|
|
#1
05-03-20, 20:58
|
||||
|
||||
British Sand Channels
Hello all,
I am looking for a set of British sand channels, or worse case scenario (Marston mats) for my truck. I'm located in the U.S., so I know it will be next to impossible...  Thank you.
|
|
#2
06-03-20, 01:10
|
||||
|
||||
|
Phillipe I have PSP or Marston mat in various styles and lengths. Where in the US of A are you? I would bet you are not close to me.
I am in Ontario Canada, yours for a low fee, send me your email as pictures wont load
__________________
Robin Craig Home of the Maple Leaf Adapter 2 Canadian Mk1 Ferrets Kawasaki KLR250 CFR 95-10908 ex PPCLI Canadair CL70 CFR 58-91588 Armstrong MT500 serial CFR 86-78530 Two Canam 250s Land Rover S3 Commanders Caravan Carawagon 16 GN 07 Trailer Cargo 3/4 T 2WHD 38 GJ 62
|
|
#3
06-03-20, 16:26
|
||||
|
||||
|
British Sand Channels
Hello Robin,
Much appreciate the reply... I am located in the Ft. Lauderdale/Pompano area; you're absolutely right, not close at all! but not impossible... This is my emai Best regards, Philippe Last edited by Hanno Spoelstra; 25-03-20 at 12:10. Reason: email link inserted for spam control
|
|
#4
06-03-20, 22:15
|
|||
|
|||
|
Wouldn’t be hard to get them laser cut and folded if you can get specs.
__________________
1943 Willys MB Willys Trailer 1941 Fordson WOT 2H 1941 Fordson WOT 2H (Unrestored) 194? Fordson WOT 2D (Unrestored) 1939 Ford 1 ton utility (Undergoing restoration) 1940 Ford 1 ton utility (Unrestored) 1941 Ford 1 ton utility (Unrestored) BSA folding bicycle BSA folding bicycle 1941 Ford/Marmon Herrington 3A gun tractor 1941 Ford/Marmon Herrington 3 gun tractor (Unrestored) 1941 Diamond T 969 (Unrestored) Wiles Junior Cooker x 2
|
|
#5
07-03-20, 02:09
|
||||
|
||||
|
Phillipe,
I agree with Jack Neville. However, are the ones you show originals or reproductions? I know my friend Peter Duggan with his Ford of Canada Lynx is lusting for sand channels and I honestly think if we can figure out the profile they can be made. The ones you show are similar to others of that era and lack the diamon strengthening pieces that the Ferret ones have, with which I have more familiarity. .
__________________
Robin Craig Home of the Maple Leaf Adapter 2 Canadian Mk1 Ferrets Kawasaki KLR250 CFR 95-10908 ex PPCLI Canadair CL70 CFR 58-91588 Armstrong MT500 serial CFR 86-78530 Two Canam 250s Land Rover S3 Commanders Caravan Carawagon 16 GN 07 Trailer Cargo 3/4 T 2WHD 38 GJ 62
|
|
#6
07-03-20, 06:24
|
||||
|
||||
|
British Sand Channels
Hello Jack/Robyn,
The ones shown in the photos above may be the closest to the original WWII British sand channels... For what I have seen of original photos (Attached) they're close; or rather seem to be spot on, so may be originals... But maybe someone with more knowledge on the subject can answer that... I "borrowed" the photos from the net and know that the one person that may be able to answer our question or help with dimensions is Paul Lincoln from the UK... He has access to Mr. Knudsen's truck and could get the information... In the meantime, we can just study some original photos and compare... Hope that, again there may be a strong interest by someone with the knowledge and resources to get some of these made since there seems to be enough interest out there...
|
|
#7
25-03-20, 04:41
|
||||
|
||||
|
British Sand Channels
While looking for more information I came across this...
https://zerzura.me/long-range-desert-group/ And wonder if the sand channel would be for a smaller vehicle... Seems quite a bit narrower than one used for a 30 CWT truck...
|
|
#8
25-03-20, 05:55
|
|||
|
|||
|
Based on the photos posted, Philippe, there are indeed two different sizes of wartime sand channels. The colourized photo shows the wide version. Note the large empty space on that set from the outer longitudinal edges of the channel and the outer rows of holes. Also where the upper edge stows and how the lower edge is situated below the top recess of the wheel well.
