Reference: Plans How to build a tool box for a CMP truck

S. Dafoe Plans How to build a tool box... 04-09-03, 15:13

Pete Ashby tool box 05-09-03, 21:53

S. Dafoe Thanks Pete! 08-09-03, 14:19

Pete Ashby Drawings 08-09-03, 22:39

George McKenzie Plans How to build a tool box... 19-11-07, 18:31

George McKenzie How to build a CMP box 29-11-07, 06:07

Bob Carriere Thanks George 10-12-07, 16:07

Mike Timoshyk CMP Spare Tire Carrier and... 03-03-08, 21:35

Jon Skagfeld Mike: You can take pics,... 04-03-08, 00:47

Mike Timoshyk CMP Tool Box end of Day 1 04-03-08, 02:23

Gordons clam shell clamps 04-03-08, 03:40

Mike Timoshyk Clamshells 04-03-08, 04:07

Bob Carriere Go for it Mike....... 04-03-08, 04:28

chris vickery Considering the complexities... 04-03-08, 13:23

Mike Timoshyk material considerations 04-03-08, 13:35

Hanno Spoelstra Glass-reinforced plastic... 04-03-08, 13:57

Mike Timoshyk Grp ???? 04-03-08, 23:20

Yeo.NT The best reproduction of a... 05-03-08, 01:50

Alex Blair (RIP) Walter Brand and Albert... 05-03-08, 02:53

Mike Timoshyk Petrolia 05-03-08, 04:13

Mike Timoshyk CMP Toolbox Day 3 06-03-08, 05:31

Bob Carriere I prefer the...... 07-03-08, 01:24

Geoff Winnington-Ball (RIP) Myke, you needs some... 07-03-08, 02:12

Mike Timoshyk Screw Top...... 07-03-08, 06:11

Mike Timoshyk day 4 08-03-08, 03:18

Alex Blair (RIP) Gas Axe..?? 08-03-08, 14:29

Mike Timoshyk Navalese 08-03-08, 23:09

More replies below current depth...

Walter Brand Hello Mike: I hear you need... 25-03-08, 04:17

Mike Timoshyk snuck into garage for an... 13-03-08, 03:49

Alex Blair (RIP) Mike .. I'm curious to know... 13-03-08, 11:52

Mike Timoshyk Type of welder 14-03-08, 17:11

More replies below current depth...

Walter Brand pics i hope 25-03-08, 05:26

Mike Timoshyk clam shells 25-03-08, 13:45

Mike Timoshyk cleaned up 26-03-08, 01:31

More replies below current depth...

#21

06-03-08, 05:31

Mike Timoshyk Mike Timoshyk is offline

Addicted to Drab

Join Date: May 2006

Location: Windsor Ontario

Posts: 664

CMP Toolbox Day 3

A little progress....had some snow to clear after the plow came by.

Cut the curve on the 2 sides to accommodate the spare tire and did some layout work for the partition and the top. I have no plasma cutter but have managed to scarf the material with a grinder and then used tin snips and bending back and forth...and finish off with the grinder. All in all not too bad. The top is 1/8 plate....I will probably use the good ol' gas axe tomorrow.

Bob...it's a Jackson Triggs Cabernet Merlot

till tomorrow

Mike in Windsor Ontario

Attached Images

box day 3.JPG (117.2 KB, 162 views)

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
*Reference:* CMP tool box and spare tire holder plans	George McKenzie	The Restoration Forum	37	25-12-22 14:30
LP2 VR 2225 Build	Dale Jordan	The Restoration Forum	255	25-07-18 07:45
*For Sale:* Carrier/Truck Tool	B. Harris	For Sale Or Wanted	11	05-05-15 07:52
*Reference:* Ford CMP Truck- Battery Holder plans	Jacques Reed	The Restoration Forum	14	17-09-12 22:35
My GM engine number when was it build??	8threcce	The Restoration Forum	7	09-01-12 08:39

All times are GMT +2. The time now is 02:09.