Look what a friend gave me. Need help to ID

[rob love]

Now for some more "new to me" oddities. The variometer has a different cord coming out of it. Was this a ham radio operators post war modification?

Aslo, the metal plate does not match up to the wooden block on the mount. The metal plate wants flathead screws while the wooden block is not indented to accept the plate.

Next photo is a lamp assembly, a smaller than usual dogbone, and a couple of little ceramic electronic items. Any help?
Third is one of the small dogbones next to the normal larger dogbone. I got about a half dozen of the regular dogbones, then some with the cord for the crystal calibrator, and the small ones with the cord for the crystal calibrator.

There was also one dogbone with a amperage meter spliced into it.

[rob love]

Next is a photo of some more misc stuff. There are multiples of most of it. I am guessing the green brackets with the neck and chest straps are to hold a microphone in the "stowed/ready" position?

[rob love]

Another box of stuff. It included one of the nicest spares box with key that I have seen. That will be moving into the carrier. Does anyone recognize the little test box, or what is inside the sealed box? The previous owner didn't have the heart to open the boxes, and neither do I unless it is something I would actually use. One shot shows the ID plate on the table.

[rob love]

Again, I am no radio collector. They are just an accessory to sit in the vehicle, so I know little about the oddball stuff. Please enlighten me.

[Chris Suslowicz]

Originally Posted by rob love

Now for some more "new to me" oddities. The variometer has a different cord coming out of it. Was this a ham radio operators post war modification?

No idea, may be specific to the Canadian amplifier. I've not seen that variometer extension before.

Aslo, the metal plate does not match up to the wooden block on the mount. The metal plate wants flathead screws while the wooden block is not indented to accept the plate.

The block may just be a spacer because I think the variometer fits to the amplifier table frame so does not need an adapter plate

Next photo is a lamp assembly, a smaller than usual dogbone, and a couple of little ceramic electronic items. Any help?
Third is one of the small dogbones next to the normal larger dogbone. I got about a half dozen of the regular dogbones, then some with the cord for the crystal calibrator, and the small ones with the cord for the crystal calibrator.

There was also one dogbone with a amperage meter spliced into it.

Small dogbones (6-pin - 6-pin) are for the earlier WS19 Mk.2

Lamp is the standard "Lamp Operator" - you remove the red lens and the bulb from the supply unit, screw the cable in instead, and clip the lamp somewhere where it sheds useful light without dazzling you.

The ceramic items are high-voltage silver-mica capacitors.

The dogbone with the spliced-in meter is a later bodge by someone.

Be careful with the AC power supplies: the 6X5 rectifiers are a weak point and if the insulation between the valve heater and cathode fails they can destroy the transformer.

Best regards,
Chris.

[rob love]

Thanks Chris.

What about the large silver cables that allow the plugs to be stacked? Are those also a amplifier item?


These were held in a technical college since the war, so some items may have been modified for their test purposes. Apparently the stuff was boxed up after the war was over and refound just a few years ago when they were given to my friend.

[Bruce Parker (RIP)]

It's all Canadian Amplified No.19 stuff.

[rob love]

I guess I had better be looking for some parts manuals. It is not quite as easy as looking for regular 19 set stuff.

[Bruce MacMillan]

WOW! what a nice bit of kit to find.

Lets start:

The amplifier/power supply sits on top of the rack over the 19 set. This rack is bolted to a bench or table. It looks like you're missing the amplifier power supply.

The variometer is standard issue for the amplifier CES. The bit on the end is a protection circuit for the 19 set. It shorts the receiver aerial input when transmitting.

Most of the cables appear to be used with the amplifier. The power supply is AC/DC so there were separate power cables.

The little grey box with a toggle switch is the send/receive switch when using the amplifier with a WS22.

The photo of the complete set is one I have had for years so I don't know where it came from. If it's from any member here please chime in. It shows cable connections.

The manual you'll want is the "Working Instructions Amplifier C19 *experimental". Chris could confirm as I think it's on the WS19 group website.

If the little AC supply for the WS19 is still good it can be used for years if care is taken. The other photo was my operating bench back in Canada. I was setting up the C19 amplifier on the left running from AC as I didn't have the four 6V 145AH batteries normally used. The 19 set on middle shelf is being run with the AC supply. The blue box to the left is a variac which I used to power the set up. It's lasted over 15 years using this method.

[rob love]

Thanks for that photo Bruce. I now see what the intent of the table is along with the positioning of most of many of the cables. I guess the hunt will be on for an amplifier power supply. I guess I had best check with my friend to see if he has it.

[James D Teel II]

After having looked for years for a decent 6/6 crystal calibrator dog bone, I've now seen several in the last few days, one of which I went ahead and purchased so I can retire the one I restored. I was also able to pick up a complete spares box like that one. It's amazing to me that there is still so much good stuff out there after all these years.

That's a nice grouping you've been given. I like being able to see the more rare bits.