All other photos show a narrower channel with very little outer edge empty space and the channels when stowed, fit completely within the gap on the sides of the truck between the upper edge of the wheel well and the lower edge of the top reinforcing channel of the box. Why there are two different versions is an interesting puzzle, but you at least now have proof they both exist and were both used in the same theatre, by the same type of vehicles. You are making progress. David
|
|
#9
26-03-20, 01:51
|
||||
|
||||
|
British Sand Channels
I couldn't agree more, there were many different size vehicles in the desert, so it would make sense that there would be different sizes available to correspond to their size and weight... Your observations are spot ot. There is no doubt there were different sizes available and finally we have proof... It is quite nice to see an original piece... A first!
|
|
#10
26-03-20, 04:05
|
|||
|
|||
|
I would be inclined to err on the side of caution, Philippe.
All we know for certain, looking back at 75+ year old photos, is that two different size channels existed. Why, is very much still unknown. The other interesting thing here is that all these photos are of one type (weight class) of vehicle. That suggests both sizes could do the job for this one type of vehicle. One possibility for this showing up could be the bigger channels came first. They worked but may have been heavy and difficult to work with. Or, smaller ones developed to save steel or costs. What would be interesting at this point, would be to find photos of a different weight class of vehicle equipped with channels and see if two sizes show up there as well. David
|
|
#11
26-03-20, 15:00
|
|||
|
|||
|
Sand Channels
Field Marshal Alexander's car in the Canadian War Museum has some mounted on the back and it may be possible for someone to get permission to photograph and measure them once the museum reopens to the public. This is an old photograph from 10 years ago so I am not sure where this vehicle is currently located within the Lebreton Gallery
|
|
#12
26-03-20, 17:10
|
|||
|
|||
|
Interesting photo, Ed.
I wonder if there is a correct way and an incorrect way to stow these channels on a vehicle? On Alexander’s vehicle, the two channels are nested into each other and look at the big gap between them and the retaining bar that is supposed to secure them in place. At the very least they would make quite a noise sitting like that when the vehicle was on the move, if not get lost altogether. When you look at the earlier photos posted, you see some vehicles where the two channels are cupped against each other and fit snugly into their stowage brackets in that manner. On the other vehicles, the channels are nested when stowed and have extra web straps added to hold them in place, with lots of extra space in the brackets. Interesting. David
|
|
#13
26-03-20, 19:40
|
||||
|
||||
|
British Sand Channels
All very interesting points, and very happy to see another photo of the smaller channels... It totally makes sense that they would exist, as did the larger size. As to how to properly carry them without loss and having them rattle their way down the road is another matter...
I believe that we were trying to ascertain the original dimensions of the larger size channels... While looking for this answer, I thought that one big clue would be in this first photo... If you compare it to the diagram, these should be as wide as the distance between C and B in theory, except... 1- We don't know if the truck in the photo has the bed in the diagram... 2- We don't know width of the channeling that surrounds the box... But could come close... The difference between C and B is 15-1/8 or 384.17 mm which might just be the ticket and what my friends Chuck, Bob and I came up with... As for the length, somewhere in the 81" or 6.75' seems in proportion... I know there are some out there, but someone willing to help has to come up with the information... Last edited by Philippe Jeanneau; 29-03-20 at 05:45.
|
|
#14
27-03-20, 18:54
|
||||
|
||||
|
4B1 body
Quote:
__________________
Regards, Hanno --------------------------
|
|
#15
28-03-20, 19:34
|
||||
|
||||
|
British Sand Channels
Absolutely beautiful job! Very good to see a reproduction this side of the pond!! The changes are minor, and the sheetmetal could very well be 12 gauge to make it manageable for one person...
|
|
#16
28-03-20, 19:39
|
||||
|
||||
|
British Sand Channels
I think I am your first customer! and regarding shipping, Fastenal does a great job and very inexpensive compared to regular carriers... Luckily, there is one about 5 miles from my house...
|
|
#17
28-03-20, 23:25
|
|||
|
|||
|
Wonderful job...........
