How To: Restoration of Ford M8 armoured car US Ordnance number 7373

[Big D]

Hi David

Thanks for that. Yes, I looked back myself and it has been a bit over three years since I started this thread. That's a lot of posts! It is very nice seeing it on wheels, and it would be great to learn a bit more about its history. Hopefully the historical data will keep on filtering out.

[colin jones]

Darryl, what can anyone say except "SUPERB" you attention to detail and workmanship is second to none and you will end up with a vehicle that will last way past you and me but will always have your name on it. They are such a cool looking machine. Are you going to get you 37 gas firing as that would be the cherry on top.
Great work.
Colin.

[Big D]

Hi Colin,

Thanks for that. That is quite a compliment, coming from a craftsman like yourself! They are a nice looking machine and I'm looking forward to getting it completed.

The gas gun does sound like a good option. I do have another 37mm gun coming from Belgium though. It looks relatively complete so blank firing is another option. We will see....

[Big D]

Hi all,

Just a quick update on what I’ve been up to since the M8 has been on its wheels.

I’ve tidied up a few more jobs on the hull. I’ve fitted the shock absorbers and tightened the torque rods. I still need to source one fixed torque rod, as one of the three I have is not right. I also still need to find a 1 ¼”-12 die nut to tidy up one of the threads on the adjustable torque rod mounts on the axle. I added a new DM-34 dynamotor to the other radio and have now fitted that to the radio tray, so that setup is good to go.

I have fitted some of the data plates to the driver’s area in the hull. One of them is slightly too wide so I need to find a sharp guillotine and shave 1mm or so of the side of the plate without bending it. Does anyone know where this small rectangular data plate showing dimensions etc goes on the hull? I have a feeling I have seen photos of this plate on the hull but I can’t locate that photo.

I still haven’t got the turret back here to the workshop so I have started work on a few other things to keep the project rolling. There always seems to be multiple small jobs on the go…

The gearbox is in pretty good shape but there is wear to the synchroniser and ring for 1st and 3rd gears. I have located these parts and they will be on the way to me shortly. The bearings seem to be in good shape but I will confirm once I have the main-shaft out. I’ll shortly start disassembling the gearbox in preparation for the arrival of the parts.

I will get the radiator dropped off to a repair firm this week for reconditioning. The exterior of it suggests it has been through a war, but I don’t know what the internal condition is like, so it will be interesting to see what they say. I will clean up the radiator fan diffusers in preparation for the radiator coming back.

I used a grease/gear oil slurry as lubricant in the pillow block but noticed that it seeped a bit of oil from the keyways. After a bit of research I used the tip about fitting a bit of cork into the keyway, and sealed it with a bit of flange sealant. We’ll see if that works. I have also started on the transfer case and will show some photos of that next week.

That’s all for today.

[Big D]

More photos.

[Big D]

Hi all,

I’ve been busy with work and life for the last few weeks and I haven’t posted for a while, so here are a few updates on what I’ve been up to on the M8.

I have stripped and reconditioned the transfer case. Overall it was not in bad shape and I don’t think it has been that long since it has been apart. All the flanges came off easily which I’ve found is a good indicator. The gears had some light corrosion on them from the transfer case sitting around with little oil in it. As per the photos, some of the teeth on a couple of the gears had some pitting resulting from the corrosion from that sitting around. I have cleaned that up and the pitting shouldn’t create any issues.

The bearings looked good and just required cleaning. I cleaned up all the gears and flushed and cleaned the internals. I found some oil seals ‘off the shelf’ from a local supplier which were the correct size for the bearing caps. The same seal is required for the handbrake drum bracket but the fit on this was a whole lot tighter, and it needed some persuasion to get it in there.

I did notice a very fine hairline crack in the front axle declutch housing. Looking back at my pre-disassembly photos, I see the crack was there and just visible under the old paint, so it might have been there for a long time with the paint and dirt holding it together. I have covered it in some epoxy adhesive which should seal it. I made up new gaskets, and cleaned all the shims from each bearing cap and fitted them as they were. All clearances seemed pretty good. I cleaned up the rest of the transfer case and a coat of paint freshened it up nicely. Let’s hope it doesn’t leak!

I fabricated some retainers for the rubber mounting cushions out of a bit of channel with some angled steel which will form the mounting strips on the sides. I will finish the welding and tidy them up over the weekend and then hoist the transfer case up into place on the hull.

[Big D]

More photos.