Vampire | The Softskin Forum | 27 | 29-09-21 07:11 |
| C15A resto | harrygrey382 | The Restoration Forum | 9 | 08-06-15 10:40 |
| another CAN m37 resto | Steve Wilson | The Restoration Forum | 11 | 25-08-12 16:57 |
| m 37 resto in new brunswick | pauljboudreau | Post-war Military Vehicles | 118 | 07-03-11 23:29 |