![]() |
|
#1
|
||||
|
||||
![]() Quote:
This is not a Morris "Tilly" but a Morris Series Y commercial, usually a van or light truck. There were some military ambulance versions with canvas covered bodies. Lang Kidby found a Series Y and had plans to drive it across Europe at one time.
__________________
Richard 1943 Bedford QLD lorry - 1941 BSA WM20 m/cycle - 1943 Daimler Scout Car Mk2 Member of MVT, IMPS, MVG of NSW, KVE and AMVCS KVE President & KVE News Editor |
#2
|
||||
|
||||
![]()
Thanks for the expert info Richard... I knew if I posted it someone would know - probably you!
__________________
Film maker 42 FGT No8 (Aust) remains 42 FGT No9 (Aust) 42 F15 Keith Webb Macleod, Victoria Australia Also Canadian Military Pattern Vehicles group on Facebook https://www.facebook.com/groups/canadianmilitarypattern |
#3
|
|||
|
|||
![]()
I've been pretty quiet here, but have reactivated my restoration thread here;
http://www.mapleleafup.net/forums/sh...947#post206947 I'm not sure what the protocol is; should I keep any restoration work over there? I figure that this one could be a general discussion about the wartime Inters, while the resto thread could just be specific to my truck? After my first visit to Corowa, I'm keen to have mine ready for 2016. Doesn't seem to be much interest in the wartime Inters, but I hope to add my bit to help change that. I have my wife on board, so that's a big bonus! I thought I'd also ask these questions here, as they relate to these vehicles generally, and are not just restoration-specific. A couple of questions, or an invitation for suggestions. 1) The front tyres. Obviously, the 18x10.50 tyres are like hens' teeth. I understand that both Gamma Goat and DUKW tyres are close enough to work. Are these tyres available in Australia? And if so, do bar-tread tyres present a particular challenge for use with such a vehicle? 2) 20" wheels. One suggestion was to modify Blitz rims to suit. This would be a bit of work, as the stud number and radius is different. Would such a plan be feasible? 3) Replacement with spider hubs. My spare truck has commercial spider hubs, and I wonder what would be involved with a straight swap? I'd like to keep the current wheels if at all possible, but there's a precedent for the use of spider hubs. Mind you, do they have another hard-to-find tyre spec? 4) The General Service body. Is this body similar to the other types, such as the Dodge and Chev varieties? The metal brackets and structure could possibly be a match, and I have nothing above the floor, apart from the vertical section against the cab. So, it continues. Please excuse my enthusiasm! As I say, I'm open to suggestions, thoughts, and corrections. I'd like to see at least one WW2-dated International at Corowa next year. Cheers, Matt
__________________
1942 International K5 3-ton truck ARN 43362 1940 Holden-bodied Chevrolet staff-car 1941 Holden-bodied Chevrolet staff car Last edited by Matt Austin; 15-03-15 at 03:53. |
#4
|
|||
|
|||
![]()
My father many years ago in Nowra restored a K5 and was lucky enough to find many more wreaks for missing parts at local saw mills.
The K5 should have 20 inch split wheels front and rear. The 20 inch wheels are called suicide wheels and no one much in the tyre game will know anything about them or touch them. They are different to the split rims and two piece wheels still in use to day. The 18 inch wheels and hubs are military but not K5. 18 inch tyres were standard on american and Australian trailers during the war. The tyres are no longer advailible in Aust except for a very low speed rated tractor tyre of in correct tread pattern. The cabin tops and rears will very between WW2 K series. They were imported during the earlier part of the war when we were desperate for trucks as partly knocked down and supplied as bonnet to windscreen and doors only. The roof and rear part of the cabin is all local stuff done in a hurry and cheaply. The cabin rear is usually wooden frame with sheet metal nailed and bent over the top. Some had canvass roofs and some had sheet metal. Local rear cargo bodies usually fitted which could be all timber or metal runners with timber planks on top. Some ......but not many had a two speed rear diff fitted and worked by a a simple push\pull rod link from the floor of the cabin. They were assembled in Melbourne and I think it was Licombe in Sydney. Last edited by Ron King; 15-03-15 at 11:45. |
#5
|
|||
|
|||
![]()
The K series were sold off much earlier than the trucks used later in the war and the fact they were 2x4 with a civie friendly type body fitted ment they were snapped up by a truck starved post war Australia.
They were worked hard post war and by the 1960s most were worn out and disappeared. They were much more useful carting goods around a big city than something like a Bliz. Off road for a 4x2 truck they are good with the duals on the rear and a good low first gear. Nice to drive and if I remember correctly they Max out at just over 50 mph. The green diamond engine is OK but never earnt the name of other truck motors of the time and didn't seem to last as long as a Hercules GMC or Dodge or ford 8 etc K4 and K6 were also used with the K5 seems to be the most numerous surviving to day. Ron. |
#6
|
|||
|
|||
![]()
If you go to the correct spider front hubs and 20 inch wheels new tyres are still advailible in 7.50 x 20 and 8.25 x20.
The 8.25 x 20 is a grader tyre advailible in a semi lug design well suited to a K5. You will find the tyre crowds will not fit the tyres and you have to do it your self............just be very careful as it takes a while for most people to get their heads around the way the split wheel on the K5 works and you must wrap a long chain around the wheel loosely all the way around and hook it back on its self when inflating in case the old rims do not sit in the wheel correctly during inflation. Take note the locking rim is not perfectly to round ????? and is flexed off the wheel by a bar at the cut away in the locking rim provided. The out of round shape holds it in place and the split in the wheel on a deflated tyre also moves together to give room to remove the rims. Last edited by Ron King; 16-03-15 at 07:22. |
#7
|
|||
|
|||
![]()
Thank you very much, Ron, that info is gold!
I was aware that the 18x10.50 was a trailer type, having seen it on a field kitchen trailer (I think) once before. I thought at least one variety of smallish Chev truck or ute also used them? I'll take your suggestions, and appreciate your having taken the time to reply. You've described my truck perfectly, as shown in the attached pic; "The roof and rear part of the cabin is all local stuff done in a hurry and cheaply. The cabin rear is usually wooden frame with sheet metal nailed and bent over the top. Some had canvass roofs and some had sheet metal." I wonder if I'll be able to register it with new wood, rebuilt as it was originally done? Lots to think about. I also attached a pic to show what a wash does, to remove sixty-something years of grime. There's no evidence of the ARN, but the paint is mostly good. Cheers, Matt
__________________
1942 International K5 3-ton truck ARN 43362 1940 Holden-bodied Chevrolet staff-car 1941 Holden-bodied Chevrolet staff car |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Heads Up: International truck in AUS | motto | For Sale Or Wanted | 8 | 18-06-12 15:32 |
International Security | Brad Mills | The Sergeants' Mess | 2 | 14-07-09 20:25 |
Australian International manual on eBay | Grant Bowker | For Sale Or Wanted | 0 | 14-03-09 13:58 |
International AL-130 | Rod Diery | Post-war Military Vehicles | 4 | 12-11-07 08:28 |
An international call | Keith Webb | The Sergeants' Mess | 6 | 22-01-04 15:39 |