Hi Chuck
Will you share dimensions, width at the two folds, thickness, drilled or punched, etc. weight, length May be the second customer once the borders are open again........... Stay healthy
__________________
Bob Carriere....B.T.B C15a Cab 11 Hammond, Ontario Canada
|
|
#18
29-03-20, 01:21
|
|||
|
|||
|
Quote:
Having the dimensions published, and/or cutting files allows local production in country of production currencies without shipping, duties and applicable fees.
|
|
#19
18-04-20, 14:02
|
|||
|
|||
|
Reproduction sand channel mentioned (with photos) on https://forums.g503.com/viewtopic.php?f=50&t=314807 listing was dated 3 Apr, marked as sold yesterday. It isn't stated what the builder's reference was.
|
|
#20
19-04-20, 00:01
|
|||
|
|||
|
Quote:
Alex
__________________
Chevrolet C8 cab 11 FFW BSA Folding Bicycle
|
|
#21
19-04-20, 01:03
|
|||
|
|||
|
Alex, maybe usage and tyre profiles changed them? In post #6 on the left they are more shallow than those on the right. The design looks like the angled outer edges would "hold" the sand in place as the weight pushed them down. They would have been designed to carry the weight with the "assistance" of the captive sand, and no more. As some would know, running a really low tyre pressure gives a much larger foot print and therefore much better traction. With time contraints, the load, and the available equipment, sometimes decisions would have been made against deflation.
Depending on how these were used would dictate the shape after some use. Maybe the narrower square sided ones were just for cars? I would think that when the truck ones were sitting on a flat surface, the center and both edges would be touching the ground or that the center would be just clear. Stacking and stowing would be easier.
__________________
Bluebell Carrier Armoured O.P. No1 Mk3 W. T84991 Carrier Bren No2.Mk.I. NewZealand Railways. NZR.6. Dodge WC55. 37mm Gun Motor Carriage M6 Jeep Mb #135668 So many questions....
|
|
#22
02-01-21, 03:16
|
|||
|
|||
|
old post but i could use sand channels and mats
Hi, I am building a lrdg ford pilot car and could use sand channels and the sand mats that were rolled up on the fenders. Any help would be greatly appreciated.
p.s new guy here and i will have a ton of questions and parts queries for lrdg related equipment to fit my truck out. so hello and thanks in advance. scott
|
|
#23
02-01-21, 06:23
|
||||
|
||||
|
Scott I am just above you in Ontario and have ways and means of sending some PSP down to you if you want
please email me
__________________
Robin Craig Home of the Maple Leaf Adapter 2 Canadian Mk1 Ferrets Kawasaki KLR250 CFR 95-10908 ex PPCLI Canadair CL70 CFR 58-91588 Armstrong MT500 serial CFR 86-78530 Two Canam 250s Land Rover S3 Commanders Caravan Carawagon 16 GN 07 Trailer Cargo 3/4 T 2WHD 38 GJ 62
|
|
#24
04-01-21, 00:45
|
|||
|
|||
|
i have sent e-mail
i have sent email thanks scott
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Wanted: PSP sand ladders | Zac Chappell | For Sale Or Wanted | 4 | 28-08-19 20:28 |
| Canadian Ferret / Sand Channels | Robin Craig | Post-war Military Vehicles | 24 | 02-09-13 19:56 |
| Some of our CMP's out playing in the sand | paul Lincoln | The Softskin Forum | 9 | 28-04-11 02:13 |
| Sand chains... | Rolf S. Ask | The Softskin Forum | 30 | 17-12-06 13:22 |
| Sand blasting | Matt | The Restoration Forum | 16 | 16-03-04 02:04 |
Linear Mode
